Recent Activity
All
netsleb229 Added a reply to 2011 Crf250 resurrection XC2 Race build
4/17/2016 6:40pm How hard was it to bolt up the new style front number plate and fender?
More »
netsleb229 Added a reply to 2014 Crf450r Bog
4/15/2016 5:42am There's a little filter in the fuel pump of my crf250r. If that's all clogged up it might do what it's doing.
netsleb229 Added a reply to 6D vs Moto 9 Flex
4/13/2016 6:57pm The se4 is carbon, has mips, the bell flex's layered tech, tons of vents, it's the lightest on the market I believe, and it has a sweet paint job.
netsleb229 Added a reply to Electric powerwashers: junk?
4/13/2016 6:49pm Electric all the way. Small, quite and inexpensive. Just the right amount of pressure to get the bike clean and keep bearings intact. I bought a two stroke generator from harbor freight so I can use it at the track. Pretty sweet setup for under 200 and for that price you get a pressure washer and generator.
netsleb229 Added a reply to KTM transmission question
3/22/2016 7:31am No problem!
netsleb229 Added a reply to KTM transmission question
3/21/2016 10:40pm http://www.babbittsonline.com Put your bike into the oem parts finder then click on the part numbers you need and it will tell you what other bikes that part is the same for. I'd just make sure it's for the same application by looking at the diagram.
netsleb229 Added a reply to 2010 rmz clutch springs rubbing on clutch case
3/10/2016 5:56pm He knew about it.
netsleb229 Added a reply to 2010 rmz clutch springs rubbing on clutch case
3/10/2016 9:24am I had that happen on a yz with a magnesium clutch cover. Bought a ss cleaneable oil filter and two gallons of cheap oil. I would change it, fire it up and let it idle to get the oil warm and flush around the motor. When draining the oil I used cheese cloth to get out the metal shavings and...
netsleb229 Added a reply to Torque Question
3/5/2016 6:37pm Ohhh I see. I didn't think it through. But I didn't know that. Good info! I've always used the conversion and 180°
netsleb229 Added a reply to Torque Question
3/5/2016 5:53pm I believe you do need to compensate even if its at 90 degrees 
netsleb229 Started a new thread how to keep sprocket anodizing from wearing
2/4/2016 10:08am I'm currently in the market for some sprockets and i have always used the standard renthal aluminum sprockets without anodizing/ grey. I want to go for black but Im trying to avoid the anodizing from wearing where the chain guide is. I was wondering if anyone had any success in keeping this from happening. I figure I could trim the...
This forum thread has 13 replies.
netsleb229 Added a reply to how to keep sprocket anodizing from wearing
2/4/2016 5:10am Not riding in mud makes my season way shorter. Or at least come a lot later.
netsleb229 Added a reply to how to keep sprocket anodizing from wearing
2/3/2016 6:05pm Thanks! Ill defiantly look into that.
netsleb229 Started a new thread petcock on a 2011 crf250
5/17/2015 9:18am I realize fuel injected bikes don't have petcocks for a reason but I want to put one on my crf. The oil level seems to be raising by a little bit (1/8-1/4 in) and the oil smells of gas after sitting for a couple of days. I already change it every 5 hrs at the most and I have tried...
This forum thread has 9 replies.
netsleb229 Added a reply to petcock on a 2011 crf250
5/17/2015 9:18am I just went to smell my dad's crf450x and he uses the same oil and his smelled the same as mine. He always run it out of gas before he lets it sit and the petcocks always off. I think I'm an idiot and take things too far lol. Also I forgot to mention I tried the flame test and...
netsleb229 Added a reply to petcock on a 2011 crf250
5/17/2015 9:12am I cleaned the injector and put in some fresh oil. Started the bike and turned it off to check oil level. I gave it a bit of a sniff and found it still smelled a bit. Does the smell of oil change when it's used? Not so much to a gas smell but just a different smell from in the...
netsleb229 Added a reply to petcock on a 2011 crf250
5/17/2015 6:27am Thank you for telling me it won't work lol. looking into cleaning the injector I didn't find much on the interweb. Whats the best way to clean it? Back flush with some cleaner and pressurized air? Or will that not work because of the check valve. A local bike shop had a sonic cleaner machine that I've used on carbs...
netsleb229 Added a reply to petcock on a 2011 crf250
5/16/2015 7:37pm I haven't read anything of a guranteed fix when the injector is cleaned. I'll probably do that tomorrow but I would still like the peace of mind that there is no fuel there to leak.
netsleb229 Added a reply to Unpopular Opinions
12/19/2014 6:08pm *Tyler Bowers* oh wait popular opinion On that point Ken roczen is a shallow complaining "Californian" (accourding to twmx) and always has the stupidest look on his face
