Recent Activity

All

TejasTJ Added a reply to New to Dallas, getting back into the sport

9/23/2018 3:59pm
If you want some close trails to mess around on, Trophy Club Park is ok. The mx track is a joke though. Oak Hill will be your best bet for a good MX track with great dirt that’s not to far of a drive for you.

TejasTJ Started a new thread G2 Primus Handguards

8/29/2018 7:49pm
Looking to get rid of them because I don’t use them anymore. I personally think these are the best looking and peforming flag style handguards for moto. I tagged a tree with them and slightly bent one of the clamps. It doesn’t effect the performance or look. You can buy new plastic or decals to mix and match colors $25...
This forum thread has 1 reply.

TejasTJ Started a new thread Renthal 52 Tooth Sprocket 04-18 KTM

8/29/2018 7:46pm
224U-520-52 Still in really good condition, not much wear at all. $20 plus shipping. Looks like it fits big bike ktms from 04-18.
This forum thread has 1 reply.

TejasTJ Started a new thread WTB: TI or SS KTM Pegs

8/6/2018 9:49pm
Does anyone have any titanium or Stainless steel pegs they’d like to sell for a 16-18 KTM. I’m looking for something like the Raptor, Pro-Pegs, Pro SRS, SCAR.
This forum thread has 1 reply.

TejasTJ Added a reply to 2019 Moose Racing Gear

7/25/2018 5:47pm
Kinda bummed about the colorways of the Sahara Gear. As for Thor, I was really into the gear Plessinger was wearing this last weekend, until I saw it had flowers all over it on the podium.

TejasTJ Started a new thread 2019 Moose Racing Gear

7/24/2018 10:37am
Does anyone know when the release date for the 2019 Moose Racing gear is?
This forum thread has 8 replies.

TejasTJ Added a reply to Heat stroke/exhaustion

5/30/2018 8:55pm
First off, prayers for his girls and wife. This is so sad. From what I heard, his hydration pack was found empty. Friday night I decided to not make the drive to Quinlan and race this weekend. It would have been my first race in the TORN series. It was hovering around the 100’s all weekend. I believe I’ll wait...

TejasTJ Started a new thread ‘16 KTM Stuck 17mm Linkage Bolt

5/6/2018 5:48am
There is no way this linkage bolt can be this hard to remove. I’m talking about the bolt that mounts the pull rod to the frame. I’ve removed the nut no problem, which is what gives everyone problems, but the 17mm bolt will not slide out. Ive aplied penitrating oil, used a 2x4 and hammer and also tried using a...
This forum thread has 18 replies.

TejasTJ Added a reply to 97 rm125 first bike HELP!!

4/29/2018 9:11pm
The cost of the bike and everything else I had to do to it, which really wasn’t that much. $550 for a completely rebuilt motor. If you really want to ride dirt bikes and I don’t mean rip around in an open field. I would cut your loses and part it out or sell it and get a newer 125/250...

TejasTJ Added a reply to 97 rm125 first bike HELP!!

4/29/2018 5:46pm
Several years ago I had a ‘94 RM 125 that wasn’t in that bad of shape that I picked up for $500. It needed a stator and new tires. I jetted the carb because it was fouling plugs left and right. I sent the rear shock off to be rebuilt and replaced the fork seals. I rode it a lot...

TejasTJ Added a reply to ‘16 KTM Stuck 17mm Linkage Bolt

4/29/2018 10:47am
I noticed my bolt was facing a different direction than most, but I’ve also seen schematic diagrams and other ‘16’s with the bolt facing the way mine is. I finally got that sucker out. I heated it up with my proapne torch until grease was boiling out. I then drove it out with a socket (8mm) and extension just smaller...

TejasTJ Added a reply to ‘16 KTM Stuck 17mm Linkage Bolt

4/28/2018 7:07pm
Here is a picture of the bolt. The chain guide is not attached to this bolt, only the dog bone. The bolt slides out on the right side so it’s really not that much of an issue. I got off work late today but I will try a torch tomorrow.