What type of Vibration Dampening products do you use, if any?!?!?

swordfish
Profile picture for user swordfish
Posts
1950
Joined
9/2/2021
Location
Somewhere , AB CA
swordfish 9/30/2022 4:50am
9/30/2022 4:50am
TE Flex bars. Really more for taking the sting out of square edged stuff than vibration. I have a TPi so it’s pretty smooth to begin with.
1
motokiwi 9/30/2022 8:51am
9/30/2022 8:51am
Gimmick wrote:
I read an article in MxA back in the early 2000s . The guys were having trouble with vibrations on the new two strokes at the...
I read an article in MxA back in the early 2000s . The guys were having trouble with vibrations on the new two strokes at the time. They actually took a small piece of rubber about four inches long and half inch diameter and inserted into their rectum before going out to ride. The results were incredible: reduced vibrations while riding by around 70%
KTM riders have been using this trick for years
2
Zerofear66
Profile picture for user Zerofear66
Posts
1080
Joined
4/27/2017
Location
Anaheim, CA US
Zerofear66 9/30/2022 9:37am
9/30/2022 9:37am
holeshot413 wrote:
The fasstco fkex bars on my Honda AF Cr 500 work awesome and took out a lot of the buzz
This is exactly what I was looking for. I'm going to build an AF but the vibes ....😂

The Shop

See All »
Rider 5280
Profile picture for user Rider 5280
Posts
2392
Joined
11/9/2011
Location
Denver Metro, CO US
Rider 5280 9/30/2022 11:08am
9/30/2022 11:08am Edited Date/Time 9/30/2022 4:59pm
Gravel wrote:
I’m using 20 pounds of belly fat..
I just spit coffee all over my keyboard and screen. Eff'ing HILARIOUS.

Thank you, Fellow Fatty (although I might be carrying 30#s at this point .... 50% more than you!).
1
OldPro277
Profile picture for user OldPro277
Posts
1875
Joined
11/9/2009
Location
Avonmore, PA US
OldPro277 9/30/2022 11:38am
9/30/2022 11:38am
woodybepierced wrote:
Dumb Question . . . What type of foam do you put in the bars?!?!?!
I've used 1/2" diameter foam rubber (from McMaster-Carr) per advice from Billy at Luxon . Super cheap and definitely the best bang for you buck. That piece of $ 5 foam had a bigger affect than the $ 450 Mako bar clamps. But I used both on my Vintage Husky and I'm pleased. But doing it again, I'd just go the $5 McMaster-Carr route, lol
1
McG194
Profile picture for user McG194
Posts
4120
Joined
9/7/2017
Location
Palm Coast, FL US
McG194 9/30/2022 3:13pm
9/30/2022 3:13pm
Not really vibration dampening except for the real big vibrations but I run a Precision Racing Products steering damper on everything. You can solidly hit a tree and it absorbs enough that you are not crashing. I have one on my newer KTM and I have one for sale that fits a 4 stroke Yamaha that I'd probably take $250 for.
1
2
TeamGreen
Profile picture for user TeamGreen
Posts
36922
Joined
11/25/2008
Location
Thru-out, CA US
TeamGreen 9/30/2022 3:34pm
9/30/2022 3:34pm
A very well balanced crank-shaft.
4
Rider 5280
Profile picture for user Rider 5280
Posts
2392
Joined
11/9/2011
Location
Denver Metro, CO US
Rider 5280 9/30/2022 5:00pm
9/30/2022 5:00pm
woodybepierced wrote:
Dumb Question . . . What type of foam do you put in the bars?!?!?!
OldPro277 wrote:
I've used 1/2" diameter foam rubber (from McMaster-Carr) per advice from Billy at Luxon . Super cheap and definitely the best bang for you buck. That...
I've used 1/2" diameter foam rubber (from McMaster-Carr) per advice from Billy at Luxon . Super cheap and definitely the best bang for you buck. That piece of $ 5 foam had a bigger affect than the $ 450 Mako bar clamps. But I used both on my Vintage Husky and I'm pleased. But doing it again, I'd just go the $5 McMaster-Carr route, lol
Tell us more!

Can you give us the URL to the product?
Pro Lapse 9/30/2022 5:27pm
9/30/2022 5:27pm
Why would you want to damper vibration? Its the best part of the whole thing !
3
Langhammx 9/30/2022 6:07pm
9/30/2022 6:07pm
Herb Eaversmells wrote:
I have the Mako 360 on my Beta and the flexx bars on my YZ 250X. Both nice, flexx bar not as much room on the...
I have the Mako 360 on my Beta and the flexx bars on my YZ 250X. Both nice, flexx bar not as much room on the bars for all the switches, buttons, hand guards, lever, etc. Riding off road only, no tracks.





You do not ride, just stop…, Tongue
Luxon MX
Profile picture for user Luxon MX
Posts
1381
Joined
11/6/2017
Location
San Diego, CA US
Fantasy
57th
Luxon MX 9/30/2022 6:07pm
9/30/2022 6:07pm
woodybepierced wrote:
Dumb Question . . . What type of foam do you put in the bars?!?!?!
OldPro277 wrote:
I've used 1/2" diameter foam rubber (from McMaster-Carr) per advice from Billy at Luxon . Super cheap and definitely the best bang for you buck. That...
I've used 1/2" diameter foam rubber (from McMaster-Carr) per advice from Billy at Luxon . Super cheap and definitely the best bang for you buck. That piece of $ 5 foam had a bigger affect than the $ 450 Mako bar clamps. But I used both on my Vintage Husky and I'm pleased. But doing it again, I'd just go the $5 McMaster-Carr route, lol
Rider 5280 wrote:
Tell us more!

Can you give us the URL to the product?
You may have to alter the diameter based on your particular bars:

https://www.mcmaster.com/1298N7/
3
OldPro277
Profile picture for user OldPro277
Posts
1875
Joined
11/9/2009
Location
Avonmore, PA US
OldPro277 9/30/2022 6:35pm
9/30/2022 6:35pm
woodybepierced wrote:
Dumb Question . . . What type of foam do you put in the bars?!?!?!
OldPro277 wrote:
I've used 1/2" diameter foam rubber (from McMaster-Carr) per advice from Billy at Luxon . Super cheap and definitely the best bang for you buck. That...
I've used 1/2" diameter foam rubber (from McMaster-Carr) per advice from Billy at Luxon . Super cheap and definitely the best bang for you buck. That piece of $ 5 foam had a bigger affect than the $ 450 Mako bar clamps. But I used both on my Vintage Husky and I'm pleased. But doing it again, I'd just go the $5 McMaster-Carr route, lol
Rider 5280 wrote:
Tell us more!

Can you give us the URL to the product?
Easy to find. Go to McMaster.com , search “foam cord”, there are several types and sizes to choose from. I used the 5/8” white silicone . Measure the ID of your bars and get a size slightly larger,so it compresses. It’s a bit of a job to get it thru the bars fully. I found it easier to cut 4”- 6” sections to press in separately,use some lubricant and have a small diameter but semi stiff “pushrod” to push the foam cords in the bars. To test the theory, hang a set of bars from the ceiling and tap them with a wrench and hear and see the “ting” and vibration. Stuff a set with silicone cord and try the test again, you’ll be shocked how “dead” the bars become. Same effect on transmitting that vibration to you hands.
profeshenal125 9/30/2022 8:43pm
9/30/2022 8:43pm
The original and 1 and only RG3 4 rubber mount triple clamp. All Global 532LLc riders are required to run this component.




1
1
CarlinoJoeVideo
Profile picture for user CarlinoJoeVideo
Posts
7517
Joined
11/30/2013
Location
Portland/Los Angeles, CA US
CarlinoJoeVideo 9/30/2022 9:27pm
9/30/2022 9:27pm
I saw this on Thumber talk. Filling the ends of his bars with lead. I think it was a street bike.


McG194
Profile picture for user McG194
Posts
4120
Joined
9/7/2017
Location
Palm Coast, FL US
McG194 10/1/2022 12:24pm
10/1/2022 12:24pm
profeshenal125 wrote:
The original and 1 and only RG3 [img]https://p.vitalmx.com/photos/forums/2022/09/30/571455/s1200_567DF82A_09E2_4979_A226_0A0602E57036.jpg[/img]4 rubber mount triple clamp. All Global 532LLc riders are required to run this component. [img]https://p.vitalmx.com/photos/forums/2022/09/30/571459/s1200_13F143F4_5FF5_48AB_A693_2FE1AA00DFF6.jpg[/img] [img]https://p.vitalmx.com/photos/forums/2022/09/30/571457/s1200_C45497A5_E4BE_4ED1_8D90_68B0ED59184C.jpg[/img] [img]https://p.vitalmx.com/photos/forums/2022/09/30/571458/s1200_D643A6CB_11F0_4026_AF14_6747F9F5FF5E.jpg[/img] [img]https://p.vitalmx.com/photos/forums/2022/09/30/571456/s1200_45389EDC_6A29_4F3B_A17D_1C6292B82941.jpg[/img]
The original and 1 and only RG3 4 rubber mount triple clamp. All Global 532LLc riders are required to run this component.




Wowee Wow!! You have those bars rotated forward like a mother. I could never ride like that.
R VanKamp77
Profile picture for user R VanKamp77
Posts
499
Joined
8/15/2022
Location
Portland, TN US
R VanKamp77 10/1/2022 1:58pm
10/1/2022 1:58pm Edited Date/Time 10/1/2022 2:01pm
woodybepierced wrote:
Dumb Question . . . What type of foam do you put in the bars?!?!?!
OldPro277 wrote:
I've used 1/2" diameter foam rubber (from McMaster-Carr) per advice from Billy at Luxon . Super cheap and definitely the best bang for you buck. That...
I've used 1/2" diameter foam rubber (from McMaster-Carr) per advice from Billy at Luxon . Super cheap and definitely the best bang for you buck. That piece of $ 5 foam had a bigger affect than the $ 450 Mako bar clamps. But I used both on my Vintage Husky and I'm pleased. But doing it again, I'd just go the $5 McMaster-Carr route, lol
Sorry.. would you please provide a link? I’m pretty interested in this.

Edit: I see more now. Still, a link would be very appreciated too!

Edit: okay link acquired just ignore me lol

Pit Row

See All »
slipdog
Profile picture for user slipdog
Posts
10055
Joined
7/25/2009
Location
Nor Cal, CA US
slipdog 10/3/2022 9:06pm
10/3/2022 9:06pm
I have a pretty long story that I don't really feel like typing out and most of you don't want to read so if you're interested here's my TLDR version.

My 10yr old son started riding a '22 KTM 85 this summer. Have been riding it with K-tech spring conversion and Fasst co. flexx bars.

Decided to put the bike up for sale and removed the spring conversion and flexx bars to put on the new bike.

Used bike marked died and not one interested party after just over a month on CL and marketplace at a reasonable price so decided to start riding it again with a full motor rebuild in the very near future.

Figured I'd leave it listed for sale at first until I did the rebuild so we rode for the first time with the air forks and he didn't seem to notice any difference.

After a few rides, I noticed on the rougher track days he'd say he was getting tired by the end of the 3rd session(mini bikes get 4-20min sessions) and slow or pull off at 16-18min in the 4th session.

Normally he runs all 4-20 min sessions from start to checkers with no issue so I decided to put the spring conversion back in because even though he'd shrug his shoulders and say "it feels the same" I could see the air forks stood up much higher in the stroke and were twitchy on the main downhill at the Hangtown track, even at the minimum psi rating.

On the next ride at Hangtown with the spring kit, the bike looked much better and he was charging the downhill harder with no twitchiness like before even though he said "meh, feels the same". The only problem was by the end of the 3rd session his shoulders were getting sore again and he pulled off early in the 4th session because he was afraid he was going to crash.

Working on the bike last week the lightbulb went off that he was still riding with the Renthal Fat bars I put on in place of the flexx bars. The flexx bars went back on and we rode Saturday and Sunday at E st. MX which is a somewhat sandy track and it was a busy weekend so the track got more torn up than normal and by the end of the day it was choppier than Hangtown was the week before. At no point did he complain of being tired or pull off early and he actually had one of his better riding days in a while.

Take that for what you will but we will definitely be staying with the Fasst Co. flex bars for the foreseeable future.



P.S. When I asked him if he noticed any difference in the weight of the flexx bars he said "feels the same"

8
TeamGreen
Profile picture for user TeamGreen
Posts
36922
Joined
11/25/2008
Location
Thru-out, CA US
TeamGreen 10/3/2022 11:17pm
10/3/2022 11:17pm
slipdog wrote:
I have a pretty long story that I don't really feel like typing out and most of you don't want to read so if you're interested...
I have a pretty long story that I don't really feel like typing out and most of you don't want to read so if you're interested here's my TLDR version.

My 10yr old son started riding a '22 KTM 85 this summer. Have been riding it with K-tech spring conversion and Fasst co. flexx bars.

Decided to put the bike up for sale and removed the spring conversion and flexx bars to put on the new bike.

Used bike marked died and not one interested party after just over a month on CL and marketplace at a reasonable price so decided to start riding it again with a full motor rebuild in the very near future.

Figured I'd leave it listed for sale at first until I did the rebuild so we rode for the first time with the air forks and he didn't seem to notice any difference.

After a few rides, I noticed on the rougher track days he'd say he was getting tired by the end of the 3rd session(mini bikes get 4-20min sessions) and slow or pull off at 16-18min in the 4th session.

Normally he runs all 4-20 min sessions from start to checkers with no issue so I decided to put the spring conversion back in because even though he'd shrug his shoulders and say "it feels the same" I could see the air forks stood up much higher in the stroke and were twitchy on the main downhill at the Hangtown track, even at the minimum psi rating.

On the next ride at Hangtown with the spring kit, the bike looked much better and he was charging the downhill harder with no twitchiness like before even though he said "meh, feels the same". The only problem was by the end of the 3rd session his shoulders were getting sore again and he pulled off early in the 4th session because he was afraid he was going to crash.

Working on the bike last week the lightbulb went off that he was still riding with the Renthal Fat bars I put on in place of the flexx bars. The flexx bars went back on and we rode Saturday and Sunday at E st. MX which is a somewhat sandy track and it was a busy weekend so the track got more torn up than normal and by the end of the day it was choppier than Hangtown was the week before. At no point did he complain of being tired or pull off early and he actually had one of his better riding days in a while.

Take that for what you will but we will definitely be staying with the Fasst Co. flex bars for the foreseeable future.



P.S. When I asked him if he noticed any difference in the weight of the flexx bars he said "feels the same"

Best “write-up” I’ve read in a long, long time.

Thanks
1
R VanKamp77
Profile picture for user R VanKamp77
Posts
499
Joined
8/15/2022
Location
Portland, TN US
R VanKamp77 10/4/2022 12:17pm
10/4/2022 12:17pm
slipdog wrote:
I have a pretty long story that I don't really feel like typing out and most of you don't want to read so if you're interested...
I have a pretty long story that I don't really feel like typing out and most of you don't want to read so if you're interested here's my TLDR version.

My 10yr old son started riding a '22 KTM 85 this summer. Have been riding it with K-tech spring conversion and Fasst co. flexx bars.

Decided to put the bike up for sale and removed the spring conversion and flexx bars to put on the new bike.

Used bike marked died and not one interested party after just over a month on CL and marketplace at a reasonable price so decided to start riding it again with a full motor rebuild in the very near future.

Figured I'd leave it listed for sale at first until I did the rebuild so we rode for the first time with the air forks and he didn't seem to notice any difference.

After a few rides, I noticed on the rougher track days he'd say he was getting tired by the end of the 3rd session(mini bikes get 4-20min sessions) and slow or pull off at 16-18min in the 4th session.

Normally he runs all 4-20 min sessions from start to checkers with no issue so I decided to put the spring conversion back in because even though he'd shrug his shoulders and say "it feels the same" I could see the air forks stood up much higher in the stroke and were twitchy on the main downhill at the Hangtown track, even at the minimum psi rating.

On the next ride at Hangtown with the spring kit, the bike looked much better and he was charging the downhill harder with no twitchiness like before even though he said "meh, feels the same". The only problem was by the end of the 3rd session his shoulders were getting sore again and he pulled off early in the 4th session because he was afraid he was going to crash.

Working on the bike last week the lightbulb went off that he was still riding with the Renthal Fat bars I put on in place of the flexx bars. The flexx bars went back on and we rode Saturday and Sunday at E st. MX which is a somewhat sandy track and it was a busy weekend so the track got more torn up than normal and by the end of the day it was choppier than Hangtown was the week before. At no point did he complain of being tired or pull off early and he actually had one of his better riding days in a while.

Take that for what you will but we will definitely be staying with the Fasst Co. flex bars for the foreseeable future.



P.S. When I asked him if he noticed any difference in the weight of the flexx bars he said "feels the same"

I am having the exact same experience currently.
Thanks for sharing, I can add that to the radar.

Unrelated to the quote, I am going to plug and fill my bars with this stuff this weekend and see how it feels. Great price
https://www.amazon.com/dp/B07YWBXVND?psc=1&smid=A1YCMDUOW4P9DE&ref_=chk…
mxbarnhouse
Profile picture for user mxbarnhouse
Posts
4
Joined
12/24/2025
Location
YUMA, CO US
mxbarnhouse 2/19/2026 7:12pm
2/19/2026 7:12pm
slipdog wrote:
I have a pretty long story that I don't really feel like typing out and most of you don't want to read so if you're interested...
I have a pretty long story that I don't really feel like typing out and most of you don't want to read so if you're interested here's my TLDR version.

My 10yr old son started riding a '22 KTM 85 this summer. Have been riding it with K-tech spring conversion and Fasst co. flexx bars.

Decided to put the bike up for sale and removed the spring conversion and flexx bars to put on the new bike.

Used bike marked died and not one interested party after just over a month on CL and marketplace at a reasonable price so decided to start riding it again with a full motor rebuild in the very near future.

Figured I'd leave it listed for sale at first until I did the rebuild so we rode for the first time with the air forks and he didn't seem to notice any difference.

After a few rides, I noticed on the rougher track days he'd say he was getting tired by the end of the 3rd session(mini bikes get 4-20min sessions) and slow or pull off at 16-18min in the 4th session.

Normally he runs all 4-20 min sessions from start to checkers with no issue so I decided to put the spring conversion back in because even though he'd shrug his shoulders and say "it feels the same" I could see the air forks stood up much higher in the stroke and were twitchy on the main downhill at the Hangtown track, even at the minimum psi rating.

On the next ride at Hangtown with the spring kit, the bike looked much better and he was charging the downhill harder with no twitchiness like before even though he said "meh, feels the same". The only problem was by the end of the 3rd session his shoulders were getting sore again and he pulled off early in the 4th session because he was afraid he was going to crash.

Working on the bike last week the lightbulb went off that he was still riding with the Renthal Fat bars I put on in place of the flexx bars. The flexx bars went back on and we rode Saturday and Sunday at E st. MX which is a somewhat sandy track and it was a busy weekend so the track got more torn up than normal and by the end of the day it was choppier than Hangtown was the week before. At no point did he complain of being tired or pull off early and he actually had one of his better riding days in a while.

Take that for what you will but we will definitely be staying with the Fasst Co. flex bars for the foreseeable future.



P.S. When I asked him if he noticed any difference in the weight of the flexx bars he said "feels the same"

R VanKamp77 wrote:
I am having the exact same experience currently. Thanks for sharing, I can add that to the radar. Unrelated to the quote, I am going to...
I am having the exact same experience currently.
Thanks for sharing, I can add that to the radar.

Unrelated to the quote, I am going to plug and fill my bars with this stuff this weekend and see how it feels. Great price
https://www.amazon.com/dp/B07YWBXVND?psc=1&smid=A1YCMDUOW4P9DE&ref_=chk…

Any follow up with how that worked? 

1
Tokyo_Tiddler
Profile picture for user Tokyo_Tiddler
Posts
2122
Joined
7/25/2009
Location
Somewhere in, NJ US
Tokyo_Tiddler 2/19/2026 9:47pm
2/19/2026 9:47pm
MudPup545 wrote:
I have this video on my “watch later” list. I’m very interested in this system. My Beta 200 sends a lot of vibration through the bars.
I have this video on my “watch later” list.

I’m very interested in this system. My Beta 200 sends a lot of vibration through the bars.

The best remedy for vibration through the bars is Faasst Co's handlebar inserts. They absolutely work and I used them on my 2001 CR250 for years.  I also have a 2025 Beta 300 RX and I do not have any real vibration through the bars.

Tokyo_Tiddler
Profile picture for user Tokyo_Tiddler
Posts
2122
Joined
7/25/2009
Location
Somewhere in, NJ US
Tokyo_Tiddler 2/19/2026 9:49pm
2/19/2026 9:49pm
slipdog wrote:
I have a pretty long story that I don't really feel like typing out and most of you don't want to read so if you're interested...
I have a pretty long story that I don't really feel like typing out and most of you don't want to read so if you're interested here's my TLDR version.

My 10yr old son started riding a '22 KTM 85 this summer. Have been riding it with K-tech spring conversion and Fasst co. flexx bars.

Decided to put the bike up for sale and removed the spring conversion and flexx bars to put on the new bike.

Used bike marked died and not one interested party after just over a month on CL and marketplace at a reasonable price so decided to start riding it again with a full motor rebuild in the very near future.

Figured I'd leave it listed for sale at first until I did the rebuild so we rode for the first time with the air forks and he didn't seem to notice any difference.

After a few rides, I noticed on the rougher track days he'd say he was getting tired by the end of the 3rd session(mini bikes get 4-20min sessions) and slow or pull off at 16-18min in the 4th session.

Normally he runs all 4-20 min sessions from start to checkers with no issue so I decided to put the spring conversion back in because even though he'd shrug his shoulders and say "it feels the same" I could see the air forks stood up much higher in the stroke and were twitchy on the main downhill at the Hangtown track, even at the minimum psi rating.

On the next ride at Hangtown with the spring kit, the bike looked much better and he was charging the downhill harder with no twitchiness like before even though he said "meh, feels the same". The only problem was by the end of the 3rd session his shoulders were getting sore again and he pulled off early in the 4th session because he was afraid he was going to crash.

Working on the bike last week the lightbulb went off that he was still riding with the Renthal Fat bars I put on in place of the flexx bars. The flexx bars went back on and we rode Saturday and Sunday at E st. MX which is a somewhat sandy track and it was a busy weekend so the track got more torn up than normal and by the end of the day it was choppier than Hangtown was the week before. At no point did he complain of being tired or pull off early and he actually had one of his better riding days in a while.

Take that for what you will but we will definitely be staying with the Fasst Co. flex bars for the foreseeable future.



P.S. When I asked him if he noticed any difference in the weight of the flexx bars he said "feels the same"

R VanKamp77 wrote:
I am having the exact same experience currently. Thanks for sharing, I can add that to the radar. Unrelated to the quote, I am going to...
I am having the exact same experience currently.
Thanks for sharing, I can add that to the radar.

Unrelated to the quote, I am going to plug and fill my bars with this stuff this weekend and see how it feels. Great price
https://www.amazon.com/dp/B07YWBXVND?psc=1&smid=A1YCMDUOW4P9DE&ref_=chk…

Oh don't do that!  Guys tried doing that for the gen one CR's and it didn't work. Use the Faasst Co handlebar inserts. They work notably!

yamathumb
Profile picture for user yamathumb
Posts
199
Joined
3/11/2025
Location
Redding, CA US
yamathumb 2/19/2026 9:52pm
2/19/2026 9:52pm

You guys are weirdos

2
bvm111
Profile picture for user bvm111
Posts
10105
Joined
7/1/2008
Location
Las Vegas, NV US
bvm111 2/19/2026 10:47pm
2/19/2026 10:47pm

i’ve never used anything on any of my motorcycles since my 87 CR80… maybe i’m weird 

1
OwenJakes
Profile picture for user OwenJakes
Posts
1752
Joined
6/30/2023
Location
sebree, KY US
OwenJakes 2/20/2026 12:29am
2/20/2026 12:29am
slipdog wrote:
I have a pretty long story that I don't really feel like typing out and most of you don't want to read so if you're interested...
I have a pretty long story that I don't really feel like typing out and most of you don't want to read so if you're interested here's my TLDR version.

My 10yr old son started riding a '22 KTM 85 this summer. Have been riding it with K-tech spring conversion and Fasst co. flexx bars.

Decided to put the bike up for sale and removed the spring conversion and flexx bars to put on the new bike.

Used bike marked died and not one interested party after just over a month on CL and marketplace at a reasonable price so decided to start riding it again with a full motor rebuild in the very near future.

Figured I'd leave it listed for sale at first until I did the rebuild so we rode for the first time with the air forks and he didn't seem to notice any difference.

After a few rides, I noticed on the rougher track days he'd say he was getting tired by the end of the 3rd session(mini bikes get 4-20min sessions) and slow or pull off at 16-18min in the 4th session.

Normally he runs all 4-20 min sessions from start to checkers with no issue so I decided to put the spring conversion back in because even though he'd shrug his shoulders and say "it feels the same" I could see the air forks stood up much higher in the stroke and were twitchy on the main downhill at the Hangtown track, even at the minimum psi rating.

On the next ride at Hangtown with the spring kit, the bike looked much better and he was charging the downhill harder with no twitchiness like before even though he said "meh, feels the same". The only problem was by the end of the 3rd session his shoulders were getting sore again and he pulled off early in the 4th session because he was afraid he was going to crash.

Working on the bike last week the lightbulb went off that he was still riding with the Renthal Fat bars I put on in place of the flexx bars. The flexx bars went back on and we rode Saturday and Sunday at E st. MX which is a somewhat sandy track and it was a busy weekend so the track got more torn up than normal and by the end of the day it was choppier than Hangtown was the week before. At no point did he complain of being tired or pull off early and he actually had one of his better riding days in a while.

Take that for what you will but we will definitely be staying with the Fasst Co. flex bars for the foreseeable future.



P.S. When I asked him if he noticed any difference in the weight of the flexx bars he said "feels the same"

R VanKamp77 wrote:
I am having the exact same experience currently. Thanks for sharing, I can add that to the radar. Unrelated to the quote, I am going to...
I am having the exact same experience currently.
Thanks for sharing, I can add that to the radar.

Unrelated to the quote, I am going to plug and fill my bars with this stuff this weekend and see how it feels. Great price
https://www.amazon.com/dp/B07YWBXVND?psc=1&smid=A1YCMDUOW4P9DE&ref_=chk…
mxbarnhouse wrote:

Any follow up with how that worked? 

It worked pretty well. I checked and that link still works also. I felt like adding that to the bars was the best redneck fix you can do. On my RM-Z now I am just running PHDS mounts and that's the most effective in my opinion.

1
Timo
Profile picture for user Timo
Posts
1429
Joined
1/9/2021
Location
Wichita, KS US
Timo 2/20/2026 4:20am
2/20/2026 4:20am

I had carpal tunnel surgery and the vibrations are no longer an issue. 

Spoonguy
Profile picture for user Spoonguy
Posts
3475
Joined
2/28/2022
Location
Mc Kean, PA US
Spoonguy 2/20/2026 5:33am
2/20/2026 5:33am
swordfish wrote:
TE Flex bars. Really more for taking the sting out of square edged stuff than vibration. I have a TPi so it’s pretty smooth to begin...
TE Flex bars. Really more for taking the sting out of square edged stuff than vibration. I have a TPi so it’s pretty smooth to begin with.

100% I run them with Mako360 or PHDS mounts along with pillowtops and Scotts stabilizers.

Marty1028
Profile picture for user Marty1028
Posts
945
Joined
10/5/2017
Location
Lafayette, IN US
Marty1028 2/20/2026 5:50am
2/20/2026 5:50am
OldPro277 wrote:
I've used 1/2" diameter foam rubber (from McMaster-Carr) per advice from Billy at Luxon . Super cheap and definitely the best bang for you buck. That...
I've used 1/2" diameter foam rubber (from McMaster-Carr) per advice from Billy at Luxon . Super cheap and definitely the best bang for you buck. That piece of $ 5 foam had a bigger affect than the $ 450 Mako bar clamps. But I used both on my Vintage Husky and I'm pleased. But doing it again, I'd just go the $5 McMaster-Carr route, lol
Rider 5280 wrote:
Tell us more!

Can you give us the URL to the product?
Luxon MX wrote:
You may have to alter the diameter based on your particular bars:

https://www.mcmaster.com/1298N7/

Wont a bottle of spray foam do the same thing?

Post a reply to: What type of Vibration Dampening products do you use, if any?!?!?