Recent Activity
All
gameover Added a reply to 300 kit '13 250sx pros and cons
4/23/2016 5:25pm Wow, just came back from riding my 2015 husqvarna tc250 with the 300 cc kit and wow. I had the 38mm carb before the kit and it robbed if from low end torque but had huge top end power....revved like crazy. Initial impressions were that it had a lot of low end grunt. I was able to run it on...
More »
gameover Added a reply to ktm 300 sx jetting
4/6/2016 8:23pm What pre mix oil are you using? And what ratio?
gameover Added a reply to 300 kit '13 250sx pros and cons
3/30/2016 8:30pm I got mine at slavens racing. They have it for $900 with a flat rate shipping of 12 bucks and some change. 
gameover Added a reply to 300 kit '13 250sx pros and cons
3/30/2016 11:00am Just bought the 300 kit for my 2015 husqvarna tc250.
gameover Added a reply to 300 kit '13 250sx pros and cons
3/29/2016 10:44pm I blew my top end and am considering getting the 300sx kit. What oil fuel mixture do you guys recommend? I run mogul 800 40:1. Is there any special mixture to not blow my top end again?
gameover Started a new thread WTB ktm/husqvarna 250sx/tc250 cylinder
3/24/2016 10:35am Dont know where else to post this, but, I am looking to buy a 2007 or newer ktm 250sx cylinder if anyone is selling one. Please....
This forum thread has 0 replies.
gameover Started a new thread 2015 Husqvarna TC250 top end
3/15/2016 12:38pm Hi guys! So I have lost compression on my stock bike with only 26hrs on it. I'd like to find exactly where the leak is because I can hear air leaking out of somewhere when I kick start it with my hand (yes I can actually turn the motor with my hand). However, if chasing the leak will be harder...
This forum thread has 20 replies.
gameover Added a reply to 2015 Husqvarna TC250 top end
3/3/2016 2:24pm ....I'm beggining to think that the motor might have to come off too. I just sent the head to Eric Gorr and it would suck if pieces of the rings screw everything again.
gameover Added a reply to 2015 Husqvarna TC250 top end
3/3/2016 7:39am I think you're right on target. Look at the piston rings: half of the top ring is missing! 
gameover Added a reply to 2015 Husqvarna TC250 top end
2/27/2016 5:46pm Bike stalled on the face of a jump. Lost compression and wouldn't start. Perhaps, dirt came theough the carb or pushed in through the exhaust port during power washes 
Now am faced with the dilemma of fixing this or just getting the 300cc kit from husky.
Now am faced with the dilemma of fixing this or just getting the 300cc kit from husky.
gameover Added a reply to 2015 Husqvarna TC250 top end
2/27/2016 10:41am
gameover Added a reply to 2015 Husqvarna TC250 top end
2/27/2016 9:13am So I went with the vertex piston. Tore the top end apart and here's what I found: My gut feeling is that I need a new head too...? 
gameover Added a reply to 2015 Husqvarna TC250 top end
2/22/2016 5:41am I used the bike on the track, washed it with my pressure washer at home, and when time came to start it up I noticed how soft the kick starter was and could not get the bike to start. Dried up the bike with a cloth and let it be. A couple days later I started it up with no...
gameover Added a reply to ktm 2015 sx250 jetting
10/20/2015 12:38pm Hey hey, not a problem. I guess your son loves how the bike pulls now? I originally had ZipTy Racing do my suspension....after riding your son's bike I tried to get some support from ZipTy Racing with no success. I got frustrated with them and went ahead and sent it off to Factory Connection.... So after spending about $650 having...
gameover Added a reply to ktm 2015 sx250 jetting
9/22/2015 7:00pm You're missing the 38mm carb. She won't rip until you do that. I got a 15 tc250 with a full bills and a 38mm carb....she rips!
gameover Added a reply to KTM 250 SX Carb Swap
9/16/2015 7:01pm Sorry. The link is for the carb schematic of a 2014 125sx If you're good with eBay stuff then go for it. I bought a new 2015 tc125 carb for my tc250 and don't regret it
gameover Added a reply to KTM 250 SX Carb Swap
9/16/2015 6:33pm https://www.rockymountainatvmc.com/oem-schematic/2 Select carburetor You want part number 50331101544 Once you get it bring the old carb's jets to the new one and, if you haven't done so already, get the necj needle for a 2008 rm250, put the clip on the 3rd clip from bottom to top, and install that needle on the new carb as well. You will thank...
gameover Started a new thread Pro circuit platinum 2 dented from factory?
9/16/2015 2:59pm Just received this pipe from rockymountainatv for my 15 tc250. Is this dent normal? Was super excited 
This forum thread has 5 replies.
gameover Added a reply to Pro circuit platinum 2 dented from factory?
9/11/2015 5:51pm Just heard back from rockymountainatv and they said it was there for clearance purposes. I'm still gonna put it on and see if this is true. Thanks for the suggestion.
gameover Added a reply to Bone stock RM 250 FMF vs. Bills pipe
9/6/2015 8:47am Agreed. I just ruined my bills pipe works pipe (cone look) from a fall. Thinking of going back to FMF.