2027 CRF450R

mxracer515
Posts
92
Joined
8/13/2015
Location
Drexel, MO, USA
11/16/2026 3:02pm

CRMX105  7hrs when it happened. & only has not started correctly 1 time     My friends was less that 1 hour.

gscx , mine will ping a bit down low in a tight corner. I'm glad you mentioned the in gear rpm changing .I had forgot to mention it.

 I raise idle but compromised & set idle bit lower than I would like in neutral. so its not so high in gear otherwise. I haven't had stalls on track even with lower idle.

crmx105
Posts
709
Joined
5/7/2016
Location
Dunnellon, FL, USA
11/16/2026 3:33pm
mxracer515 wrote:
CRMX105  7hrs when it happened. & only has not started correctly 1 time     My friends was less that 1 hour.gscx , mine will ping...

CRMX105  7hrs when it happened. & only has not started correctly 1 time     My friends was less that 1 hour.

gscx , mine will ping a bit down low in a tight corner. I'm glad you mentioned the in gear rpm changing .I had forgot to mention it.

 I raise idle but compromised & set idle bit lower than I would like in neutral. so its not so high in gear otherwise. I haven't had stalls on track even with lower idle.

5.2 hr on mine. Haven't had the decomp issue so far. Stalling issue has improved now that bike has more time on it. Think mapping could be cleaner. Seems like map 2 runs the cleanest.

FGR01
Posts
6179
Joined
10/1/2006
Location
USA
11/16/2026 6:52pm
Anyone using a torque wrench for that second drain bolt? I imagine 8-10nm is about right. I have a CDI Torque that is 4-26nm for stuff...

Anyone using a torque wrench for that second drain bolt? I imagine 8-10nm is about right. I have a CDI Torque that is 4-26nm for stuff like this. I also need to find the washers, no one stocks those by me, 2 weeks out on motorsport.com;  all the rest of the parts for an oil change are the same, so far as I can tell. 

Are you talking about the big 14mm sealing washer on the bottom or the smaller 6mm one on the left side cover?

Broseph
Posts
1237
Joined
4/28/2018
Location
Sand City 100, ID, USA
11/16/2026 7:37pm
gscx wrote:
I put some good time on the bike Sunday.The idle is an issue. The bike very clearly increases the RPM when you put it into gear...

I put some good time on the bike Sunday.

The idle is an issue. The bike very clearly increases the RPM when you put it into gear and I think this is part of the reduced engine breaking everyone is talking about. Problem is the difference is so much that in order for it to not stall out (which it still does a lot) the idle in gear is crazy high. I think the decomp may be part of this as well like it engages at too low of an rpm. Does anyone else get loud chirping when the bike is down low in RPMs?

It is fast and gearing is high. I've gotten used to it but might need one more tooth on the rear for some people. 

Handling seems fine, Track wasn't too rough but was fast and didnt get any headshake. Suspension seems ok too. Dont be afraid to go out on rebound. It seems heavy. 

Its a good bike, a little more honda than I had hoped, but the quality is great.

Funny you mention the idle increase. My ‘27 Yamaha also increases idle speed when in gear and also has almost no engine braking. This was the first time I noticed a bike doing that. Pretty cool honestly. I’m not a fan of engine braking. 

2

The Shop

yamathumb
Posts
236
Joined
3/11/2025
Location
Redding, CA, USA
1 day ago

Good thing someone figured out to bump the bike past the compression stroke and retry starting. Lol......

1
3
sandtrack315
Posts
2879
Joined
7/19/2013
Location
Philadelphia, PA, USA
1 day ago
Anyone using a torque wrench for that second drain bolt? I imagine 8-10nm is about right. I have a CDI Torque that is 4-26nm for stuff...

Anyone using a torque wrench for that second drain bolt? I imagine 8-10nm is about right. I have a CDI Torque that is 4-26nm for stuff like this. I also need to find the washers, no one stocks those by me, 2 weeks out on motorsport.com;  all the rest of the parts for an oil change are the same, so far as I can tell. 

FGR01 wrote:

Are you talking about the big 14mm sealing washer on the bottom or the smaller 6mm one on the left side cover?

Smaller 6mm!

FGR01
Posts
6179
Joined
10/1/2006
Location
USA
1 day ago
Anyone using a torque wrench for that second drain bolt? I imagine 8-10nm is about right. I have a CDI Torque that is 4-26nm for stuff...

Anyone using a torque wrench for that second drain bolt? I imagine 8-10nm is about right. I have a CDI Torque that is 4-26nm for stuff like this. I also need to find the washers, no one stocks those by me, 2 weeks out on motorsport.com;  all the rest of the parts for an oil change are the same, so far as I can tell. 

FGR01 wrote:

Are you talking about the big 14mm sealing washer on the bottom or the smaller 6mm one on the left side cover?

Smaller 6mm!

Partzilla says they have it in stock:  https://www.partzilla.com/product/honda/90404-HW1-670

I've used these bulk ones from Amazon for years with success.  Not sure the outer diameter of the Honda OEM one, 10mm or 12mm.  Looks 12mm in pictures.  Measure your current one.   https://www.amazon.com/uxcell-Copper-Washer-Sealing-Fastener/dp/B01LXD5PYF/ref=sr_1_21?th=1

Looks like they also have the correct size 14mm one   14x20x1mm

1
Honda820
Posts
39
Joined
10/6/2020
Location
Wilkesboro, NC, USA
1 day ago
yamathumb wrote:

Good thing someone figured out to bump the bike past the compression stroke and retry starting. Lol......

No, let’s go ahead and hook jumper cables to a battery that’s not meant for jumper cables 🤦🏻‍♂️🤦🏻‍♂️. People panicked for no reason. Good call on your part 

Honda820
Posts
39
Joined
10/6/2020
Location
Wilkesboro, NC, USA
1 day ago Edited Date/Time 1 day ago
gscx wrote:
I put some good time on the bike Sunday.The idle is an issue. The bike very clearly increases the RPM when you put it into gear...

I put some good time on the bike Sunday.

The idle is an issue. The bike very clearly increases the RPM when you put it into gear and I think this is part of the reduced engine breaking everyone is talking about. Problem is the difference is so much that in order for it to not stall out (which it still does a lot) the idle in gear is crazy high. I think the decomp may be part of this as well like it engages at too low of an rpm. Does anyone else get loud chirping when the bike is down low in RPMs?

It is fast and gearing is high. I've gotten used to it but might need one more tooth on the rear for some people. 

Handling seems fine, Track wasn't too rough but was fast and didnt get any headshake. Suspension seems ok too. Dont be afraid to go out on rebound. It seems heavy. 

Its a good bike, a little more honda than I had hoped, but the quality is great.

The idle settings do need some tweaking and I believe it’s the culprit for the decompression issue. It believe the idle is way to low when it’s cold, therefore the decompression system is engaging when it shouldn’t. That causes the bike to stop between TDC and there’s to much compression for the starter to turn the bike over. If you rotate the engine around and get the bike off TDC, then everything works like it’s supposed to. I’ve been running my idle high from day one with no stalling or starting issues. I have 8 hours on the bike now. Honda needs to adjust the ECU so that the bike idles better. Anyway, enjoy the bike! 👍

2
sandtrack315
Posts
2879
Joined
7/19/2013
Location
Philadelphia, PA, USA
1 day ago
FGR01 wrote:

Are you talking about the big 14mm sealing washer on the bottom or the smaller 6mm one on the left side cover?

Smaller 6mm!

FGR01 wrote:
Partzilla says they have it in stock:  https://www.partzilla.com/product/honda/90404-HW1-670I've used these bulk ones from Amazon for years with success.  Not sure the outer diameter of...

Partzilla says they have it in stock:  https://www.partzilla.com/product/honda/90404-HW1-670

I've used these bulk ones from Amazon for years with success.  Not sure the outer diameter of the Honda OEM one, 10mm or 12mm.  Looks 12mm in pictures.  Measure your current one.   https://www.amazon.com/uxcell-Copper-Washer-Sealing-Fastener/dp/B01LXD5PYF/ref=sr_1_21?th=1

Looks like they also have the correct size 14mm one   14x20x1mm

Thanks, you torquing to a spec, or just doing it kinda like the oil filter cover bolts, hand tighten till "good"?

FGR01
Posts
6179
Joined
10/1/2006
Location
USA
1 day ago

Thanks, you torquing to a spec, or just doing it kinda like the oil filter cover bolts, hand tighten till "good"?

I don't currently have a CRF450, so can't speak specifically on that.  But I've been wrenching on bikes so long I don't worry about a torque wrench for routine stuff like this.  You can feel when the copper washer has some squish to it and not go crazy and blow the threads out.

1
Honda820
Posts
39
Joined
10/6/2020
Location
Wilkesboro, NC, USA
1 day ago

Thanks, you torquing to a spec, or just doing it kinda like the oil filter cover bolts, hand tighten till "good"?

FGR01 wrote:
I don't currently have a CRF450, so can't speak specifically on that.  But I've been wrenching on bikes so long I don't worry about a torque...

I don't currently have a CRF450, so can't speak specifically on that.  But I've been wrenching on bikes so long I don't worry about a torque wrench for routine stuff like this.  You can feel when the copper washer has some squish to it and not go crazy and blow the threads out.

 There willbe a lot of people strip that bolt out on the ignition cover side. The little small 6 mm bolt. Not sure why they did that, I’ve owned every model CRF 450 and they’ve never done that before.

HondaTech25
Posts
229
Joined
3/12/2026
Location
Maysville, KY, USA
1 day ago
gscx wrote:
I put some good time on the bike Sunday.The idle is an issue. The bike very clearly increases the RPM when you put it into gear...

I put some good time on the bike Sunday.

The idle is an issue. The bike very clearly increases the RPM when you put it into gear and I think this is part of the reduced engine breaking everyone is talking about. Problem is the difference is so much that in order for it to not stall out (which it still does a lot) the idle in gear is crazy high. I think the decomp may be part of this as well like it engages at too low of an rpm. Does anyone else get loud chirping when the bike is down low in RPMs?

It is fast and gearing is high. I've gotten used to it but might need one more tooth on the rear for some people. 

Handling seems fine, Track wasn't too rough but was fast and didnt get any headshake. Suspension seems ok too. Dont be afraid to go out on rebound. It seems heavy. 

Its a good bike, a little more honda than I had hoped, but the quality is great.

Honda820 wrote:
The idle settings do need some tweaking and I believe it’s the culprit for the decompression issue. It believe the idle is way to low when...

The idle settings do need some tweaking and I believe it’s the culprit for the decompression issue. It believe the idle is way to low when it’s cold, therefore the decompression system is engaging when it shouldn’t. That causes the bike to stop between TDC and there’s to much compression for the starter to turn the bike over. If you rotate the engine around and get the bike off TDC, then everything works like it’s supposed to. I’ve been running my idle high from day one with no stalling or starting issues. I have 8 hours on the bike now. Honda needs to adjust the ECU so that the bike idles better. Anyway, enjoy the bike! 👍

Adjust the idle higher then, we use to turn up the early 450L models because they flamed out easy at the stock idle speed. 

Just turn the high idle knob forward. 

1
HondaTech25
Posts
229
Joined
3/12/2026
Location
Maysville, KY, USA
1 day ago

Thanks, you torquing to a spec, or just doing it kinda like the oil filter cover bolts, hand tighten till "good"?

FGR01 wrote:
I don't currently have a CRF450, so can't speak specifically on that.  But I've been wrenching on bikes so long I don't worry about a torque...

I don't currently have a CRF450, so can't speak specifically on that.  But I've been wrenching on bikes so long I don't worry about a torque wrench for routine stuff like this.  You can feel when the copper washer has some squish to it and not go crazy and blow the threads out.

Honda820 wrote:
 There willbe a lot of people strip that bolt out on the ignition cover side. The little small 6 mm bolt. Not sure why they did...

 There willbe a lot of people strip that bolt out on the ignition cover side. The little small 6 mm bolt. Not sure why they did that, I’ve owned every model CRF 450 and they’ve never done that before.

The original 450x had a drain bolt in the ignition cover. People just need to not be idiots 

1
gscx
Posts
203
Joined
4/27/2018
Location
Schenectady, NY, USA
1 day ago
gscx wrote:
I put some good time on the bike Sunday.The idle is an issue. The bike very clearly increases the RPM when you put it into gear...

I put some good time on the bike Sunday.

The idle is an issue. The bike very clearly increases the RPM when you put it into gear and I think this is part of the reduced engine breaking everyone is talking about. Problem is the difference is so much that in order for it to not stall out (which it still does a lot) the idle in gear is crazy high. I think the decomp may be part of this as well like it engages at too low of an rpm. Does anyone else get loud chirping when the bike is down low in RPMs?

It is fast and gearing is high. I've gotten used to it but might need one more tooth on the rear for some people. 

Handling seems fine, Track wasn't too rough but was fast and didnt get any headshake. Suspension seems ok too. Dont be afraid to go out on rebound. It seems heavy. 

Its a good bike, a little more honda than I had hoped, but the quality is great.

Honda820 wrote:
The idle settings do need some tweaking and I believe it’s the culprit for the decompression issue. It believe the idle is way to low when...

The idle settings do need some tweaking and I believe it’s the culprit for the decompression issue. It believe the idle is way to low when it’s cold, therefore the decompression system is engaging when it shouldn’t. That causes the bike to stop between TDC and there’s to much compression for the starter to turn the bike over. If you rotate the engine around and get the bike off TDC, then everything works like it’s supposed to. I’ve been running my idle high from day one with no stalling or starting issues. I have 8 hours on the bike now. Honda needs to adjust the ECU so that the bike idles better. Anyway, enjoy the bike! 👍

Adjust the idle higher then, we use to turn up the early 450L models because they flamed out easy at the stock idle speed. Just turn the...

Adjust the idle higher then, we use to turn up the early 450L models because they flamed out easy at the stock idle speed. 

Just turn the high idle knob forward. 

Yea bro I def didn't think of this. When the idle is so high in gear it moves you forward when off the gas into turns its a problem. And engine braking is something I use to help in turns. But yea, just turn it up. 

 

sandtrack315
Posts
2879
Joined
7/19/2013
Location
Philadelphia, PA, USA
14 hours ago
Honda820 wrote:
 There willbe a lot of people strip that bolt out on the ignition cover side. The little small 6 mm bolt. Not sure why they did...

 There willbe a lot of people strip that bolt out on the ignition cover side. The little small 6 mm bolt. Not sure why they did that, I’ve owned every model CRF 450 and they’ve never done that before.

I do think it’s odd they don’t give you a torque spec. I know most people don’t have good wrenches for low specs, but give us something to go off of. I feel the same way for the oil filter cover bolts. 

Rawly
Posts
1198
Joined
9/12/2019
Location
Simi Valley, CA, USA
5 hours ago
Honda820 wrote:
 There willbe a lot of people strip that bolt out on the ignition cover side. The little small 6 mm bolt. Not sure why they did...

 There willbe a lot of people strip that bolt out on the ignition cover side. The little small 6 mm bolt. Not sure why they did that, I’ve owned every model CRF 450 and they’ve never done that before.

I do think it’s odd they don’t give you a torque spec. I know most people don’t have good wrenches for low specs, but give us...

I do think it’s odd they don’t give you a torque spec. I know most people don’t have good wrenches for low specs, but give us something to go off of. I feel the same way for the oil filter cover bolts. 

If I’m not calibrating my torque wrenches, the only one I’d feel safe with for the small diameter screws would be the screwdriver style torque wrenches. Pretty hard to over torque with them if the accuracy is off.  

1
sandtrack315
Posts
2879
Joined
7/19/2013
Location
Philadelphia, PA, USA
4 hours ago
Rawly wrote:
If I’m not calibrating my torque wrenches, the only one I’d feel safe with for the small diameter screws would be the screwdriver style torque wrenches...

If I’m not calibrating my torque wrenches, the only one I’d feel safe with for the small diameter screws would be the screwdriver style torque wrenches. Pretty hard to over torque with them if the accuracy is off.  

those wrenches are sweet. 

Meister
Posts
3338
Joined
3/21/2013
Location
Canton, OH, USA
3 hours ago

Does it still have that big stupid allen drain plug on the bottom? I hated that thing on my 21we. I was super interested in the 27 but the reports spooked me a little. Had a line on onr for 10k otd but drug my feet. 

crmx105
Posts
709
Joined
5/7/2016
Location
Dunnellon, FL, USA
1 hour ago
Meister wrote:
Does it still have that big stupid allen drain plug on the bottom? I hated that thing on my 21we. I was super interested in the...

Does it still have that big stupid allen drain plug on the bottom? I hated that thing on my 21we. I was super interested in the 27 but the reports spooked me a little. Had a line on onr for 10k otd but drug my feet. 

No longer has the big drain bolt. Has a smaller allen head and an 8 mil bolt on the ignition cover.

kiwifan
Posts
9870
Joined
10/31/2009
Location
USA
6 minutes ago
Meister wrote:
Does it still have that big stupid allen drain plug on the bottom? I hated that thing on my 21we. I was super interested in the...

Does it still have that big stupid allen drain plug on the bottom? I hated that thing on my 21we. I was super interested in the 27 but the reports spooked me a little. Had a line on onr for 10k otd but drug my feet. 

The only thing that is a potential spooker (is that a word ? lol) is the starting issue which there is a way around it as noted a few times in this thread, otherwise seems an amazing bike 

What else spooks you ??? 

Post a reply to: 2027 CRF450R

The Latest