Recent Activity
All
Wiscomx Added a reply to 2017 YZ125 Nikasil coating
7/12/2024 4:21am Your call, I would send it out to get repaired, might save you some headache and money in the long run
More »
Wiscomx Added a reply to WP 6500 internal cartridge oil capacity and service process
7/5/2024 4:43pm Fill with oil, measure down from top of tube, roughly 135mm down, insert base valve, some oil will push out during assembly.
Wiscomx Added a reply to titanium valves or stainless steel valves for kx250f?
7/3/2024 8:21pm No need for copper beryllium seat with stainless valves, it’s ideal for titanium valves, not so much for stainless, just get seats recut, don’t overlook guides either.
Wiscomx Added a reply to titanium valves or stainless steel valves for kx250f?
7/2/2024 8:49pm Stainless valves are fine, just get correct springs, and seats recut, they obviously are not as light as ti valves, at high rpm ss valves are very heavy and have a lot of mass compared to the ti version, with weight comes some issues, the big thing for valve life whether it is stainless or ti is a good clean...
Wiscomx Added a reply to One bike for Enduro/Offroad AND MX?
6/29/2024 6:53am Yamaha yz250fx or a 300 cc from one of the European manufacturers
Wiscomx Added a reply to Dubya edge wheel set reviews
6/17/2024 7:45pm I have a set, there the same as an excel notako rim, they hold up fine, I think the biggest is how true a wheel is and having even spoke tension is more of a factor then anything.
Wiscomx Added a reply to Fork Spring search by size
4/30/2024 7:12pm Diverse spring possibly, k-tech has a very good selection also
Wiscomx Added a reply to Ring end gap ?
4/3/2024 2:33pm Pull it apart and measure gaps, would hate for them to be tight and have issues, the gap is there for reason
Wiscomx Added a reply to Looking for 2011/12 kx250f head with cam cap
3/10/2024 7:14pm I might have one yet let me check in the morning
Wiscomx Added a reply to Timing conundrum
3/1/2024 8:57am Check orientation of tip over sensors, possibly when taken apart it was installed upside down
FGR01 Liked a reply to forum topic 2022 KTM 350SX-F New Cylinder Head Gasket failure?
2/20/2024 12:21pm
yeah, maybe try again with OEM and also check cylinder and head for flatness and have resurfaced. Note that layered metal gaskets required a pretty fine finish to seal correctly so make sure a reputable shop does the surfacing.
This forum topic has 2 replies.
Mucktub Liked a reply to forum topic Billy Bolt Super Pole
2/4/2024 6:54am
Mega
This forum topic has 44 replies.
Wiscomx Added a reply to What year is this YZ 250 engine?
1/9/2024 2:41pm 4xl is a 97’ model year https://www.bike-parts-yam.com/yamaha-motorcycle/search_vehicle/chassis
Wiscomx Added a reply to ProX Ti Valves
12/30/2023 4:13pm Kibblewhite titanium valves, or del west are very hard to beat, one piece is ideal, don’t skimp on valves
Wiscomx Started a new thread WTB 2021 and up AER 48 fork lugs
12/2/2023 1:36pm Looking for some WP Aer fork lugs, 21’ and newer
This forum thread has 2 replies.
Wiscomx Added a reply to Ditching No Toil, Branded air filter cleaner vs mineral spirits
10/29/2023 6:37pm The mineral spirits is really good, and affordable, earlier this year I fell for WR products filter cleaner, it works really good, I do not think you will get the 10 filters worth of cleaning out of it like they advertise, I would say mineral spirits or the wr cleaner, also switched to motul filter oil, so far seems like...
Wiscomx Started a new thread 2019 KTM 350 XCF
10/12/2023 6:25pm 350 XCF, new tires, foot pegs, remapped ecu, new pads, very well maintained, has 2023 aer forks, bladder conversion, 101 hrs, located in Wisconsin $5,300 262-six07-zero118
This forum thread has 0 replies.
Wiscomx Added a reply to Is this oil leaking through the Power Valve gasket?
9/24/2023 6:27am A lot of times the rod that runs thru to the power valve wears out seal and bore, sometimes a new seal works of drill bigger and install a bronze bushing, if it’s running fine just leave it.
Wiscomx Added a reply to 2022 ktm 150sx cylinder questions
7/4/2023 7:40am Measure cylinder or have a shop do it, I would assume you would be fine with an A size piston with the amount of hours you have on it, there is only .0008” between an a and b piston, a human hair is about .002 to .003” thou to put that into perspective, it’s pretty minimal, as far as honing...
Wiscomx Added a reply to Has anyone used a Mitaka cylinder?
6/27/2023 7:38pm Wisconsin,