Removing plating From a platinum pipe

DTR830
Profile picture for user DTR830
Posts
961
Joined
8/14/2017
Location
Mountain Top, PA, USA
DTR830
Edited Date/Time 3/7/2019 2:36pm
Does anyone have experience with a shop that reverses the plating? Ive already called a few chrome shop with no luck..

Im trying to get my spare 96 platinum pipe back to a raw metal before I send it to pipe repair
|
mister2dt
Profile picture for user mister2dt
Posts
282
Joined
8/20/2018
Location
Canton, MS, USA
mister2dt 3/6/2019 9:57am
3/6/2019 9:57am
Put it in a tub of water and add some battery acid to it. The put the negative clip from a battery charger on the pipe and put the positive on a diode sitting in the water. The current will flake the plating off and leave the steel raw
1
ktm300hater
Profile picture for user ktm300hater
Posts
582
Joined
9/29/2009
Location
Stephenville, TX, USA
ktm300hater 3/6/2019 9:57am
3/6/2019 9:57am
A grinder
2
DTR830
Profile picture for user DTR830
Posts
961
Joined
8/14/2017
Location
Mountain Top, PA, USA
DTR830 3/6/2019 10:01am
3/6/2019 10:01am
mister2dt wrote:
Put it in a tub of water and add some battery acid to it. The put the negative clip from a battery charger on the pipe...
Put it in a tub of water and add some battery acid to it. The put the negative clip from a battery charger on the pipe and put the positive on a diode sitting in the water. The current will flake the plating off and leave the steel raw
Looking for a place to send it, not something I'm interested in attempting. Ty for the reply
1
mattyhamz2 3/6/2019 10:06am
3/6/2019 10:06am
Following. Looking to have this done to a few pipes.
3

The Shop

See All »
mister2dt
Profile picture for user mister2dt
Posts
282
Joined
8/20/2018
Location
Canton, MS, USA
mister2dt 3/6/2019 10:18am
3/6/2019 10:18am
mister2dt wrote:
Put it in a tub of water and add some battery acid to it. The put the negative clip from a battery charger on the pipe...
Put it in a tub of water and add some battery acid to it. The put the negative clip from a battery charger on the pipe and put the positive on a diode sitting in the water. The current will flake the plating off and leave the steel raw
DTR830 wrote:
Looking for a place to send it, not something I'm interested in attempting. Ty for the reply
Platers have so many regulations with EPA now, sending it off is not cost effective unless you find a place at the right time and they need a filler for a tank to drop. Anodizing and plating companies all have plating stripping baths. if you can find one near you who will take it, thats about your only option aside from having it bead blasted
1
mattyhamz2 3/6/2019 10:45am
3/6/2019 10:45am
Do you happen to know around what they charge?
DTR830
Profile picture for user DTR830
Posts
961
Joined
8/14/2017
Location
Mountain Top, PA, USA
DTR830 3/6/2019 10:50am
3/6/2019 10:50am
well pipe repair is up that way anyway. Thanks ill give them a call
1
DTR830
Profile picture for user DTR830
Posts
961
Joined
8/14/2017
Location
Mountain Top, PA, USA
DTR830 3/6/2019 10:58am
3/6/2019 10:58am
$58.30. Assuming if you had more it would be the same price
3
DTR830
Profile picture for user DTR830
Posts
961
Joined
8/14/2017
Location
Mountain Top, PA, USA
DTR830 3/6/2019 11:11am
3/6/2019 11:11am
DTR830 wrote:
$58.30. Assuming if you had more it would be the same price
Just called a hydro/plating shop & got a price for $200. #nothanks
mattyhamz2 3/6/2019 11:24am
3/6/2019 11:24am
DTR830 wrote:
$58.30. Assuming if you had more it would be the same price
Through who?
DTR830
Profile picture for user DTR830
Posts
961
Joined
8/14/2017
Location
Mountain Top, PA, USA
DTR830 3/6/2019 11:31am
3/6/2019 11:31am
The shop mentioned above
Zeke27G
Profile picture for user Zeke27G
Posts
1409
Joined
11/8/2011
Location
Ascot Park, CA, USA
Zeke27G 3/6/2019 11:59am
3/6/2019 11:59am Edited Date/Time 3/6/2019 12:00pm
Dear Op,

I took an old nickel plated KX500 FMF Gold Series pipe to Bush Polishing in Santa Ana to have the plating removed. They got all of the Nickel off, but there was still some Copper plating remaining in areas that are taking some elbow grease with a scotch brite pad and WD-40 to remove. The cost was $50 and it took a week. Once I get the final bit of copper removed from the pipe, I will post some before and after pictures. Also planning on sending it to Pipe Repair in Oregon to have some small dings removed. Once I'm done with it, it might be too nice to even use!

Anyhow, here is their info:

Bush Polishing
"A nice place to slide into" (Yes, that's their slogan!)
(714) 462-2034
2236 W 2nd St.
Santa Ana, CA 92703
9
RexEasely
Profile picture for user RexEasely
Posts
584
Joined
2/4/2019
Location
Pomona, CA, USA
RexEasely 3/6/2019 12:44pm
3/6/2019 12:44pm
Hahaha
Bush plating...nice place to slide into
1
eric513anderson 3/6/2019 12:47pm
3/6/2019 12:47pm
I haven’t tried this method but I’ve heard of people coating the whole pipe in easy off oven cleaner and letting it sit over night. Can is only a few bucks. Worth trying
1
zippytech
Profile picture for user zippytech
Posts
1511
Joined
9/8/2018
Location
Bethesda, OH, USA
zippytech 3/6/2019 12:48pm
3/6/2019 12:48pm
Will that remove the carbon build up in an old 2 stroke pipe
sandman768
Profile picture for user sandman768
Posts
8194
Joined
3/21/2014
Location
Saratoga Springs, NY, USA
sandman768 3/6/2019 2:02pm
3/6/2019 2:02pm
Commercial sandblasting shop....
1
jstevenson
Profile picture for user jstevenson
Posts
32
Joined
9/9/2017
Location
Orillia ont., CA
jstevenson 3/6/2019 3:51pm
3/6/2019 3:51pm
As sandman768 said. Then sand and wd40/scotch bright. Not worth the hassle of trying to chemically strip it. Here's one I've done.

3

Pit Row

See All »
delonick347
Profile picture for user delonick347
Posts
375
Joined
12/22/2011
Location
Omaha, NE, USA
delonick347 3/7/2019 11:34am
3/7/2019 11:34am
jstevenson wrote:
As sandman768 said. Then sand and wd40/scotch bright. Not worth the hassle of trying to chemically strip it. Here's one I've done. [img]https://p.vitalmx.com/photos/forums/2019/03/06/330059/s1200_20180914_073029.jpg[/img] [img]https://p.vitalmx.com/photos/forums/2019/03/06/330060/s1200_20180914_073022.jpg[/img]
As sandman768 said. Then sand and wd40/scotch bright. Not worth the hassle of trying to chemically strip it. Here's one I've done.

My dad bought a blasting cabinet at Harbor Freight and I'm interested in turning a "Gold Series" into a "Works Series" Wink and also cleaning up an actual PC Works Series pipe.

What media do you use?
sandman768
Profile picture for user sandman768
Posts
8194
Joined
3/21/2014
Location
Saratoga Springs, NY, USA
sandman768 3/7/2019 1:08pm
3/7/2019 1:08pm
You can successfully clean up the raw pipe with glass bead...nothing you do will touch the plated pipe, I tried unsuccessfully...a commercial blaster will have the correct media and high enough air pressure to remove it, then treat it like a raw pipe with the scotch brite sanding...When I get my pipes sanded to raw, I then blue the welds & refinish with clear heat spray paint...it holds up pretty good, but will need to be cleaned up periodically depending on usage.
Jonathan1717 3/7/2019 1:32pm
3/7/2019 1:32pm
Glass bead will remove plating but it needs to be shot at 250 psi plus. The problem is if you fire to much media it creates a lot of heat and can warp the metal. This isn’t a big deal on a pipe but the commercial company I used does hi end restorations of old cars and that much heat would destroy a fender or hood in a hurry. I tried every media I could find in my blast cabinet and it just knocked the shine off the nickel. Commercial company is the way to go. Spend the $40 and let someone else do it.
NvHermit
Profile picture for user NvHermit
Posts
889
Joined
7/21/2018
Location
Poeville, NV, USA
NvHermit 3/7/2019 1:53pm
3/7/2019 1:53pm
Stick it in your wife's self cleaning oven on the clean setting and open the windows.
aroark247
Profile picture for user aroark247
Posts
556
Joined
2/25/2014
Location
USA
aroark247 3/7/2019 2:35pm
3/7/2019 2:35pm
jstevenson wrote:
As sandman768 said. Then sand and wd40/scotch bright. Not worth the hassle of trying to chemically strip it. Here's one I've done. [img]https://p.vitalmx.com/photos/forums/2019/03/06/330059/s1200_20180914_073029.jpg[/img] [img]https://p.vitalmx.com/photos/forums/2019/03/06/330060/s1200_20180914_073022.jpg[/img]
As sandman768 said. Then sand and wd40/scotch bright. Not worth the hassle of trying to chemically strip it. Here's one I've done.

Literally putting some blood, sweat and tears into it, based off the floor pic

Post a reply to: Removing plating From a platinum pipe