Recent Activity
All
jwolfman317 Added a reply to 2022 Gas Gas MC250 100/90-19 rear tire?
2/5/2022 9:38am I did check the owner’s manual before posting, and I was quite surprised that it said 100/90. We will move that over to the 125 and throw on a 110.
More »
jwolfman317 Added a reply to 2022 Gas Gas MC250 100/90-19 rear tire?
2/5/2022 9:37am Are these Gas Gas bikes?
jwolfman317 Added a reply to 2022 Gas Gas MC250 100/90-19 rear tire?
1/31/2022 9:44am Thanks for the responses. Just to clarify, this is a 2-stroke.
jwolfman317 Started a new thread 2022 Gas Gas MC250 100/90-19 rear tire?
1/28/2022 8:03am We just picked up a new bike for my son. I was expecting it to have a 110/90-19 on it, but instead it was a 100 just like a 125. What’s everyone’s thoughts about it?
This forum thread has 12 replies.
jwolfman317 Started a new thread VP MRX02 vs Renegade SX2
5/3/2021 11:32am Hello guys. What’s everyone’s thought on the performance of these two? SX 2 is 30 percent less in price.
This forum thread has 1 reply.
jwolfman317 Added a reply to Vertex vs OEM gaskets/seals
3/5/2021 9:50am What bike is this for?
jwolfman317 Started a new thread Ktm aftermarket rotors
1/25/2021 9:15am Hello, guys. What’s everyone’s thoughts on the best rotor for a Ktm 125? I know oem is good but the DP pads that we were running did some damage, and it is bent slightly, so looking to replace with another 260mm disc. On a side note, has anyone had issues with EBC Mxs pads being too thick and dragging?
This forum thread has 17 replies.
jwolfman317 Added a reply to Ktm aftermarket rotors
1/22/2021 5:09am Thanks for the replies. Are you guys that are running Galfer rotors using their Sintered HH pads?
jwolfman317 Added a reply to Ktm aftermarket rotors
1/21/2021 6:28pm What series of braking rotors and pads ?
jwolfman317 Added a reply to KTM SX125 does not want to rev out proper unloaded
5/21/2020 4:00pm I would take a look at your spark plug boot. It eventually wears and loses contact with the spark plug. We have an ‘18 and had this issue that caused a misfire from mid to top. The only issue with the power valve has been just after a new top end when the o-rings that are on the shaft have...
jwolfman317 Started a new thread Renegade race gas
10/31/2019 11:14am Does anyone know where to buy within a reasonable distance of Wichita, KS?
This forum thread has 2 replies.
jwolfman317 Added a reply to 2018 KTM 125 replacement brake pads
10/1/2019 2:05pm Are these the “sintered double H” ? How do they feel and wear compared to oem?
jwolfman317 Started a new thread 2018 KTM 125 replacement brake pads
9/30/2019 5:05pm Are there any good aftermarket options? The oem brake pads are pretty high. I’ve seen where the aftermarket pads might not have the additional insulators on the rear pads like oem.
This forum thread has 10 replies.
jwolfman317 Started a new thread 2007 YZ250 carb on a 2018 KTM 125?
9/16/2019 11:52am I’m curious if this will work, with installing the correct jetting and blocking off the power jet? I’m thinking that it is basically the same carb as the 2016 KTM 125, except for the power jet and throttle position sensor.
This forum thread has 9 replies.
jwolfman317 Added a reply to 2007 YZ250 carb on a 2018 KTM 125?
9/15/2019 10:53am Thanks for the info, guys. Would I need to do anything with the power jet? I know that I need the intake boot and fuel hose from the 2016, but will it work with the 2018 throttle assembly and cable? What jetting? I’d like to do the stic at some point but will have to wait for a bit.
jwolfman317 Added a reply to Mikuni tmx 38mm throttle slide plating issue
9/12/2019 4:40pm I have heard a lot of good things about this. How much does it cost?
jwolfman317 Added a reply to Mikuni tmx 38mm throttle slide plating issue
9/12/2019 4:40pm What is WPC treatment? How much does it cost?
jwolfman317 Added a reply to 125/150/250/300 KTM/HUS/GG jetting thread
8/27/2019 2:49pm If I was to use these exact specs but with these exceptions: S-7 needle jet 42-75 needle , 3rd position what would you expect the results to be? I was running that originally but it was too lean below half throttle and I’m still confused by it. The S-4 needle jet is .0006” smaller than the S-7, yet the 42-74...
jwolfman317 Added a reply to 125/150/250/300 KTM/HUS/GG jetting thread
8/25/2019 5:52pm Thanks for the info, digger. What temp and elevation are these settings good for? Also, what main jet do you recommmend along with these settings?
jwolfman317 Added a reply to 125/150/250/300 KTM/HUS/GG jetting thread
8/24/2019 9:28pm They offer a 5.5, 5.75, and 6.0 for a kx 125; therefore, the 5.5 is the richest that is offered, yet still too lean for our bike. That is why I went with the 5.0 from JD Jetting.