Recent Activity
All
40acres Liked a reply to forum topic Is that rust on transmission gear(s)?
11/5/2024 6:31am
Are you the same guy who posted this same question about a month ago? Run it, it's fine.
This forum topic has 2 replies.
1mph Added a reply to Is that rust on transmission gear(s)?
11/5/2024 8:18am yes, apologize for the sort of repost. the first time i wasnt sure what that part was, posted on reddit and one guy said looks like a crank rod, huh, lol. as far as my scope can see, all gears are like new, weird thats the only gear that looks like that, including the teeth, the teeth shows the same...
1mph Started a new thread Is that rust on transmission gear(s)?
11/4/2024 5:05pm At first, with an endoscope, I couldn't tell which part it was, then realized it's part of a gear when i looked in the manual, the possible corrosion is within the red circled area of the diagram. Both bikes are 2021 YZ125, purchased around late 2023. 2nd image is my son's bike, got it from owner who bought it new...
This forum thread has 2 replies.
1mph Added a reply to 2023 YZ125 - Jetting Fix
10/26/2024 7:42pm 2023 YZ125 - Jetting Fix Can't figure out how to save this thread to my account, so am just replying to save it.
1mph Added a reply to 2018-2024 RM-Z450 Service Manual
1/15/2024 9:31am here you go for $19.99, don't know the publisher and if it's good or not. ebay 2015-2024 digital manual on CD. that's all i found quickly.
1mph Added a reply to 2018-2024 RM-Z450 Service Manual
1/14/2024 12:30pm can't find a free 2018+ one. but chain slack, should be right around 2", chain slide at the front of swingarm, at the end of that chain slide to bottom of chain at the top side, should have a tiny droop to it. too loose, chain may come off, too tight, will put extra stress on engine. something like this...
1mph Added a reply to Mikuni TMX38 what is this part?
1/14/2024 10:02am looking from the outside, i see where the choke circuit leads to. again, ty
DynoDan22 Liked a reply to forum topic Mikuni TMX38 what is this part?
1/13/2024 8:42pm
That tube is the choke circuit feed. It cannot be removed and is not serviceable.
This forum topic has 4 replies.
1mph Added a reply to Mikuni TMX38 what is this part?
1/13/2024 8:42pm ty
1mph Started a new thread Mikuni TMX38 what is this part?
1/13/2024 6:48pm does not explain what this is in the manual This part cannot be removed? What's it called? What's it for?
This forum thread has 4 replies.
MxAddic Liked a reply to forum topic Is this about a normal amount of carbon on piston for 10 hours?
1/13/2024 5:38pm
Pro Circuit, they have a great setting.
This forum topic has 20 replies.
1mph Added a reply to Is this about a normal amount of carbon on piston for 10 hours?
1/13/2024 5:30pm oh cool page, ty.
1mph Added a reply to Is this about a normal amount of carbon on piston for 10 hours?
1/13/2024 4:30pm well, need to set float height properly first, otherwise cannot do jetting properly. sorry, but what is PC?
MxAddic Liked a reply to forum topic Is this about a normal amount of carbon on piston for 10 hours?
1/13/2024 4:28pm
I would start with the PC specs and adjust for local and fuel.
This forum topic has 20 replies.
1mph Added a reply to Is this about a normal amount of carbon on piston for 10 hours?
1/13/2024 4:58pm lugging, i think INeedaNewUsername meant just going too slow most of the time to burn off enough of the oil . what you said, if so, on my brand new one, i was cleaning out the carb from sitting with original dealer gas for so long and changing out the jet block gasket to JD's, found that the float height...
MxAddic Liked a reply to forum topic Is this about a normal amount of carbon on piston for 10 hours?
1/13/2024 3:53pm
I don't think it was lugged. The way the piston looks it never ran right. The carbon will not be an issue going forward.
This forum topic has 20 replies.
Bruce372 Liked a reply to forum topic Is this about a normal amount of carbon on piston for 10 hours?
1/13/2024 3:27pm
I wouldn't use the decarbonizer. Just jet it right and run it. If you are really bothered, just buy a bade gasket wnr rings and manually clean the top end. Don't worry, just go ride
This forum topic has 20 replies.
1mph Added a reply to Is this about a normal amount of carbon on piston for 10 hours?
1/13/2024 3:26pm "lugging" i just thought about that, it had a shorty silencer, probably mostly ridden on tracks if not completely, the front number plate, upper forks and protectors all have tons of tiny dings everywhere, probably from lugging behind everyone else, getting roost constantly. lol.
1mph Added a reply to Is this about a normal amount of carbon on piston for 10 hours?
1/13/2024 3:05pm i got the same bike, seller bought it brand new, sat in garage for 2 years unridden, once i do break in, i'll change jetting.
MxAddic Liked a reply to forum topic Is this about a normal amount of carbon on piston for 10 hours?
1/13/2024 3:00pm
These bikes respond amazing to jetting.
This forum topic has 20 replies.