Fork bleeders

Rickyisms
Edited Date/Time 12/1/2020 2:48pm
Does anyone use the bleeders like this? I've been on the fence about ordering some as some people don't seem like too huge of fans of them, Worth it or not?
|
2WheelJocky 11/27/2020 9:33pm
11/27/2020 9:33pm
I just installed those exact ones. Ktm 250 xc-f 2019. 1 ride so far and worked great. Definitely easier than the screws that come stock.
Dimblewambie
Profile picture for user Dimblewambie
Posts
1528
Joined
1/28/2017
Location
Murrieta, CA, USA
Dimblewambie 11/27/2020 9:34pm
11/27/2020 9:34pm
I’ve got a set of the motion pros on a bike and they seem to work well without issue. I had a pair back in the day, don’t remember the brand but they seemed to suck air in while riding. YMMV.
mxaaron
Profile picture for user mxaaron
Posts
481
Joined
12/4/2007
Location
Richland, WA, USA
mxaaron 11/27/2020 9:34pm
11/27/2020 9:34pm
I use that exact set. They seem OK. I bought them because they are very short.
1
J-Mill
Profile picture for user J-Mill
Posts
181
Joined
7/11/2020
Location
Cottonwood, CA, USA
J-Mill 11/27/2020 9:45pm
11/27/2020 9:45pm
I used to use them but I run Pro-Taper (no cross bar) and I’ve had the bar pad push down and bleed them when I didn’t want it to. It’ll smoke your fork seals quick if you bleed them when the wheel is not off the ground. I’ve also smoked one riding in the woods and had to limp the bike back to the truck blowing oil out.... I went back to stock bleeder screws.

The Shop

See All »
Ryan625
Profile picture for user Ryan625
Posts
1689
Joined
9/14/2019
Location
Lynnwood, WA, USA
Ryan625 11/27/2020 10:01pm
11/27/2020 10:01pm
Not worth the risk. It isn’t hard to undo two screws even at a shitty angle 🤷🏻‍♂️
3
3
Bruce372
Profile picture for user Bruce372
Posts
6329
Joined
4/1/2008
Location
USA
Bruce372 11/27/2020 11:26pm
11/27/2020 11:26pm
I'd really like to drill and tap and countersink that silly M10 fork bleeder on the aer so you can run the torx m4 screw on both sides to bleed. Just don't have a drill press anymore
1
mattyhamz2 11/27/2020 11:43pm
11/27/2020 11:43pm
I have a set on my YZ250. Swapped out the other style bleeders because I hated them and the MP’s were cheaper than getting new OEM replacements. I’ve heard they are much better than the other style. I’ll report back as soon as I can ride a bit with these in.
soopah noviss 11/28/2020 4:14am
11/28/2020 4:14am Edited Date/Time 11/28/2020 4:17am
First thing I install on all my new bikes. Been running them for several years without issues....KYB, Showa and WP versions.

It's a farkin simple spring loaded needle valve. With all the electrical devices and mechanical components on these modern 4-strokes, the last thing I'm worried about failing is my fn fork bleeders.
3
llaliberte22 11/28/2020 4:36am
11/28/2020 4:36am
We have had those on three bike at a time ( 7or 8 different bike total) for about 10 years. Never had one failed, never had issues and they are way easier and faster to use than the screw. One of the first thing I put on a new bike.

We run the Zeta

1
MOTOXSTATION 11/28/2020 5:05am
11/28/2020 5:05am
I put on the Motion Pro’s ...no issues. It’s just way easier and faster like llaberte22 stayed above.
Tuna
Profile picture for user Tuna
Posts
1580
Joined
4/3/2017
Location
CA
Tuna 11/28/2020 7:07am
11/28/2020 7:07am
Bruce372 wrote:
I'd really like to drill and tap and countersink that silly M10 fork bleeder on the aer so you can run the torx m4 screw on...
I'd really like to drill and tap and countersink that silly M10 fork bleeder on the aer so you can run the torx m4 screw on both sides to bleed. Just don't have a drill press anymore
21 forks are M4 both sides now.
1
Bruce372
Profile picture for user Bruce372
Posts
6329
Joined
4/1/2008
Location
USA
Bruce372 11/28/2020 7:15am
11/28/2020 7:15am
Bruce372 wrote:
I'd really like to drill and tap and countersink that silly M10 fork bleeder on the aer so you can run the torx m4 screw on...
I'd really like to drill and tap and countersink that silly M10 fork bleeder on the aer so you can run the torx m4 screw on both sides to bleed. Just don't have a drill press anymore
Tuna wrote:
21 forks are M4 both sides now.
Yep. Ive got one of the bikes with updated forks as well.... that's why I had the idea.

I think the big 10mm bleeder is carryover from running two Schrader valves
1
Justin_P
Profile picture for user Justin_P
Posts
120
Joined
6/13/2019
Location
Hollis Center, ME, USA
Justin_P 11/28/2020 8:06am
11/28/2020 8:06am Edited Date/Time 11/28/2020 8:06am
I used motion pros this year, never had an issue over the course of 18ish hours. Kept the stockers in my toolbox just in case, but they worked fine.
ZOBITO
Profile picture for user ZOBITO
Posts
572
Joined
9/6/2020
Location
MX
ZOBITO 11/28/2020 10:04am
11/28/2020 10:04am
Some have a tendency to pump air in on rebound...
2
GeorgiePorgie 11/28/2020 10:09am
11/28/2020 10:09am
Had them on one of my bikes until I noticed oil started seeping out.
2
Patrick Potato 11/28/2020 10:52am
11/28/2020 10:52am
Cheap farkles that go well with anodized reservoir covers and spokeskins.
1
4
Rickyisms 11/28/2020 10:54am
11/28/2020 10:54am
GeorgiePorgie wrote:
Had them on one of my bikes until I noticed oil started seeping out.
That seems to be the consensus of them over time from what I have seen first hand.
Donkey Kong 11/28/2020 11:09am
11/28/2020 11:09am
I had a set of those a few years ago and they always leaked oil when I bled the forks
1

Pit Row

See All »
BobPA
Profile picture for user BobPA
Posts
8339
Joined
10/31/2013
Location
USA
BobPA 11/28/2020 12:32pm
11/28/2020 12:32pm
165 hours without fault on my 350. 80 hours on my 300 and still holding strong...
1
xrmark
Profile picture for user xrmark
Posts
1122
Joined
9/9/2019
Location
Lake Elsinore, CA, USA
xrmark 11/28/2020 12:36pm
11/28/2020 12:36pm
I have the same exact ones on my 17 crf450 and they work great haven’t had a problem yet
yzf162
Profile picture for user yzf162
Posts
259
Joined
6/23/2020
Location
Grant Park, IL, USA
yzf162 11/28/2020 2:45pm
11/28/2020 2:45pm
Call Ross over at enzo and ask him what he thinks about them. You'll get a earful! Lol
1
Goofball1205 11/28/2020 6:52pm
11/28/2020 6:52pm
I ran those for awhile but as others have said they always leaked oil when bleeding forks. Someone suggested the system tech racing bleeders. I've run them for 15+ hours so far and haven't had a drop of oil come out of them. They do advertise having a triple seal and seem to be a better design.
https://www.systemtechracing.com/Speed_Bleed_Button_p/10-01.htm
2
KurtJ99
Profile picture for user KurtJ99
Posts
2629
Joined
2/6/2017
Location
USA
KurtJ99 11/28/2020 7:05pm
11/28/2020 7:05pm
I’ve had several types. Some cheesy high profile broke or interfered with bars.
Latest Motion Pros have been pretty good low profile and recessed button so no accidental side loads/broken bleeders.
I habitually use them to bleed after tying down. I had a few chronic fork seals leak on my 03 CRF450 and a buddy suggested it would help. Yes, I know peak pressures when riding are higher. However haven’t had a fork seal leak since so I’ll keep doin it for all of my bikes since.
crusher773
Profile picture for user crusher773
Posts
2028
Joined
12/23/2009
Location
Coweta, OK, USA
crusher773 11/28/2020 7:16pm
11/28/2020 7:16pm
I've been running these things for like 20 years and never had an issue that includes all of our mini from the last about 7 years. I don't understand why anybody wouldn't run them.
1
MotoCoUSA
Profile picture for user MotoCoUSA
Posts
368
Joined
2/16/2018
Location
Colorado Springs, CO, USA
MotoCoUSA 11/29/2020 6:21am
11/29/2020 6:21am
I use the works connection shorty bleeders without issue
smv ryder
Profile picture for user smv ryder
Posts
889
Joined
11/2/2014
Location
Aspen, CO, USA
smv ryder 12/1/2020 2:48pm
12/1/2020 2:48pm
Goofball1205 wrote:
I ran those for awhile but as others have said they always leaked oil when bleeding forks. Someone suggested the system tech racing bleeders. I've run...
I ran those for awhile but as others have said they always leaked oil when bleeding forks. Someone suggested the system tech racing bleeders. I've run them for 15+ hours so far and haven't had a drop of oil come out of them. They do advertise having a triple seal and seem to be a better design.
https://www.systemtechracing.com/Speed_Bleed_Button_p/10-01.htm
IMO STR has a great product and work the best. They are also made in Colorado, so supporting local.

Post a reply to: Fork bleeders