Started new thread Runaway 2 stroke engine 10/31/2017 3:54 PM

Last year I had put my 05 rm125 back together after sitting for a long time and took it out for a spin for about 30 minutes until the engine ran away on me. Kicked the bike into gear and held the brake and stalled the engine. So anyways my dumb ass didn't ... more »

This forum thread has 4 replies

Added reply in a thread 2017 sxf450 front axle/fork issue 11/24/2016 7:24 AM

It's not the air side

Added reply in a thread 2017 sxf450 front axle/fork issue 11/24/2016 6:55 AM

It's not the air side it's the other side

Started new thread 2017 sxf450 front axle/fork issue 11/23/2016 8:50 PM

Just doing some maintenance on my bike, took it all apart for regreasing, etc. Put the forks back on nice and even then when I go to put my front wheel back on the axle doesn't want to slide though easily because one of the forks is sitting higher then ... more »

This forum thread has 8 replies

Started new thread Anyone have an rm125 motor!? 11/18/2016 8:29 AM

Starting another 125 build got a solid start to the project but no motor. Anyone have an rm125 motor 2004 or newer they wanna sell? Running or not.

This forum thread has 1 reply

Added reply in a thread What kind of oil in 2016/17 sxf450 8/28/2016 11:08 AM

Heard of too many bad stories with the rotella, but there is quite a few people who swear by it.

Started new thread What kind of oil in 2016/17 sxf450 8/28/2016 9:38 AM

What kind of oil are you guys running in your bikes? Been hearing lots of things about running 10w60 over the recommended 10w50

This forum thread has 11 replies

Started new thread When I start my bike it goes on runaway (stays wide open) 8/11/2016 8:51 PM

Just changed clutch fibers and plates, put it all back together, go to start it and it just stays wide open had to slam it into gear and hold my foot on the brake. Anyone have any idea why it does this?

This forum thread has 6 replies

Started new thread 1987 cr80 runs like shit 8/11/2016 12:20 PM

Just picked up a 1987 cr80 for dirt cheap cause it runs like shit. The bike wont open up at all. Idles fine and sounds good at idle and feel like it has good compression but when you open up the throttle it just won't hit the power. I pulled the carb ... more »

This forum thread has 3 replies

Started new thread Someone sell me on the 2017 TC250 7/20/2016 7:41 PM

I'm on the market for a new bike and I wanna go white. Was originally thinking of going with the FC350 but having second thoughts. Who ever on here has one maybe try to convince me to buy one haha

This forum thread has 13 replies

Added reply in a thread How reliable are the new 2 strokes? 7/20/2016 7:35 PM

Bought them both used. My 250 hasnt actually been all that bad but it's been having some tranny problems and im just getting tired of it. When i bought it every bolt on the bike was stripped, i could count on one finger how many bolts weren't stripped ... more »

Added reply in a thread How reliable are the new 2 strokes? 7/20/2016 7:04 PM

When did I say I didn't open it up? I cracked I pulled the head off twice and never found a reason to spend money on a rebuild kit, just throw some new seals on and put it back together. I actually do maintenance, regreasing ect. not just soak my bikes ... more »

Started new thread How reliable are the new 2 strokes? 7/19/2016 10:59 PM

The last few 2 strokes I've had, all been Suzuki's, just havnt been reliable for me. Problem after problem, but I do love the bikes but I'm just scared to keep testing my luck with used ones. Brand new 2011 rmz450 lasted me 135 hours on the original ... more »

This forum thread has 13 replies

Added reply in a thread How do they get all these motors clean on these "builds"!!! 7/19/2016 10:48 PM

Time time time and Scotch Brite

Added reply in a thread RM Triple Clamp Advice/Reducing Triple Clamp Offset 6/6/2016 3:42 PM

I got stock offset with my ride clamps for mine.

Added reply in a thread RMZ subframe on RM??? 6/5/2016 10:08 PM

No real advantage at all, I just like the modern look and I think its cool to have something different than all the other RM's. Performance is obviously the most important part about a bike but I still love to stare at them.

Added reply in a thread RMZ subframe on RM??? 6/2/2016 10:02 AM

Alright well I'll to a quick test fit from my buddy's rmz250

Added reply in a thread RMZ subframe on RM??? 6/1/2016 7:03 AM

I guess there really isn't much advice to be given. Just start cutting and welding.

Added reply in a thread RMZ subframe on RM??? 5/31/2016 10:02 PM

You can finish anything with enough fornication...

Added reply in a thread 2006 RM250 Steer Stem Bearings. 5/31/2016 8:09 PM

Not really much available, if I order online it will turn out to be even more expensive after converting the US dollar and then shipping and handling and all that bullshit. If I could find aftermarket bearings in stock for a different bike that will ... more »