Added reply in a thread 2 Strokes are dead!? 8/27/2019 8:32 PM

I converted to a 4 stroke several years ago. I still own many 2 strokes but my main bike I ride is a 4 stroke. I am thinking of getting the new KTM XC250TPI? Any thoughts

Added reply in a thread 18 Husky 350 Wont start 8/18/2019 7:24 PM

Did you try the reset I mentioned?

Added reply in a thread 18 Husky 350 Wont start 8/14/2019 9:43 PM

I had a very similar issue. Disconnect the battery cables and hold them together, not touching the battery for 1 minute. Supposedly this should rest the ECU. It worked on my bike. I chased wires, changed battery, fuel pump, filters, fuses..... Nothing ... more »

Added reply in a thread Fox Factory Forx goodies 7/29/2019 8:56 PM

Yes, one of these would probably work as well. Already have the Husky cable guide coming. If I cannot get it to work, this will be the next option. Thanks

Added reply in a thread refurbishment of white yz80 tank 7/22/2019 8:05 PM

That worked on that piece. Just need a big clear bag that seals for the tank.

Added reply in a thread Fox Factory Forx goodies 7/22/2019 7:59 PM

Thanks for the tip. I will look into that.

Added reply in a thread Cool stuff from your childhood! 7/21/2019 9:45 PM

A few items .

Added reply in a thread refurbishment of white yz80 tank 7/21/2019 9:06 PM

I didn't read it all. I see you are trying the bleach. Hope it works.

Added reply in a thread refurbishment of white yz80 tank 7/21/2019 9:04 PM

I have not tried it but, what about bleach? White tank, may work? I done a few tanks. I have used the head light renew kit. Works pretty good. Takes a bit of time. I also made a "dummy backbone" for lack of better term with 2x4's to hold the tank while ... more »

Added reply in a thread Fox Factory Forx goodies 7/21/2019 8:56 PM

Does anyone know of a front brake cable guide that will bolt to the lower triple clamp on the FFF? I just put a set on my CR250 and the stock guide will not fit on the lower clamp. The stock upper clamp will fit on the FFF upper. Looking for ideas. Thanks ... more »

Added reply in a thread MXGP of Asia 7/14/2019 6:03 AM

To me I saw a race with no spectators and both classes with 1/2 gates filled. Looks pretty sad from where I am sitting. Is MXGP declining or is this because the race was in Indonesia? How much longer can they continue with no riders and no spectators. ... more »

Added reply in a thread Best commentators around 6/24/2019 8:46 PM

I say bring back Bailey

Added reply in a thread 1980 Yamaha YZ50 Exhaust Pipe 6/16/2019 12:24 PM

Started new thread 1980 Yamaha YZ50 Exhaust Pipe 6/16/2019 12:23 PM

This pipe is for a 1980 YZ50, no silencer. $75.00 plus shipping

... more »

This forum thread has 3 replies

Started new thread 1980 Yamaha YZ125 parting out 6/16/2019 12:19 PM

Frame $100 Swingarm $75 Motor complete and rebuilt $400 Forks and triple clamps $125 Front hub with brake plate $75 Rear hub with brake plate $75 Air box $80 Seat, new cover $150 Tank with decals $200 Carb $50 CDI & Coil $60

... more »

This forum thread has 1 reply

Added reply in a thread For Sale: 1978 RM125C 6/10/2019 10:54 PM

Did you post in “Moto related” asking the same question with a picture of a different bike? Which bike is for sale? Are they both yours? Both for sale? Both have fox heads? Nice bikes

Added reply in a thread Vitalmx stats through the years 5/18/2019 5:03 PM

I guess i didn't explain myself very well. When I said the posts above, I meant the previous posts that were negative to soren346. I was complimenting your post.

Added reply in a thread Vitalmx stats through the years 5/18/2019 7:19 AM

Yes, this platform makes a lot of people say things they typically wouldn't say to a person if they were standing in front of them.

Added reply in a thread Vitalmx stats through the years 5/18/2019 7:00 AM

In my small opinion, these posts make it good/fun. The negative posts (which you see above) take over every discussion, quickly. Which is a turn off for me and why I don't bother posting or commenting much. But I am a nobody. There was a post specifically ... more »

Added reply in a thread Zach Osborne setting Holeshot Device 5/6/2019 8:50 PM

I saw a video of Ty Masterpool doing this a few years back also, cool little trick. The guys in the videos above make it look so easy.