All

Why are you guys all trying to be economists?? Suzuki probably employs hundreds of people that sit and analyze data trends, inflation, market values, and economic conditions so they know how to price vehicles. It's not complicated. The price of the bikes will be similiar to KTM and Yamaha. Even if they only update cosmetically the price is still going...

If you are unhappy with their service you need to go talk to the service manager. Go in with an open mind and try not to be an a-hole. Give them an oppurtunity to explain their delays. Then explain what you are unhappy with. Go over the hours they billed you for and what changes could have been made to...

Yes you still need to do a fuse because if you have a short you don't want to kill your radio. Most modern cd players have overload portection/fuses, but they aren't 100% fail-safe. Like mototyme mentioned, you would also be smart to put in a master switch so you can turn the power off and on without unhooking your wires...

Sounds like we ride alot of the same places. i've probably seen you around before. Let me know if you ever want to come ride Galesburg, i'm a member and can have you out as a guest.

Yes i'm in Galesburg. I ride at Galesburg MC alot and I also have my own track near Knoxville. Where do you ride? Does Aledo still have that track and trail place? I remember going there like 10 years ago when I was younger.

When I was a young kid (about 3 years old) I saw Bob Hannah at a national and approached him for his autograph. I got up to him and said "can i have your autograph Ricky J? Obviously I was confused who he was. Hannah told me he was going to punch me in the mouth for calling him Ricky...

You can run it off your truck battery, but i wouldn't do it. You're only going to have about 1 hour of play time at a moderate sound level if youve got a good battery before you will draw to much charge out of the battery to start. You're best bet is to just buy a good Optima deep cycle...

They make a big difference. I have never heard of any negative complaints against them or vortex ignitions. They are a little bit pricey but are one of the best mods to do on a 250f.

Hey 526 smell my fingers now

How about 3 straight face wall jumps in a row, the third dropping off into a gravity hole with the other side a launcher take-off with a set of stadium whoops that break into moguls. Run the moguls through the following corner.

Are you looking for a mod motor or just rebuilding? I do service work in IL and have lots of experience.

I have a a pair of Gaerne SG10s size 10 for sale. They are very lightly used, i'm guessing about 20 hours or less. They are the white 2010 models. A friend gave these to me because he was getting out of MX but I don't wear them because I have some custom ankle braces fitted to my Astars. Let...

I think the less talked about, but biggest contributing factor to poor local district racing problems is there is hardly any spectators at races anymore. The spectators are the money makers for the promoters. I can remember when we loaded up a car full of friends (or 2 or 3) and went to the races where we payed our gate...

True, but even with the auto decompression 50 psi is too low. a normal reading would be no less than 100 psi. The only true way to do it is with a leak down tester at TDC

Hey ryan look at this huge sand booger i'm about ready to pull out

BTW where are you at in IL? I do service work at pretty affordable rates (alot cheaper then the shops). I'm in Galesburg if you need anyone to do some work for you.

need to cut new valve seats and replace the valves. That's the only way he's going to ever get a good seal again between the valve and seat. You should probably do all 4 valve at the same time if he can afford it. if not, at least the 2 exhaust. Always replace together, or at least in like pairs...

i've always used wiseco and had good results. Their kits are usually cheaper then piecing together an oem kit.

Hondas only have one cam, less length of timing chain, smaller cylinder head, 32 spoke rims, the lightest hubs, nice bolts throughout with dished out heads, and the frame is several pounds lighter then the other. Honda doesn a great job with fit and finish of their products so it should be no surprise they are the lightest.

Yes you got it right, good job! Set the spring in place and then slide youre inned chamber in until it bottoms out, sitting square in the spring seat. I like to measure from the top edge of the outer fork tube (make sure it doesnt move on you, I like to wrap a piece of masking tape around the...