Lives in:
Greenville, NC, USA
Member Since:
8/18/2023
Recent Activity
All
dansfx Added a reply to KTM CUO - Lit Pro - Any others actively using this?
5/6/2026 5:21pm No I don’t think it can do starts.
More »
dansfx Added a reply to KTM CUO - Lit Pro - Any others actively using this?
5/5/2026 6:25am So I can log all that you stated with CUO, but a regular Litpro setup cannot as it doesn't have a interface to the ECU to pull that data.
dansfx Added a reply to KTM CUO - Lit Pro - Any others actively using this?
4/28/2026 5:44pm I have not tried a heart rate monitor. You have to cross the finish line 2x for the lap to count. Most of the tracks I ride you enter the track after the finish line so you do 98% of a lap before crossing the finish line for the 1st time so that lap doesn’t get logged.
dansfx Added a reply to KTM CUO - Lit Pro - Any others actively using this?
4/28/2026 1:43pm I use the CUO. What are your questions?
Tyler D Liked a reply to forum topic 2025/2026 Honda CRF450R Recall?
4/3/2026 7:42pm
first aston martin and now this. come on honda
This forum topic has 54 replies.
dansfx Added a reply to I love my 350
3/9/2026 5:44am My '23 with 66 hours doesn't have any rust on the bolts. I wash it after every ride and blow it off with the air compressor so no water is left setting on the hardware.
dansfx Added a reply to Luxon or ProTaper Independent Bar Mounts
3/1/2026 7:20pm I’m a fan of them on my 350. They definitely reduced the vibration
dansfx Added a reply to Tools for WP XACT PRO 7548 Servicing - 26 Factory Edition Forks.
2/25/2026 7:28am I'm not sure what tools you already have but you will want: WP fork cap wrench 48mm fork seal driver Various vice soft jaws Fork compression tool for cone valves (Race Tech makes the only one I'm aware of) Race Tech Compression tool This kit from Rocky Mount has most of the other tools you'll need, but the included compression...
lowmass Liked a forum topic Possible FIX for Triumph TF transmissions
2/24/2026 8:15am
Wasn’t expecting to get to this for at least a week or so but had time today and went for it. This will be a bit long…… I found 2 obvious problems and some other lesser but likely useful stuff. FORTUNATLY ALL ARE FIXABLE! It does not look like we have a design problem here, just some bad parts. This has been a consistent theme with these bikes. Anyway, armed with the following info I have confidence based on past experience that anyone good with their hands can make their Triumph shift well, avoid the death sentence of false neutrals...
This forum topic has 29 replies.
dansfx Added a reply to Need help ID ing these pegs.
2/2/2026 7:23pm Glad you got it figured out. Someone dropped some cash on those bad boys.
Darrin Willis Liked a reply to forum topic 26.5 factory editions
1/27/2026 5:56am
Holy shit you own a lot of bikes
This forum topic has 66 replies.
Mr. Plump Liked a reply to forum topic 26.5 factory editions
1/27/2026 5:56am
Ok, so I rode my buddies 2026 FC250 Factory Edition. For context, I currently own a 2022 YZ250F, 2023 YZ125X, 2023 Beta 300 Race Edition, 2024 KX450, 2024 Beta 450RX, 2024 KTM 350 SX-F, 2024.5 FC450 Factory Edition, 2025 Beta 430 X-Pro, and a 2025 YZ450F (amongst others that are not relative to this conversation). I was riding at Southfork MX and I had my 2024 Beta 450RX and my 2025 YZ450F (which had zero hours on it before the day). The track was much deeper than usual and got very techy, with some awesome ruts and braking/acceleration chop. The...
This forum topic has 66 replies.
dansfx Added a reply to How often do you guys change your graphics, and do you switch styles over the time?
1/26/2026 7:53am I do new plastics and graphics about every year. I like the stock KTM shroud graphics so I stick with those. For the number plates there is a SKDA design I like so I always replace them with the same ones.
dansfx Added a reply to Aftermarket triple clamps worth the $?
1/22/2026 6:46am I'm just a slow C rider but can't say I could tell any noticeable difference in comfort or compliance when I went from the stock KTM clamps to the Luxon clamps on my 350, but I didn't do a back-to-back test. I went with the 23.5* offset and that made a huge difference in the stability of the bike. I...
dansfx Added a reply to Data acquisition on new bikes and or factory bikes.
1/16/2026 7:28pm I have the CUO on my KTM 350 and I can track all that stuff with the exception of the suspension and clutch. It’s neat to see. I’ll think that I have the bike screaming through a section of the track and then look at the data to see it was only turning 9k RPMs lol. I’m sure the factory...
dansfx Added a reply to HELP!! CRF450 CLUTCH ISSUE ??
1/6/2026 12:36pm Check that the primary gear coming off the crank shaft is OK and the nut is tight. Also, pull the pressure plate off and check that the nut that holds inner and outer baskets on the transmission input shaft it tight. If all that's good check that the slave cylinder doesn't have some type of damage preventing the clutch from...
dansfx Added a reply to Anyone tried the ktm connectivity unit on 23 or newer?
1/4/2026 4:22pm Just once and my understanding is that only the ‘23s require the update. The ‘24 and up work without requiring an update.
PRM31 Liked a reply to forum topic Vortex ECU on 23+ KTM 350SXF
12/16/2025 6:11am
If the weather cooperates this week, I’ll follow up with how the XPR flange works with a 250 FMF header.
This forum topic has 60 replies.
dansfx Added a reply to Vortex ECU on 23+ KTM 350SXF
12/15/2025 6:36pm If you’re looking for a little more bottom end consider the XPR exhaust flange. It made a noticeable difference on my ‘23 350 with both throttle response and low end power. XPR exhaust flange
cwel11 Liked a reply to forum topic Loading bikes in tall trucks.
12/11/2025 12:12pm
Get a step ramp. They’re awesome
This forum topic has 65 replies.