Cordless impact to loosen tight bolts and screws?

logan_140
Profile picture for user logan_140
Posts
3724
Joined
6/9/2014
Location
Lakeland, FL, USA
logan_140
Does anybody use a cordless impact? I have a makita that would make it sooo easy to take out bolts especially subframe bolts and things that are tighter..
|
BobPA
Profile picture for user BobPA
Posts
8342
Joined
10/31/2013
Location
USA
BobPA 11/12/2017 6:37am
11/12/2017 6:37am
I use one all the time. No issue with it. You can use them to tighten bolts also. I start bolts by hand, to eliminate the possibility of cross threading. Then, I snug it with the rattle gun, and give a final torque by hand.
Acidreamer
Profile picture for user Acidreamer
Posts
1793
Joined
8/25/2015
Location
Mansfield, OH, USA
Acidreamer 11/12/2017 7:37am
11/12/2017 7:37am
I have a little 3/8 snapon one. Works great. Youll never go back to turning ratchets
imoto34
Profile picture for user imoto34
Posts
3786
Joined
1/28/2010
Location
USA
imoto34 11/12/2017 8:19am
11/12/2017 8:19am
So you have a impact that would make things easier and instead of trying it out, you seek advice on a message board?



captmoto
Profile picture for user captmoto
Posts
5925
Joined
4/22/2009
Location
Rancho Cucamonga, CA, USA
captmoto 11/12/2017 11:40am
11/12/2017 11:40am
Mostly to remove. I don't think they are a very good deal for 6mm threaded bolts.

The Shop

See All »
TrailDigger 11/12/2017 2:59pm
11/12/2017 2:59pm
Great for ramming home those shroud bolts into the radiators.
tempura
Profile picture for user tempura
Posts
2075
Joined
5/18/2015
Location
JP
tempura 11/13/2017 3:01am
11/13/2017 3:01am
If I'm in a real hurry, I'll remove them with a cordless impact drill, but back on with a T-handle or wrench.
Tracktor
Profile picture for user Tracktor
Posts
2343
Joined
8/17/2006
Location
The RTF/Amboy, WA, USA
Tracktor 11/13/2017 10:17am
11/13/2017 10:17am
One of my favorite tools ever. T-handles gather dust now..............
F150Motocrosser
Profile picture for user F150Motocrosser
Posts
3434
Joined
6/24/2014
Location
Charlotte, NC, USA
F150Motocrosser 11/13/2017 4:35pm
11/13/2017 4:35pm
BobPA wrote:
I use one all the time. No issue with it. You can use them to tighten bolts also. I start bolts by hand, to eliminate the...
I use one all the time. No issue with it. You can use them to tighten bolts also. I start bolts by hand, to eliminate the possibility of cross threading. Then, I snug it with the rattle gun, and give a final torque by hand.
This. It's one of those things that once you do it that way, you can't imagine NOT doing it that way.
mattman631
Profile picture for user mattman631
Posts
330
Joined
12/16/2015
Location
Mcalester, OK, USA
mattman631 11/15/2017 8:17am
11/15/2017 8:17am
I have used my cordless impact for years and no problems with stripping or crossthreading. I use a Porter Cable 20V, I do not attempt to torque the bolt but run them in and check them with a T handle but 9 times out of 10 they are tight. Never had one back off while riding either
harescrambled 11/16/2017 4:58pm
11/16/2017 4:58pm
I just start by hand, T-handle to run it in, then a torque wrench to finish. And yes, I torque EVERYTHING
Paw Paw
Profile picture for user Paw Paw
Posts
678
Joined
12/24/2011
Location
Benton, LA, USA
Paw Paw 11/16/2017 5:14pm
11/16/2017 5:14pm
I use one to remove bolts and nuts, but not to install them as you have no control on the amount of torque being applied.

Paw Paw
Marty1028
Profile picture for user Marty1028
Posts
988
Joined
10/5/2017
Location
Lafayette, IN, USA
Marty1028 11/17/2017 7:07pm
11/17/2017 7:07pm
harescrambled wrote:
I just start by hand, T-handle to run it in, then a torque wrench to finish. And yes, I torque EVERYTHING
so you even torque the plastic bolts to the 7ft pounds then wonder why the snap?











Im kiddingLaughing Laughing
mxracer666
Profile picture for user mxracer666
Posts
793
Joined
10/28/2010
Location
NE Iowa, IA, USA
mxracer666 11/17/2017 7:32pm
11/17/2017 7:32pm
Only if you don't mind all your bolts getting beat up and the zinc plating getting hammered off in short order...It's one thing to use them in construction, where you are installing a bolt/screw ONE time, but repeated use makes them look like crap...
harescrambled 11/18/2017 12:48pm
11/18/2017 12:48pm
Marty1028 wrote:
so you even torque the plastic bolts to the 7ft pounds then wonder why the snap?











Im kiddingLaughing Laughing
Actually, I do torque the bolts for my plastics, but then, I beat the snot out of mike bike and shit doesn't ever fall off it.

Post a reply to: Cordless impact to loosen tight bolts and screws?