Let's see/review those 2019 kx450s

Zeke27G
Posts
1412
Joined
11/8/2011
Location
Ascot Park, CA, USA
8/2/2020 6:40am
lawson34 wrote:
Zeke did u not like the ride engineering mount, I remember u had one for sale?
I have X-Trig clamps, so I didn’t need it. The Ride Mount came on my bike, I bought it used with 2.5 hours on it. I didn’t care for the fact that you can only run it in the rear mounting position and the extra bolts used to clamp the bars makes torqueing them a tedious process. If I ever go back to stock clamps, I’ll go with a Luxon bar mount.
2
datkin128
Posts
279
Joined
12/23/2015
Location
Lakewood, CO, USA
8/2/2020 7:10am
datkin128 wrote:
I haven’t unfortunately. Been busy with a lot of things lately. Want to get out soon. Was going to ride tomorrow, but weather might not be...
I haven’t unfortunately. Been busy with a lot of things lately. Want to get out soon. Was going to ride tomorrow, but weather might not be good. I at least plan to install in the bike this weekend lol.
RF219 wrote:
gotcha, I would like to hear what you think about it. I am debating who I wanna send mine to.
datkin128 wrote:
So I rode mine today for the first time with the PC suspension. It feels quite a bit different, but in a good way. I asked...
So I rode mine today for the first time with the PC suspension. It feels quite a bit different, but in a good way. I asked them to make it handle big hits and miscalculations better as my stock suspension didn’t give me a lot of cushion on bigger hits. It’s much stiffer now. There is a lot less pitching too. It still seems to handle the small chop quite well (which I also asked for). Now I’m able to hit bigger jumps without worrying so much if I don’t time it perfectly. I can definitely ride into stuff harder and don’t have to worry about it blowing through travel. Stiffer feeling for sure, but overall better I’d say.
I rode again yesterday and tested out the PC suspension a couple more times coming up short on the uphill triple at thunder valley before the finish line. Cased it pretty hard twice before clearing and my suspension soaked it up both times and let me have a controllable bounce instead of getting bucked. Exactly what I wanted!
2
8/2/2020 3:56pm
Whats everyone using for a sprockets. Tore up a renthal twin ring in 20 hours and i am very anal with keeping the chain adjusted correctly. Was going to go with a dirt tricks zirconium but they have been on back order.
OLDMOTO
Posts
467
Joined
3/20/2019
Location
San Diego, CA, USA
8/2/2020 4:02pm
Whats everyone using for a sprockets. Tore up a renthal twin ring in 20 hours and i am very anal with keeping the chain adjusted correctly...
Whats everyone using for a sprockets. Tore up a renthal twin ring in 20 hours and i am very anal with keeping the chain adjusted correctly. Was going to go with a dirt tricks zirconium but they have been on back order.
Supersprox dual rings. They last forever.
1

The Shop

davidgrip
Posts
273
Joined
10/7/2011
Location
Indianapolis, IN, USA
8/2/2020 4:30pm
Sunstar Works Sprockets and chains. Stock gearing with 116 link chain for longer wheel base.

Stock 114 link pictured.
8/2/2020 4:48pm
How are the sunstar works z?
bh
Posts
949
Joined
12/25/2016
Location
Piedmont, SC, USA
8/2/2020 4:56pm
Whats everyone using for a sprockets. Tore up a renthal twin ring in 20 hours and i am very anal with keeping the chain adjusted correctly...
Whats everyone using for a sprockets. Tore up a renthal twin ring in 20 hours and i am very anal with keeping the chain adjusted correctly. Was going to go with a dirt tricks zirconium but they have been on back order.
OLDMOTO wrote:
Supersprox dual rings. They last forever.
Mika metals chain and sprockets (hybrid steel/aluminum on the rear). Pretty nice especially with the othg discount. I’m running 13/51 with I believe 118 links.
1
thorns
Posts
723
Joined
4/25/2013
Location
NZ
8/2/2020 5:53pm
I know its not the ideal bike for it, but, all going to plan I am picking up a PW50 for the sons first bike this week. How will my 19 KX450 handle following him round at low speed once hes up and going ? Will it run way to hot?

Am I better to use it as an excuse to try upgrade to the new KX 450XC? Or will the bike be okay cruising round at pit speeds in 2nd gear?
davidgrip
Posts
273
Joined
10/7/2011
Location
Indianapolis, IN, USA
8/3/2020 7:08am
How are the sunstar works z?
Sunstar says that it is 3X stronger than stock and 10X stronger than Aluminum. For overall durability that is a Winner!
They recommend using with the XTG Chain.

mb60
Posts
5721
Joined
3/7/2010
Location
GRAPEVINE, TX, USA
8/12/2020 5:33pm
Have a question about replacing a 2019 kx 450 crankseal behind the stator ? Is the actual seal a bearing as well ?

And if so please tell me you don't have to split the cases to be replaced ?
MX683
Posts
46
Joined
1/25/2019
Location
Annandale, MN, USA
8/12/2020 5:44pm
mb60 wrote:
Have a question about replacing a 2019 kx 450 crankseal behind the stator ? Is the actual seal a bearing as well ? And if so...
Have a question about replacing a 2019 kx 450 crankseal behind the stator ? Is the actual seal a bearing as well ?

And if so please tell me you don't have to split the cases to be replaced ?
There is no seal behind the stator. What is the issue?
mb60
Posts
5721
Joined
3/7/2010
Location
GRAPEVINE, TX, USA
8/12/2020 6:09pm Edited Date/Time 8/12/2020 6:22pm
mb60
Posts
5721
Joined
3/7/2010
Location
GRAPEVINE, TX, USA
8/12/2020 6:21pm
MX683 wrote:
There is no seal behind the stator. What is the issue?
So there is no crankcase seal that you replace on these bikes ? Looks like it might be leaking from the crankshaft area behind the stator.
kkawboy14
Posts
11486
Joined
6/5/2015
Location
USA
8/12/2020 8:14pm
MX683 wrote:
There is no seal behind the stator. What is the issue?
mb60 wrote:
So there is no crankcase seal that you replace on these bikes ? Looks like it might be leaking from the crankshaft area behind the stator.
That area is supposed to have oil in it
mb60
Posts
5721
Joined
3/7/2010
Location
GRAPEVINE, TX, USA
8/12/2020 8:19pm
kkawboy14 wrote:
That area is supposed to have oil in it
So inside the actual cover there will be oil kawboy ?
kkawboy14
Posts
11486
Joined
6/5/2015
Location
USA
8/12/2020 8:27pm
kkawboy14 wrote:
That area is supposed to have oil in it
mb60 wrote:
So inside the actual cover there will be oil kawboy ?
Yes that’s how the electric start gears get oiled, unless I’m missing something.
mb60
Posts
5721
Joined
3/7/2010
Location
GRAPEVINE, TX, USA
8/12/2020 8:31pm
kkawboy14 wrote:
That area is supposed to have oil in it
mb60 wrote:
So inside the actual cover there will be oil kawboy ?
kkawboy14 wrote:
Yes that’s how the electric start gears get oiled, unless I’m missing something.
Well dam I need to research this more. Thanks for the info guys.
kkawboy14
Posts
11486
Joined
6/5/2015
Location
USA
8/12/2020 8:31pm
Behind this cover that the stator is bolted to there is oil



mxrose3
Posts
2381
Joined
8/17/2006
Location
Delmar, DE, USA
8/12/2020 10:38pm
mb60 wrote:
So inside the actual cover there will be oil kawboy ?
kkawboy14 wrote:
Yes that’s how the electric start gears get oiled, unless I’m missing something.
mb60 wrote:
Well dam I need to research this more. Thanks for the info guys.
Yeah, these aren't two strokes. Everything is oiled in the bottom end and top end. No two stroke type crank seals on either side.
ElliotB16
Posts
1135
Joined
6/10/2019
Location
Cairo, GA, USA
8/13/2020 8:01am
thorns wrote:
I know its not the ideal bike for it, but, all going to plan I am picking up a PW50 for the sons first bike this...
I know its not the ideal bike for it, but, all going to plan I am picking up a PW50 for the sons first bike this week. How will my 19 KX450 handle following him round at low speed once hes up and going ? Will it run way to hot?

Am I better to use it as an excuse to try upgrade to the new KX 450XC? Or will the bike be okay cruising round at pit speeds in 2nd gear?
I rode with my kid this past weekend. A pitbike would be much better. It was 1st gear and lots of clutching to ride with him
cwolf96
Posts
99
Joined
8/12/2019
Location
Delavan, WI, USA
8/13/2020 7:18pm
I need some help.... can anyone tell me which way the seals face on the piston for the rear master cylinder? I blew my seals this week, ordered an All Balls Rebuild Kit and now questioning which way they should face on the piston.
motoxxx599
Posts
3195
Joined
11/18/2008
Location
Sachse, TX, USA
8/13/2020 7:55pm
Got a quote from PC today for A Kit Suspension - $11,800. Includes clamps. Yikes!
1
D_Mash336
Posts
132
Joined
5/16/2018
Location
USA
8/13/2020 8:05pm
motoxxx599 wrote:
Got a quote from PC today for A Kit Suspension - $11,800. Includes clamps. Yikes!
Holy cow
datkin128
Posts
279
Joined
12/23/2015
Location
Lakewood, CO, USA
8/13/2020 8:08pm
motoxxx599 wrote:
Got a quote from PC today for A Kit Suspension - $11,800. Includes clamps. Yikes!
Lol I hope u r suuuuuper fast!
coastie44
Posts
566
Joined
1/19/2013
Location
NorCal, CA, USA
8/13/2020 9:09pm Edited Date/Time 8/13/2020 11:08pm
motoxxx599 wrote:
Got a quote from PC today for A Kit Suspension - $11,800. Includes clamps. Yikes!
Save yourself the coin, I bought the Technical Touch KYB factory kit forks and shock for my '17 bike. The forks are amazing and were about $4500 all in! I did send the forks over to Enzo for a slightly softer revalve and they nailed it.

I moved the forks over to my '19 KXF but the shock doesn't fit so it is still on the '17. I did tweak the stock shock settings a fair amount, but now when I ride the two bikes back-to-back I honestly cant tell the difference between the stocker on the ‘19 and the expensive KYB factory shock on the ‘17. I think the KYB factory shock needs a revalve to be a touch softer, but given the performance of the stocker on the '19, I don't even think I'll have it revalved.

TL;DR expensive as f!ck kit forks are worth it. Shock isn’t.
Cashmoney24
Posts
36
Joined
3/7/2020
Location
Harpers Ferry, WV, USA
8/14/2020 3:16am
motoxxx599 wrote:
Got a quote from PC today for A Kit Suspension - $11,800. Includes clamps. Yikes!
Wow..that’s gone up quite a bit. I bought a set with clamps from PC in 04 for my crf 250, and it was like $5,500 for everything. Stuff was pretty awesome though... definitely not fast enough to appreciate it though.
motoxxx599
Posts
3195
Joined
11/18/2008
Location
Sachse, TX, USA
8/14/2020 11:28am
motoxxx599 wrote:
Got a quote from PC today for A Kit Suspension - $11,800. Includes clamps. Yikes!
datkin128 wrote:
Lol I hope u r suuuuuper fast!
Lol not 11k for suspension fast that's for sure!
2
Mr. Afterbar
Posts
2431
Joined
5/13/2019
Location
Green Bay, WI, USA
8/20/2020 6:01am
I have almost 5 hours on my ‘21 now and finally got to a track worthy of shaking it down. I’m coming off a ‘16 KX 450. The suspension is way under sprung for me front and rear as expected. Currently 210 lbs 35 year old expert. The bike is more hesitant to lean over in corners than my ‘16. All I’ve done so far is raise the forks to the first mark and set the sag. The rear brake is too touchy for my liking. Tapping it going into tight corners lets out a nice squeal and is too grabby. The engine feels great and the clutch is amazing. One spot in particular at the track I most recently rode, I could feel the clutch slipping on my ‘16 every time. No issue on the ‘21. I had my reservations about the hydraulic clutch as I’ve always preferred the feel of a cable, but it works good out on the track. Looking forward to getting some stiffer springs on this thing and getting it fine tuned to my liking. Not sure what I’m going to do with the rear brake yet if anything at all. I may just try adjusting the pedal down a bit.


2
2
Cashmoney24
Posts
36
Joined
3/7/2020
Location
Harpers Ferry, WV, USA
8/20/2020 6:17am
Thanks for the review... a lot of people have gone with the rear caliper hanger and rotor off of the 2018. I did that myself and it worked pretty well. Can probably score the new parts off eBay at a good discount.
1
mxb2
Posts
22435
Joined
6/15/2010
Location
Bowie, MD, USA
8/20/2020 6:30am
I have almost 5 hours on my ‘21 now and finally got to a track worthy of shaking it down. I’m coming off a ‘16 KX...
I have almost 5 hours on my ‘21 now and finally got to a track worthy of shaking it down. I’m coming off a ‘16 KX 450. The suspension is way under sprung for me front and rear as expected. Currently 210 lbs 35 year old expert. The bike is more hesitant to lean over in corners than my ‘16. All I’ve done so far is raise the forks to the first mark and set the sag. The rear brake is too touchy for my liking. Tapping it going into tight corners lets out a nice squeal and is too grabby. The engine feels great and the clutch is amazing. One spot in particular at the track I most recently rode, I could feel the clutch slipping on my ‘16 every time. No issue on the ‘21. I had my reservations about the hydraulic clutch as I’ve always preferred the feel of a cable, but it works good out on the track. Looking forward to getting some stiffer springs on this thing and getting it fine tuned to my liking. Not sure what I’m going to do with the rear brake yet if anything at all. I may just try adjusting the pedal down a bit.


Compared to the 2016? Pros ,cons. Motor, ergos, package. Better, way better. Or. Just different. Thanks.

Post a reply to: Let's see/review those 2019 kx450s

The Latest