Recent Activity
All
hillbilly Liked a reply to forum topic Budds Creek law suit
3/12/2020 7:46am
A country where they ride flip flops or a stray camel doesn't count.
This forum topic has 183 replies.
Indy mxer Liked a reply to forum topic Budds Creek law suit
3/12/2020 7:44am
Yes, they are for profit companies Einstein. Who the hell didn't know that. But you're also full of shit on much of what you say. I've had Blue Cross/Blue Shield thru 2 jobs I've worked over the past 30 years. Not once have I had anything, not one thing, turned down. And I've had my share of surgeries, mri's, concussions, breaks and injuries. And not once did they sue! Now are there a few bad insurance companies? Yes. But to paint with such a broad brush is ignorant of the facts. Which it's obvious you are. Oh and btw, our...
This forum topic has 183 replies.
MX683 Added a reply to Let's see/review those 2019 kx450s
8/7/2019 10:27am I tried it and thought it cornered better. The front end didn't "lift" as easily. Although, later I was looking for better rear wheel traction and ended up taking the extra link back out to shorten back to where it was. Overall I was happier with the shorter wheelbase. I didn't notice any stability difference either way.
MX683 Added a reply to kx250 upgrade to 250f suspension anyone done it?
5/7/2019 9:41am I have done it. I used the entire front end from an 2009 kx250f. I also used a 2009 ohlins shock on the rear, but, had to make different linkage. I didn't like the stock linkage anyway,because the last portion of travel wasn't actually "rising rate"
MX683 Added a reply to Back to the drawing board for Yamaha?
3/9/2019 8:41pm I think that his taking the boot off is an indication of an ankle injury. I have had it where I took my boot off before the ankle started swelling and getting more tender...making boot removal very difficult.
MX683 Added a reply to Let's see/review those 2019 kx450s
2/15/2019 5:43am DID 520 MX chain lasts way longer. DID has a chart with the tensile strength numbers for their chains. After you get a lot of use out of it, what usually ends it’s life is a roller will go missing.
MX683 Added a reply to Let's see/review those 2019 kx450s
2/14/2019 4:18pm I have run my 17, 18 and 19 way forward and noticed and liked extra rear wheel traction on accell
MX683 Added a reply to Minneapolis Weather
2/8/2019 10:59am Great! We could sure use some of it here in Minnesota.
MX683 Added a reply to Minneapolis Weather
2/8/2019 6:51am sure could use some global warming...more than the .1 degrees every 50 years that we have been getting.
MX683 Added a reply to Let's see/review those 2019 kx450s
2/8/2019 6:24am I tried an ohlins shock that fit my 2018 and it won’t fit my 2019. It looked like it might work, but reservoir hit the frame.
MX683 Added a reply to Let's see/review those 2019 kx450s
1/26/2019 8:01pm Off-road 175 lbs .46 fork springs, softer fork compression valving, faster fork rebound valving and way more mid valve float . In the rear softer compression valving and faster rebound valving. Ignition mapping retarded 3 degrees at just off idle through 60 degree throttle opening. Best move map set point from 10 degrees to just above closed throttle. One or...
MX683 Added a reply to Will KX450F 2018 Triple Clamps fit on 2019 KX450???
1/26/2019 8:26am I took a better look at my top neken clamp and there are 3 threads exposed above the nut, so oem nut and washer would have worked. I also measured the height of the clamps at the stem and both are identical (20mm). So, wouldn't I have the same flush starting point for tube height? (both clamps are even across...
MX683 Added a reply to Will KX450F 2018 Triple Clamps fit on 2019 KX450???
1/25/2019 5:18pm I swapped my neken clamp from 2018 kx450f onto 2019 kx450 and it fit perfectly, with an aftermarket nut with a flange on it, instead of oem nut and thick washer.