Added reply in a thread 96 cr250, 92 Stanton theme, ride update 1/24/2019 8:05 AM

I used the stock 96 bottom clamp to avoid modifying steering stops and 2004 top clamp for the rubber mounted handlebar clamps. To use the 96 bottom clamp you must make a 0.020 shim (2 layers of soda can) around the forks.

Added a comment about feature 12 Days of MXmas: Stacyc 12/6/2018 10:46 AM
cmhall90usmc

Really like this what a great idea

-1 0 1

This feature has 276 comments.

Added reply in a thread 96 cr250, 92 Stanton theme, ride update 8/1/2018 6:39 PM

Forgot to tell you later in my assembly I encountered a problem with the rear brake line alignment with the newer master cylinder, you have to remove some material from the top of the master cylinder to get the brake line at the proper angle to avoid ... more »

Liked a bike check 2016 dream bike build 7/26/2018 10:26 AM
2016 dream bike build
Added reply in a thread 96 cr250, 92 Stanton theme, ride update 7/15/2018 6:23 AM

Very simple, get a 1997-1999 cr250 rear caliper hanger and rotor. Buy a late model Yz caliper banjo bolt, stock bolt won't clear the swingarm.

Added reply in a thread 96 cr250, 92 Stanton theme, ride update 7/13/2018 5:30 PM

Added reply in a thread 96 cr250, 92 Stanton theme, ride update 7/13/2018 4:07 PM

I still have my stock 96 forks I could measure for you if needed

Added reply in a thread 96 cr250, 92 Stanton theme, ride update 7/13/2018 4:06 PM

I have the crf250 forks on mine, I'm around 180lbs also. I didn't have much time to play with the clickers but should be able to this weekend.

Added reply in a thread 96 cr250, 92 Stanton theme, ride update 7/13/2018 6:31 AM

I did the shims with the 96 bottom clamp.

Added reply in a thread 96 cr250, 92 Stanton theme, ride update 7/12/2018 5:46 PM

My pipe came today I'm pretty happy with it, pacific crest did a good job.

Added reply in a thread 96 cr250, 92 Stanton theme, ride update 7/8/2018 8:43 PM

I got a chance to ride the bike today and it didn't go as I hoped. I could feel every little bump on the track to the point where I didn't feel comfortable getting up to speed and jumping. The forks felt extremely harsh. If any of you guys that have ... more »

Added reply in a thread 96 cr250, 92 Stanton theme, ride update 6/10/2018 2:10 PM

They seem very good so far, yes they're from England.

Added reply in a thread 96 cr250, 92 Stanton theme, ride update 6/9/2018 2:35 PM

I got the bike basically finished but when I took it out for a shakedown run I developed a hole in the pipe, shipped the pipe to pacific crest today

Added reply in a thread Radiator Repair Suggestions 5/24/2018 6:31 PM

Here's a before and after that was done mostly by ICW. They fixed a broken spout also

... more »
Added reply in a thread I bought a 2006 CRF450R and polished it up 5/23/2018 7:19 PM

Good work

Added reply in a thread 96 cr250, 92 Stanton theme, ride update 5/21/2018 3:44 PM

I decided to send my radiators to ICW rather than go the eBay route. I can't recommend these guys enough. They had to do some welding and straightening to both radiators and I had them back 6 days after I dropped them off at the post office.

... more »
Added reply in a thread 95 Honda CR250 forks and clamp swap 5/15/2018 6:55 PM

Just get up to 2008 Honda forks and read up on the brakes and wheel spacers needed. If anyone gives you a hard time about shimming the lower clamp tell them factory Honda did it

Added reply in a thread 96 cr250, 92 Stanton theme, ride update 5/12/2018 6:09 PM

Started putting all the fluids in today to hopefully get it running but unfortunately my right radiator has developed a leak at the spout that goes to the water pump. Now the question is do I send it off for repair? Buy a used radiator hoping it works? ... more »

Added reply in a thread 96 cr250, 92 Stanton theme, ride update 5/12/2018 2:30 PM

For now I'm just using an L bracket