Added reply in a thread 2018 CRF 250 R Water Pump Help 9/7/2020 3:01 AM

Didn't change shaft, changed only seals. Everything ok. Make close picture how water seal is placed on shaft, little bit wrong and it will leak. And be careful pressing in seal and shaft there is easy to damage water seal.

Added reply in a thread Crf 250 r 2018 stator 9/3/2020 6:00 AM

OEM part numbers are different

Added reply in a thread 2020 Crf250r. Anyone seen this before? 12/28/2019 1:25 AM

Maybe have to drill bigger holes in bracket? I don't see anything als could damage stud bolt

Added reply in a thread 2020 Crf250r. Anyone seen this before? 12/27/2019 7:55 AM

Maybe bracket change form when heated up and bend bolt?

Added reply in a thread 2020 Crf250r. Anyone seen this before? 12/27/2019 6:11 AM

The new one stud bolt (only one was bent) after some time was bent again on 2018 CRF250R not so badly as it was before when couldnt slide bracket off. Now with some force is possible to remove header without damaging bolt

Added reply in a thread What's everyone's preferred grips? 11/20/2019 2:37 AM

Pro Taper Pillow Top Lites

Added reply in a thread Estonia's Decade of MXoN Awesomeness! (and other cool stats I found...) 10/1/2019 3:51 AM

Population of Estonia is 1,3 million

Added reply in a thread Xtrig clamps 8/8/2019 3:24 AM

2017 CRF450R Xtrig is bolt on on 2015 CRF250R and 2018 CRF250R. Should be the same on 450

Added reply in a thread Quick Shifters 2/26/2019 10:46 AM

Not really racing I am road race mechanic. but yes, i am sometimes in Spain, Italy, Czech rep etc. In Slovakiaring once we share box with two fellows from Sweden. Or you are working in Wilo?

Added reply in a thread Quick Shifters 2/25/2019 6:04 AM

As I am from road racing I know benefit of quickshifter. Therefore had interest to install one on crosser. But dealer (friend) of one mentioned above company told me that on crosser QS don't work because if rear wheel spinning and you will shift (read ... more »

Added reply in a thread 2018 hard to start after mods 12/23/2018 3:20 AM

push button open full throttle for 2 sec and let it off all time pushing starter button. This is how I start when temperature is more then +25C (77F). Starts immediately. At cold have no problem

Added reply in a thread Quick turn throttle tubes. 11/12/2018 8:15 AM

I have one selves-made. Bought aluminium throttle tube with bearing added 1mm to radius (made aluminium ring, rework to fit throttle tube shape and glued it on with JB weld). Only on CRF250 2018 have to rework little bit front case part and with added ... more »

Added reply in a thread MXGP of Latvia - entries and preview 5/8/2018 9:46 AM

Track will be quite new for everyone because now it is turned clockwise

Added reply in a thread Pro Circuit Ti-6 Sytem for CRF 250 '18....HEAVY !! 3/6/2018 6:32 AM

Hey luckynino! Are CRF450 and CRF250 intake collectors interchangeable? Or is necessary to rework something?

Added reply in a thread Forum QNA: 2018 Vital MX 250 Shootout 11/7/2017 3:15 AM

ML told he has problems with this year KTM/Husky dyno and he took last years. But anyway if we take KTM torque graph and put in formula, HP numbers are different than in HP graph. For example at 13000 by formula we get only 39,6 but in graph 41,2. At ... more »

Added reply in a thread Forum QNA: 2018 Vital MX 250 Shootout 11/6/2017 11:45 PM

School. Physics. HP = NM x RPM / 7121 Take a look at Honda and KTM torque lines at 11 000. Them crosses. Take the formula and put same numbers in. Equals KTM has more ponies

smile
P.S. I've always been red ... more »
Added reply in a thread ACL replacement and recovery 11/2/2017 3:05 AM

Tore left knee ACL in ice hockey. Was back on ice after 5 months but not in full strength for games just for training. Fast recovery is more painful. Do all recovery program advised by sports doctors because for some average docs good enough is if you ... more »

Added reply in a thread How much fork spring preload? KX450F with önlins cartridges. 11/1/2017 1:16 AM

Will wait for spring and play with preload. Now due to whether ridable are only sand tracks and there I have no problems

Added reply in a thread How much fork spring preload? KX450F with önlins cartridges. 10/31/2017 3:51 AM

Here CRF250 2015 with Ohlins cartridges, 83kg, 4,7N/mm and 9mm preload. In mounting instructions is minumum preload 4mm, for my bike recommended 8-11mm. I like front end traction with this setup only maybe to harsh on small chops. Faster you go better

smile
... more »
Added reply in a thread 2018 CRF250R..any news? 10/26/2017 7:05 AM

:tumb up: