sdhuskyrider

Member Summary

Followers: 1

Following: 1

Forum topics started: 59

Forum replies: 298

Lives in:

San Diego, CA, USA

Member Since:

10/27/2017

Recent Activity

Filter:

All

sdhuskyrider Added a reply to WTB: OEM YZ250 Triple Clamps

12/29/2021 6:19pm

I have a set off of a 2020 YZ125. Should be exactly the same.

sdhuskyrider Added a reply to HRC spec powervalve spacer

1/22/2021 9:40pm

That generation of engine used both a variable exhaust port and sub chamber to alter power. The cover is part of the sub chamber.

matt.3150 Liked a reply to forum topic 94-97 CR 125 HRC Spec Cone Pipe

1/22/2021 9:34pm

Can you put up a picture of Steve Lamson works Honda CR125 with that pipe on it? Between 1994-1997. Not saying your wrong , I just don’t recall ever seeing any of the factory Honda 125!between 1994-1997 having a cone pipe on it. I could be wrong those. Here a picture of his silencer though.

This forum topic has 14 replies.

sdhuskyrider Started a new thread WTT: 2002 CR250 PC Works Pipe and R304 Silencer for a 2003 Exhaust System

12/20/2020 3:26pm

Looking to trade my 02 PC system for an 03 system of equal value.

This forum thread has 0 replies.

sdhuskyrider Added a reply to 2020 YZ125 Jetting Spec Needed for Glamis

11/28/2020 6:32pm

Thats good to hear. The 500 probably worked well for me because it was about 75F, zero elevation and very dry.

Mr. Robinson Liked a reply to forum topic 2020 YZ125 Jetting Spec Needed for Glamis

11/28/2020 2:59pm

I'm not surprised. I think the hot set up on the sandy tracks over in Europe for the YZ cup 125's is to run about a 520 with 44-74 needle.

This forum topic has 11 replies.

sdhuskyrider Added a reply to 2020 YZ125 Jetting Spec Needed for Glamis

11/26/2020 4:49pm

I had to go all way up to 500!!! I'm running a Bill's pipe and silencer and Vforce 3 reed cage for reference. Stock needle, clip on position 4, stock pilot.

sdhuskyrider Added a reply to 2020 YZ125 Jetting Spec Needed for Glamis

11/24/2020 2:19am

I have a 460, 470, 480 and 490. I might be able to get my hands on a 500. I normally run a 430 main and its pretty tits. My plan is to start with the 460. I bumped the pilot from 37.5 back to 40 and the needle from 44-74-3 to 43-74-4 so half clip richer from current setting...

AJ565 Liked a reply to forum topic 125/150/250/300 KTM/HUS/GG jetting thread

11/24/2020 2:13am

Very little clutch if any. I have the stock power valve spring set to 1 3/4 turns in from all the way out. My throttle response is instant. I've let a few slower than me guys ride it and they don't like it because its to snappy for them like an off to on switch. Check out this video, while not in sand, there is slow sections and parts that transition from off idle to wide open and you can hear how the engine reacts. https://www.youtube.com/watch?v=3w17-wLnLBI&t=3s

This forum topic has 1228 replies.

sdhuskyrider Started a new thread 2020 YZ125 Jetting Spec Needed for Glamis

11/23/2020 9:22am

Does anyone have a proven YZ125 jetting spec for Glamis? Heading out there tomorrow for the day. I will be running a 6 paddle tire.

This forum thread has 11 replies.

sdhuskyrider Started a new thread 17' TC250 Jetting Help

11/23/2020 9:19am

Has anyone nailed jetting specs for the 17' Huskatoom TC250? I have been hitting Pala in Socal which is about 500' above sea level and temps are pretty steady at 70*F right now. Bike is blubbery down low but crisp mid and up. I checked my float level which is 6-7mm per Mikuni spec and I dropped the pilot from...

This forum thread has 334 replies.

sdhuskyrider Added a reply to 17' TC250 Jetting Help

11/23/2020 9:19am

My TC250 runs perfect 👌 Not sure what you guys have and haven't tried but the specs posted in this thread are money.

sdhuskyrider Started a new thread Low Hours Bill's Pipe and Silencer and Vforce 3 from 2020 YZ125

7/12/2020 11:10am

Gotta raise a few bucks since I'm going Covid poor. Retail on pipe and silencer is $370. Selling for $250 and shipping. Has about 5 hours of light use. No dents. $100 shipped on the Vforce 3. Has 2 hours of run time on it.

This forum thread has 3 replies.

sdhuskyrider Added a reply to Low Hours Bill's Pipe and Silencer and Vforce 3 from 2020 YZ125

7/12/2020 11:10am

Pipe and silencer sold.

sdhuskyrider Started a new thread 2001 YZ125 Part Out - Good Shape

5/18/2020 7:19pm

Parting out a complete 2001 YZ125. Pretty much complete bike. Pro Circuit pipe and silencer, Applied top clamp with Tag fat bars and some other goodies. Tranmission is good. Clutch is in great shape. Cylinder needs to be replated but won't require welding. Crank seems Ok. Tank is solid. White airbox is fairly clean. Lots of clean parts! Lmk what...

This forum thread has 29 replies.