Added reply in a thread 2019 KTM 450 SX-F CP-Carrillo Piston Kit - Where to Buy?!?! 10/27/2021 9:24 PM

Check here https://ktm-versand.de/en/ European website I ordered an Oem piston kit for my 350, saving 100-200 over anywhere in the states. Shipping was fairly cheap and fast

Added reply in a thread 2021 KX250 8/20/2021 8:14 AM

If only the parts weren’t on back order …

Added reply in a thread Let's see/review those 2019 kx450s 8/5/2021 1:34 PM

I’m 6’ prefer them on the standard position myself. I ran them in the lower position for a while but the pegs were collecting a lot of dirt on deep rutted days, so I moved them back up it didn’t make a huge difference they still pack with dirt but it’s ... more »

Added reply in a thread 2021 KX250 5/10/2021 2:38 PM

No problems here with the full FMF. I do starts sitting pretty neutral on the seat not too far forward, with both feet down just in front of the pegs

Added reply in a thread 2021 KX250 5/1/2021 1:06 PM

Got er looking pretty good anyway

... more »
Added reply in a thread 2021 KX250 5/1/2021 12:53 PM

When you dump in 800 ml without filter change

And 16 hard hours on the stock clutches I must be playing with fire 😆🤞🏼
Added reply in a thread 2021 KX250 4/29/2021 12:14 PM

Are you guys doing as the manual says ? Put in the specified amount of oil, let the bike idle for a few minutes, then shut off wait a few minutes and check sight glass level with bike on level ground. I follow the manual and it is about spot on, sometimes ... more »

Added reply in a thread 2021 KX250 4/5/2021 6:14 AM

Yes, I ran the stock 100 3s, a 110 mx52, and now a fresh 110 33. Think I prefer the 110 not much a difference though

Added reply in a thread 2021 KX250 4/4/2021 11:06 AM

This bike handles like an absolute dream after a revalve from Enzo, the FMF system maybe added some more mid to top, but mainly sounds and looks a whole lot nicer. Stock mapping with green coupler. Would really like to pull the trigger on a ... more »
Added reply in a thread Seat Bounce 3/3/2021 9:11 AM

Inexperienced Riders seem to have this misconception that seat bouncing will throw you into a mega endo unless being compensated by yanking back on the bars ... then you seem them riding a signature Ronnie Mac air wheelie

laughing
if the bike is working ... more »
Added reply in a thread Let's see/review those 2019 kx450s 2/13/2021 7:54 AM

A simple method I use after adjusting a chain, pull the bike off the stand and sit on it the here the chain should have a bit of slack but not much and definitely not like a banjo string

Added reply in a thread 2021 KX250 2/13/2021 7:40 AM

I can’t comment on the FMF yet, will likely be a bit before I get to ride it. On the fence whether to have the stock ECU tuned or pull the trigger on a vortex...

Added reply in a thread 2021 KX250 2/10/2021 4:43 AM

Looking much better

Added reply in a thread 2021 KX250 2/6/2021 5:50 PM

Nice to hear 👍🏼 I’ve got a full stainless system arriving soon

Added reply in a thread 2021 KX250 1/28/2021 2:32 PM

Gonna be tough to find comfort out of the stock setup for you guys around 150 lb IMO. Likely need atleast lighter fork springs and revalve front and rear.

Added reply in a thread Forkner “stupidity”? 1/22/2021 1:47 PM

I guess you really can’t fix stupid

Added reply in a thread KYB PSF1 in a YZ? 1/14/2021 8:48 PM

Correct me if I’m wrong but either of these won’t work, when your fork compresses the air chamber gets smaller causing the pressure to go up this is what gives the air spring it’s progressiveness. In order for a bleeder to work it would have to know ... more »

Added reply in a thread Let's see/review those 2019 kx450s 1/12/2021 9:32 AM

My buddy had a similar issue with his yz450f ti 4.1 slip on, pretty sure he sent it back to fmf and they repaired/replaced

Added reply in a thread Let's see/review those 2019 kx450s 1/3/2021 8:05 AM

I’ve been using maxima. In my opinion it seems like the setup doesn’t seal very well considering others are having the same issues. A buddy I know has put 75-100 hours on 3 newer ktms without ever even taking apart the steering assembly and never had ... more »

Added reply in a thread Let's see/review those 2019 kx450s 1/3/2021 7:18 AM

I have a 21 kx250 and greased them after the first ride, after only 10 hours the steeering was starting to get notchy. Tore into it yesterday and the upper bearing had been a little contaminated/rusty the lower wasn’t bad. I was able to clean up the ... more »