Recent Activity
All
TropicPilot Liked a reply to forum topic Whoregay Prado
8/16/2026 6:39pm
Just watched his press conference. He obviously mispronounced Jorge's name on purpose. Just one more data point to prove that Doucheboy is a douche.
This forum topic has 319 replies.
mxrose3 Liked a reply to forum topic Whoregay Prado
8/16/2026 6:39pm
While I legitimately want to see an American rider win, I hate that little midget fucker.
This forum topic has 319 replies.
ShirtOff Liked a reply to forum topic Whoregay Prado
8/16/2026 6:39pm
I don't agree with this. I believe Jorge does care. You see how fired up he gets against some of his competitors (Webb, Hunter). Prado has been known to show people a wheel or 2 so I don't think this is smart of Haiden to do
This forum topic has 319 replies.
DonJulio Liked a reply to forum topic Whoregay Prado
8/16/2026 6:39pm
Gayden just doesn’t learn does he? Salty lil bitch
This forum topic has 319 replies.
gt80rider Liked a forum topic Whoregay Prado
8/16/2026 6:38pm
Cringe lord gets smoked both motos by Jorge, then calls him Whoregay in the press conference??? Lolll.... cant wait to see what Jorge does about that in upcoming races.... #whatgoesaroundcomesaround
This forum topic has 319 replies.
TropicPilot Liked a reply to forum topic Yamaha Motor Closing Cypress Operations
8/14/2026 10:27pm
Which political party has had a statewide monopoly in California for the last 40 years? I can't quite remember.
This forum topic has 34 replies.
SWMX Added a reply to Showa 49 Help
8/14/2026 6:12pm Cupped side of the seal, toward the fork cap.
RightHookNoCandy Liked a reply to forum topic TBT Racing drama
8/14/2026 6:10pm
This seems like a straight up pyramid scheme? Surely this guy won't be able to operate this way for much longer before people reaslize and stop signing up? Also would have to think the customer base would soon catch on. There is a TBT racing near me and the prices are outrageous, it would cost more for me to have my stuff revalved by a guy who started doing suspension out of his barn under the TBT name 2 years ago than send it to factory connection who operates with a factory race team and has nationwide factory support.
This forum topic has 71 replies.
SWMX Added a reply to WTB 18-26 RMZ 450 parts
8/13/2026 10:22pm PM me, got a set of Ti Raptor pegs
SWMX Added a reply to First Year WP Cone Valve?
8/12/2026 11:52pm Nagl maybe even 09.
SWMX Added a reply to First Year WP Cone Valve?
8/12/2026 11:51pm Torn between 07 and 2010. The caps look similar to what was on Rattrays bike in gps, and Alessis bike stateside in 2007. However I dont believe that indicates anything for the midvalve as they could mate any configuration to the CA. So I could very well be wrong. Nagl and Cairoli in 2010 confirmed cone valve. That base valve...
SWMX Added a reply to Pros/Former Pros out in the wild
6/22/2026 9:56pm Cairoli cut me off in traffic while over here for MX series. Giant shades only recognized him by the teeth in the rear view.
30minmotos Liked a forum topic Chainsaws and airhorns = low iq inbred
6/20/2026 10:44pm
Change my mind
This forum topic has 181 replies.
SWMX Added a reply to Tight spot - front wheel
6/6/2026 9:54pm +1 Bent disk. Had this issue on my KX. Replaced rotor and good as new.
SWMX Added a reply to Kyb rebound needle stuck closed
6/5/2026 4:34pm The needle guide is where your needle tip seals to. The clip pen will be the final bit pressed into the shaft, which retains the guide. The tricky parts is the depth of the clip pen and guide(needle seat) is crucial as it plays a role with your total clicker range. Too deep youll end up with less clickers possibly...
SWMX Added a reply to Kyb shock clevis removal/Install
6/2/2026 11:25am Hate that. Count how many total clicks you have. Measure from the end of the 12mm shank, down to the top of the jam nut, note this distance. When re assembling, match this distance once tight. Count your clickers again. It’s normal to be within 1-2 clicks! Be sure you use high strength high heat retaining compound when going back...
FNG Liked a reply to forum topic Stapes Performance
6/1/2026 4:36pm
Have seen the work, hit and miss. Seen the failures at SX last year, heard of ridiculous invoices as well as wait times. By local knowledge he was an enzo employee that ended up doing his own thing shortly after, credit to him for that. The MX6 guy is coming in with good money supporting them… but money can’t buy reputation. Or can it? Never been soured myself but I knew to take money elsewhere. There are plenty out there industry/tuning company wise and average joe that are soured on him.
This forum topic has 32 replies.
disbanded Liked a reply to forum topic Stapes Performance
6/1/2026 4:35pm
This has the possibility of being a great thread
This forum topic has 32 replies.
SWMX Added a reply to Stapes Performance
5/31/2026 11:18pm 👀 oh boy
SWMX Added a reply to 26 Factory Edition Xact Pro shock questions - HELP!!
4/26/2026 5:05pm The correct length spring for the shock design, is 240mm +/- 5mm. Very tough to fit longer with the Xtrig collar. I have fit 247mm as well as 250mm springs to PRODUCTION shock with standard collar however the design length is always best bet. Time for new spring!