Let's see/review those 2019 kx450s

Jbulz
Profile picture for user Jbulz
Posts
871
Joined
3/29/2016
Location
Ithaca, NY, USA
Jbulz 6/24/2020 8:43am
6/24/2020 8:43am
kkawboy14 wrote:
I purchased this to set my own! Is this the best setting? [img]https://p.vitalmx.com/photos/forums/2020/06/20/433479/s1200_79FF6179_6B19_43CB_BECF_D3DA4D895FA1.jpg[/img]
I purchased this to set my own! Is this the best setting?


Cashmoney24 wrote:
Yup. Don’t forget to do the fi as well, and per his review, use the white coupler. Here’s a link to his review article (with upgrades)...
Yup. Don’t forget to do the fi as well, and per his review, use the white coupler.

Here’s a link to his review article (with upgrades) which has a good breakdown and explanation of the settings. Good read altogether.

https://www.keeferinctesting.com/motocross-testing/tag/KX450
kkawboy14 wrote:
Cool that’s what I read!
It doesn't matter which coupler you're using. If you flash any of them to all 0's it will behave like the green one. If you plug in the black or white and read the fuel/ign tables you'll see the offset values for those couplers and the associated "Map 1/2/3" in the datastream screen.

I think Keefer made a mistake, because the map he posted is just the stock white one.
2
Cashmoney24
Profile picture for user Cashmoney24
Posts
36
Joined
3/7/2020
Location
Harpers Ferry, WV, USA
Cashmoney24 6/24/2020 11:11am
6/24/2020 11:11am
Jbulz wrote:
It doesn't matter which coupler you're using. If you flash any of them to all 0's it will behave like the green one. If you plug...
It doesn't matter which coupler you're using. If you flash any of them to all 0's it will behave like the green one. If you plug in the black or white and read the fuel/ign tables you'll see the offset values for those couplers and the associated "Map 1/2/3" in the datastream screen.

I think Keefer made a mistake, because the map he posted is just the stock white one.
Pretty sure that’s the same map that MXA has posted on their site and it seems to be the go to map for a lot of owners as well. I could be wrong though.

Think you may have a point on the white coupler. MXA doesn’t say anything about which coupler to use. I can’t see why it would matter which one you are using as it is being rewritten.
centralcalmx 6/24/2020 11:48am
6/24/2020 11:48am
If anyone has a set of firm front mounts they want to let go please message me.
They have been out for a few weeks


datkin128
Profile picture for user datkin128
Posts
279
Joined
12/23/2015
Location
Lakewood, CO, USA
datkin128 6/24/2020 1:38pm
6/24/2020 1:38pm
cmotodad wrote:
Any thoughts on 2020 KX450 forks? I am 180 lbs. with 5 hours on the bike. Feel like they are just getting a bit soft. Stock...
Any thoughts on 2020 KX450 forks? I am 180 lbs. with 5 hours on the bike. Feel like they are just getting a bit soft. Stock springs with 5cc more fluid per leg firm it up a bit? Thanks
stax199 wrote:
My riding gear was 23l bs!! FC wouldn't sell me my replacement springs until i weighed EVERYTHING. .. all agree increased sring rate will help alot.
So Stax, I just had pro circuit do my suspension. It needed a rebuild so I had them set it up while they were at it. They did .53 springs in the front and a .57 (not sure if it’s .57 or 5.7) in the rear. Haven’t received it yet, but looking forward to more holdup on bigger hits.

The Shop

See All »
quadzrulebro 6/24/2020 1:50pm
6/24/2020 1:50pm
Does anyone know of a screwdriver that works to adjust fork compression damping with 1 1/8th bars when the bar clamps are in the forward holes? It is a PITA to have to remove the bars to adjust compression.
bh
Profile picture for user bh
Posts
949
Joined
12/25/2016
Location
Piedmont, SC, USA
bh 6/24/2020 3:50pm
6/24/2020 3:50pm
quadzrulebro wrote:
Does anyone know of a screwdriver that works to adjust fork compression damping with 1 1/8th bars when the bar clamps are in the forward holes...
Does anyone know of a screwdriver that works to adjust fork compression damping with 1 1/8th bars when the bar clamps are in the forward holes? It is a PITA to have to remove the bars to adjust compression.
Flat head bit with a 6mm wrench should work.
Moto520
Profile picture for user Moto520
Posts
3666
Joined
2/4/2013
Location
Schaumburg, IL, USA
Moto520 6/24/2020 3:58pm
6/24/2020 3:58pm
quadzrulebro wrote:
Does anyone know of a screwdriver that works to adjust fork compression damping with 1 1/8th bars when the bar clamps are in the forward holes...
Does anyone know of a screwdriver that works to adjust fork compression damping with 1 1/8th bars when the bar clamps are in the forward holes? It is a PITA to have to remove the bars to adjust compression.
It’s a major pain. The flat style compression adjusters that you can get from pro circuit don’t work due to part of the cap being raised on one side. I go in with a tiny screwdriver from a side angle. The compression adjuster gets pretty chewed up but what can you do?
brandon_21888 6/24/2020 4:10pm
6/24/2020 4:10pm
quadzrulebro wrote:
Does anyone know of a screwdriver that works to adjust fork compression damping with 1 1/8th bars when the bar clamps are in the forward holes...
Does anyone know of a screwdriver that works to adjust fork compression damping with 1 1/8th bars when the bar clamps are in the forward holes? It is a PITA to have to remove the bars to adjust compression.
T


Got this off amazon... works perfect

Neiko 01328A Low Profile Offset Screwdriver Set, 7 Piece | Portable Keychain Clip Included https://www.amazon.com/dp/B078MT1XQJ/ref=cm_sw_r_cp_api_i_a198EbPBQ58G9
3
RGaede
Profile picture for user RGaede
Posts
210
Joined
1/10/2014
Location
Albuquerque, NM, USA
RGaede 6/24/2020 6:19pm
6/24/2020 6:19pm
Jbulz wrote:
It doesn't matter which coupler you're using. If you flash any of them to all 0's it will behave like the green one. If you plug...
It doesn't matter which coupler you're using. If you flash any of them to all 0's it will behave like the green one. If you plug in the black or white and read the fuel/ign tables you'll see the offset values for those couplers and the associated "Map 1/2/3" in the datastream screen.

I think Keefer made a mistake, because the map he posted is just the stock white one.
Cashmoney24 wrote:
Pretty sure that’s the same map that MXA has posted on their site and it seems to be the go to map for a lot of...
Pretty sure that’s the same map that MXA has posted on their site and it seems to be the go to map for a lot of owners as well. I could be wrong though.

Think you may have a point on the white coupler. MXA doesn’t say anything about which coupler to use. I can’t see why it would matter which one you are using as it is being rewritten.
Keefers is only slightly different on one of the maps. I can't remember if it was the ig or fi tho. Personally i went a little farther and pulled some timing out of the upper left corner for a little smoother power at small throttle opening or low rpm situations.
RF219
Profile picture for user RF219
Posts
210
Joined
4/1/2008
Location
USA
RF219 6/24/2020 7:25pm
6/24/2020 7:25pm
cmotodad wrote:
Any thoughts on 2020 KX450 forks? I am 180 lbs. with 5 hours on the bike. Feel like they are just getting a bit soft. Stock...
Any thoughts on 2020 KX450 forks? I am 180 lbs. with 5 hours on the bike. Feel like they are just getting a bit soft. Stock springs with 5cc more fluid per leg firm it up a bit? Thanks
stax199 wrote:
My riding gear was 23l bs!! FC wouldn't sell me my replacement springs until i weighed EVERYTHING. .. all agree increased sring rate will help alot.
datkin128 wrote:
So Stax, I just had pro circuit do my suspension. It needed a rebuild so I had them set it up while they were at it...
So Stax, I just had pro circuit do my suspension. It needed a rebuild so I had them set it up while they were at it. They did .53 springs in the front and a .57 (not sure if it’s .57 or 5.7) in the rear. Haven’t received it yet, but looking forward to more holdup on bigger hits.
datkin what is your weight and speed? those are the springs I am running also. I have been thinking about sending mine to them also.
datkin128
Profile picture for user datkin128
Posts
279
Joined
12/23/2015
Location
Lakewood, CO, USA
datkin128 6/24/2020 7:33pm
6/24/2020 7:33pm
RF219 wrote:
datkin what is your weight and speed? those are the springs I am running also. I have been thinking about sending mine to them also.
190 without gear and would call myself a Vet A rider. I need more holdup on the bigger hits if I mis-time something or Overjump a triple or whatever. Also need that vet comfort Smile I’ve heard they have good settings on this bike.
RF219
Profile picture for user RF219
Posts
210
Joined
4/1/2008
Location
USA
RF219 6/24/2020 7:52pm
6/24/2020 7:52pm
RF219 wrote:
datkin what is your weight and speed? those are the springs I am running also. I have been thinking about sending mine to them also.
datkin128 wrote:
190 without gear and would call myself a Vet A rider. I need more holdup on the bigger hits if I mis-time something or Overjump a...
190 without gear and would call myself a Vet A rider. I need more holdup on the bigger hits if I mis-time something or Overjump a triple or whatever. Also need that vet comfort Smile I’ve heard they have good settings on this bike.
we about the same, put up a ride report. I wanna try them but only hold up is probably gonna be 3 weeks to get it done by them, 2 weeks in shipping alone.
stax199
Profile picture for user stax199
Posts
157
Joined
3/7/2012
Location
Brooklyn, NY, USA
Fantasy
766th
stax199 6/26/2020 8:28am
6/26/2020 8:28am
cmotodad wrote:
Any thoughts on 2020 KX450 forks? I am 180 lbs. with 5 hours on the bike. Feel like they are just getting a bit soft. Stock...
Any thoughts on 2020 KX450 forks? I am 180 lbs. with 5 hours on the bike. Feel like they are just getting a bit soft. Stock springs with 5cc more fluid per leg firm it up a bit? Thanks
stax199 wrote:
My riding gear was 23l bs!! FC wouldn't sell me my replacement springs until i weighed EVERYTHING. .. all agree increased sring rate will help alot.
datkin128 wrote:
So Stax, I just had pro circuit do my suspension. It needed a rebuild so I had them set it up while they were at it...
So Stax, I just had pro circuit do my suspension. It needed a rebuild so I had them set it up while they were at it. They did .53 springs in the front and a .57 (not sure if it’s .57 or 5.7) in the rear. Haven’t received it yet, but looking forward to more holdup on bigger hits.
Nice.. im awaiting my factory connection springs.
Think they have sent same rates your calling out (i have to dbl check) and they go in sunday night so excited to ride with them. Being this heavy the bike wasnt terrible so should make big improvement.
centralcalmx 6/26/2020 5:25pm
6/26/2020 5:25pm
I finally gave up on Works chassis lab.
Zero response to Email and Messaging on Facebook.
Looking at some of the Facebook posts I guess I am far from being the only one that was disappointed with no response.
I just wanted an eta when they would be available.

I’m pretty patient and get these are not going to make me any faster but some basic communication would be helpful.
I went ahead and ordered a set from FCP.
Zero issues and one the road already.

I also bought a full set for my CRF from them to be fair with no issues at all.
2
centralcalmx 6/26/2020 5:26pm
6/26/2020 5:26pm Edited Date/Time 6/26/2020 5:48pm
quadzrulebro wrote:
Does anyone know of a screwdriver that works to adjust fork compression damping with 1 1/8th bars when the bar clamps are in the forward holes...
Does anyone know of a screwdriver that works to adjust fork compression damping with 1 1/8th bars when the bar clamps are in the forward holes? It is a PITA to have to remove the bars to adjust compression.
brandon_21888 wrote:
T[img]https://p.vitalmx.com/photos/forums/2020/06/24/434153/s1200_7E8DE58E_589E_4DD3_87FC_B3283A18CE15.jpg[/img] [img]https://p.vitalmx.com/photos/forums/2020/06/24/434154/s1200_22FFE3C7_E3CD_4DAD_A9C9_7EC46E63C2ED.jpg[/img] Got this off amazon... works perfect Neiko 01328A Low Profile Offset Screwdriver Set, 7 Piece | Portable Keychain Clip Included https://www.amazon.com/dp/B078MT1XQJ/ref=cm_sw_r_cp_api_i_a198EbPBQ58G9
T


Got this off amazon... works perfect

Neiko 01328A Low Profile Offset Screwdriver Set, 7 Piece | Portable Keychain Clip Included https://www.amazon.com/dp/B078MT1XQJ/ref=cm_sw_r_cp_api_i_a198EbPBQ58G9
Tbteam
Profile picture for user Tbteam
Posts
2869
Joined
8/16/2006
Location
Ormond Beach, FL, USA
Tbteam 6/26/2020 7:50pm
6/26/2020 7:50pm
Are we seriously 139 pages in just talking about 2019 KX450’s? 230k+ views? WTH is going on here?.. 😂
7
cody41
Profile picture for user cody41
Posts
518
Joined
4/25/2013
Location
Miami, FL, USA
cody41 6/27/2020 5:25am
6/27/2020 5:25am
Tbteam wrote:
Are we seriously 139 pages in just talking about 2019 KX450’s? 230k+ views? WTH is going on here?.. 😂
After 139 pages, I’m not convinced to purchase a kx450 unless I’m going to get rid of it at 45 hours.
1
7
cmotodad
Profile picture for user cmotodad
Posts
1009
Joined
12/18/2013
Location
Yorba Linda, CA, USA
cmotodad 6/27/2020 8:26am
6/27/2020 8:26am Edited Date/Time 6/27/2020 8:28am
If I was closer, you would be able to sell me yours at 45 hours. I bought a second hand 19 that had at least 90 hours. I know the original owner and between him and the 15 hours I put on it all that required changing was suspension fluids, chains, sprockets, guide and roller. Of course tires too. I now have a 2020 and it has been great so far.
2

Pit Row

See All »
Moto520
Profile picture for user Moto520
Posts
3666
Joined
2/4/2013
Location
Schaumburg, IL, USA
Moto520 6/27/2020 8:59am
6/27/2020 8:59am
brandon_21888 wrote:
T[img]https://p.vitalmx.com/photos/forums/2020/06/24/434153/s1200_7E8DE58E_589E_4DD3_87FC_B3283A18CE15.jpg[/img] [img]https://p.vitalmx.com/photos/forums/2020/06/24/434154/s1200_22FFE3C7_E3CD_4DAD_A9C9_7EC46E63C2ED.jpg[/img] Got this off amazon... works perfect Neiko 01328A Low Profile Offset Screwdriver Set, 7 Piece | Portable Keychain Clip Included https://www.amazon.com/dp/B078MT1XQJ/ref=cm_sw_r_cp_api_i_a198EbPBQ58G9
T


Got this off amazon... works perfect

Neiko 01328A Low Profile Offset Screwdriver Set, 7 Piece | Portable Keychain Clip Included https://www.amazon.com/dp/B078MT1XQJ/ref=cm_sw_r_cp_api_i_a198EbPBQ58G9
I bought one after reading this! It does work well
Moto520
Profile picture for user Moto520
Posts
3666
Joined
2/4/2013
Location
Schaumburg, IL, USA
Moto520 6/27/2020 9:01am
6/27/2020 9:01am
Tbteam wrote:
Are we seriously 139 pages in just talking about 2019 KX450’s? 230k+ views? WTH is going on here?.. 😂
cody41 wrote:
After 139 pages, I’m not convinced to purchase a kx450 unless I’m going to get rid of it at 45 hours.
They are solid. Easy stuff in the first ten hours and then no issues at all
lawson34
Profile picture for user lawson34
Posts
719
Joined
1/19/2019
Location
London, KY, USA
lawson34 6/27/2020 10:47am
6/27/2020 10:47am
Most haven't got over 45hours yet
kkawboy14
Profile picture for user kkawboy14
Posts
11486
Joined
6/5/2015
Location
USA
kkawboy14 6/27/2020 11:00am
6/27/2020 11:00am
Jbulz wrote:
It doesn't matter which coupler you're using. If you flash any of them to all 0's it will behave like the green one. If you plug...
It doesn't matter which coupler you're using. If you flash any of them to all 0's it will behave like the green one. If you plug in the black or white and read the fuel/ign tables you'll see the offset values for those couplers and the associated "Map 1/2/3" in the datastream screen.

I think Keefer made a mistake, because the map he posted is just the stock white one.
Cashmoney24 wrote:
Pretty sure that’s the same map that MXA has posted on their site and it seems to be the go to map for a lot of...
Pretty sure that’s the same map that MXA has posted on their site and it seems to be the go to map for a lot of owners as well. I could be wrong though.

Think you may have a point on the white coupler. MXA doesn’t say anything about which coupler to use. I can’t see why it would matter which one you are using as it is being rewritten.
RGaede wrote:
Keefers is only slightly different on one of the maps. I can't remember if it was the ig or fi tho. Personally i went a little...
Keefers is only slightly different on one of the maps. I can't remember if it was the ig or fi tho. Personally i went a little farther and pulled some timing out of the upper left corner for a little smoother power at small throttle opening or low rpm situations.
Can you post a screen shot of what you did?
Markopolo400
Profile picture for user Markopolo400
Posts
1431
Joined
7/24/2012
Location
St. Paul-ish, MN, USA
Markopolo400 6/27/2020 12:59pm
6/27/2020 12:59pm
lawson34 wrote:
Most haven't got over 45hours yet
I'm at 50. Still love my bike
1
cwolf96
Profile picture for user cwolf96
Posts
99
Joined
8/12/2019
Location
Delavan, WI, USA
cwolf96 6/27/2020 8:27pm
6/27/2020 8:27pm
How many hours is everyone getting out of their bottom chain roller? I shredded mine off in 23 hours. Curious if I should stick with OEM or if there’s a longer-lasting option.
Moto520
Profile picture for user Moto520
Posts
3666
Joined
2/4/2013
Location
Schaumburg, IL, USA
Moto520 6/27/2020 8:41pm
6/27/2020 8:41pm
cwolf96 wrote:
How many hours is everyone getting out of their bottom chain roller? I shredded mine off in 23 hours. Curious if I should stick with OEM...
How many hours is everyone getting out of their bottom chain roller? I shredded mine off in 23 hours. Curious if I should stick with OEM or if there’s a longer-lasting option.
Tm designworks or stock honda
1
quadzrulebro 6/28/2020 5:34am
6/28/2020 5:34am
cwolf96 wrote:
How many hours is everyone getting out of their bottom chain roller? I shredded mine off in 23 hours. Curious if I should stick with OEM...
How many hours is everyone getting out of their bottom chain roller? I shredded mine off in 23 hours. Curious if I should stick with OEM or if there’s a longer-lasting option.
Moto520 wrote:
Tm designworks or stock honda
TM Designworks for sure. It isn’t just a Kawasaki problem. My last bike was a Honda and I had to go to a Slide and Guide kit with chain rollers on that bike as well.
1
davidgrip
Profile picture for user davidgrip
Posts
273
Joined
10/7/2011
Location
Indianapolis, IN, USA
davidgrip 6/28/2020 5:39am
6/28/2020 5:39am
cwolf96 wrote:
How many hours is everyone getting out of their bottom chain roller? I shredded mine off in 23 hours. Curious if I should stick with OEM...
How many hours is everyone getting out of their bottom chain roller? I shredded mine off in 23 hours. Curious if I should stick with OEM or if there’s a longer-lasting option.
16-18 OEM Roller. 19-20 has one bearing, and the 16-18 has two bearings.
1
quadzrulebro 6/28/2020 5:53am
6/28/2020 5:53am
brandon_21888 wrote:
T[img]https://p.vitalmx.com/photos/forums/2020/06/24/434153/s1200_7E8DE58E_589E_4DD3_87FC_B3283A18CE15.jpg[/img] [img]https://p.vitalmx.com/photos/forums/2020/06/24/434154/s1200_22FFE3C7_E3CD_4DAD_A9C9_7EC46E63C2ED.jpg[/img] Got this off amazon... works perfect Neiko 01328A Low Profile Offset Screwdriver Set, 7 Piece | Portable Keychain Clip Included https://www.amazon.com/dp/B078MT1XQJ/ref=cm_sw_r_cp_api_i_a198EbPBQ58G9
T


Got this off amazon... works perfect

Neiko 01328A Low Profile Offset Screwdriver Set, 7 Piece | Portable Keychain Clip Included https://www.amazon.com/dp/B078MT1XQJ/ref=cm_sw_r_cp_api_i_a198EbPBQ58G9
Moto520 wrote:
I bought one after reading this! It does work well
Glad to hear it. Mine is coming via Amazon this week. I had to take my bars off to go two clicks stiffer this weekend 🤦🏼‍♂️
1
Nystrom7
Profile picture for user Nystrom7
Posts
282
Joined
8/17/2018
Location
SE
Nystrom7 6/28/2020 2:30pm
6/28/2020 2:30pm
lawson34 wrote:
Most haven't got over 45hours yet
78 on mine ☺️
DB505
Profile picture for user DB505
Posts
730
Joined
12/5/2013
Location
Rowlett, TX, USA
DB505 6/28/2020 5:25pm
6/28/2020 5:25pm
Anyone have issues with the bars twisting?

Post a reply to: Let's see/review those 2019 kx450s