Recent Activity
All
Motox627! Liked a reply to forum topic W.T.F. - I want some of what this guy is smoking...
1/21/2022 10:18pm
I've ridden plenty of things with 2 wheels, but legit would be worried to throw a leg over that thing!!
This forum topic has 37 replies.
Dirtydeeds Liked a reply to forum topic First Look KTM Factory Editions, all-new 450 SX-F and 250 SX-F
12/30/2021 11:49pm
Those are some expensive stickers
This forum topic has 154 replies.
-MAVERICK- Liked a reply to forum topic First Look KTM Factory Editions, all-new 450 SX-F and 250 SX-F
12/30/2021 11:47pm
Content cannot be rendered.
This forum topic has 154 replies.
dunerider209 Started a new thread Is this gap normal on lifter rod assembly?
1/8/2021 9:37am Is this gap suppose to be there or should it sit up against the nut? 
the actuator arm looks pretty close to level.
the actuator arm looks pretty close to level.
This forum thread has 3 replies.
dunerider209 Added a reply to Is this gap normal on lifter rod assembly?
1/8/2021 9:37am Cool, thanks man
dunerider209 Started a new thread Spark plugs reading please
1/6/2021 2:37pm Cr250 running 50/50 sunoco standard and pump 91 at 32:1. Bike has a bog down low. Currently running lectron carb and typical bolt on parts. Bike randomly started having this bog issue, replaced servo and piston ring to no avail. 
This forum thread has 2 replies.
dunerider209 Added a reply to Spark plugs reading please
1/6/2021 2:37pm Thanks for reply paw paw, the fuel mix is fresh and the ring has 5 hours on it. The last compression test was at 220 psi. I performed a leak test and found a massive air leak at the reed cage. The insulator is not sealing. I need to seal it up so I can then check the main seals...
dunerider209 Added a reply to 2007 Honda cr125, cr144 Engine Mod Questions
11/14/2020 8:47am Yea man, that thread was a bit ugly. I didn't even finish it. I ran the stock carb. Since it is a play bike I didn't go lectron or keihin, but he mentioned the stock carb is good if dialed in properly. Varner motorsports is his website. When he did mine I sent him the carb through the exhaust flange...
dunerider209 Added a reply to 2007 Honda cr125, cr144 Engine Mod Questions
11/13/2020 10:52pm Yea, not trying to start a pissing match about the guy, probably should have handled the situation better or hire some help if that thread is 100% accurate. Just bringing to light a cr builder with a pretty good engine package for a cr. It's been 3 years since he did mine and it took longer than I expected but...
dunerider209 Added a reply to 2007 Honda cr125, cr144 Engine Mod Questions
11/13/2020 10:13pm IMO ( and people will jump down my throat for this) Terry Varner is probably the best cr builder. That 125 at straight rhythm was a Varner build. I have a 02 cr125 play bike with a full Varner motor and can say it absolutely rips and holds it own on the track against the KTMs. I had plans for...
dunerider209 Added a reply to 2002 CR250 lost compression
10/31/2020 11:29pm Well if it lost all compression then the top end went. The last bike I saw that lost all compression smoked a hole in the piston from running lean. A couple things to check would be air leaks from crank seals, air boot area etc. Next, I would look at the jetting. Also too, you say a motor guy built...
PMR 3 Liked a reply to forum topic KTM 2019 250SXF won’t start with Vortex ignition!!
9/17/2020 8:32am
Man that's a trip, my 2019 Crf450 would start with a 2018 Vortex but not turn off.
This forum topic has 12 replies.
dunerider209 Added a reply to Worth it to upgrade to a 250f?
8/1/2020 10:20pm I went from a 125 straight to a 250 2t. Honestly the transition is not bad as long as you respect the bike and ride within your limits. I took the bike to the trails a few times to get use to the power difference and overall feel for the bike before going to the track. For your price range...
Mayo513 Liked a reply to forum topic Zach Osborne to race GNCC this weekend
7/11/2020 11:43pm
Are you racing it tomorrow? That will make the woods and tighter sections pretty interesting.
This forum topic has 194 replies.
dunerider209 Added a reply to What was your most memorable Dirt Bike Related trip to the ER?
7/7/2020 9:46am About 5 years ago I had my suspension set up on my 125 and the following weekend went out to club Moto. The suspension was super stiff and about 4 laps in I case an uphill double out of a corner and the bike bucks me and I Superman in with the throttle wide open. I went up the hill...
dunerider209 Added a reply to 2006 cr250r troubles
4/21/2020 8:17pm I'll have to check that out, it's been a while since I've repacked it . I was also thinking the servo motor isn't getting enough power to move the power valves and the only thing that I have not tested is the rectifier.
dunerider209 Added a reply to 2006 cr250r troubles
4/21/2020 8:14pm I compression tested it and the compression was fine. But I'm thinking about taking it apart and checking power cables and bore
dunerider209 Added a reply to 2006 cr250r troubles
4/21/2020 10:41am No, after Pismo trip where the bike ran great, I took it to the dirt a few weeks later and that's when it started running weird so I assumed it was the ring. I replaced the ring and still runs terrible.
dunerider209 Started a new thread 2006 cr250r troubles
4/20/2020 8:39pm Hey guys Im having issues with my cr not running correctly. Bike is ported with vforce reeds, pipe, silencer and lectron carb. Fresh top end, power valves serviced and a new servo motor. I run 50/50 mix Sunoco standard and 91 at 32:1. Bike is not as snappy off bottom, flat on top and worse at altitude even with lectron...
This forum thread has 6 replies.
dunerider209 Added a reply to lectron woth it or not?
4/9/2020 9:14am Although I don't have one on a 125, but I have one on my cr250. Personally I think their worth their money. Everyone says it takes away the hit but really it makes it a manageable and smoother hit IMHO. I personally ride at different elevations from tracks to trails in mountains, and have yet to have to adjust it...