2027 CRF450R

mxracer515
Posts
92
Joined
8/13/2015
Location
Drexel, MO, USA
19 hours ago

CRMX105  7hrs when it happened. & only has not started correctly 1 time     My friends was less that 1 hour.

gscx , mine will ping a bit down low in a tight corner. I'm glad you mentioned the in gear rpm changing .I had forgot to mention it.

 I raise idle but compromised & set idle bit lower than I would like in neutral. so its not so high in gear otherwise. I haven't had stalls on track even with lower idle.

crmx105
Posts
707
Joined
5/7/2016
Location
Dunnellon, FL, USA
19 hours ago
mxracer515 wrote:
CRMX105  7hrs when it happened. & only has not started correctly 1 time     My friends was less that 1 hour.gscx , mine will ping...

CRMX105  7hrs when it happened. & only has not started correctly 1 time     My friends was less that 1 hour.

gscx , mine will ping a bit down low in a tight corner. I'm glad you mentioned the in gear rpm changing .I had forgot to mention it.

 I raise idle but compromised & set idle bit lower than I would like in neutral. so its not so high in gear otherwise. I haven't had stalls on track even with lower idle.

5.2 hr on mine. Haven't had the decomp issue so far. Stalling issue has improved now that bike has more time on it. Think mapping could be cleaner. Seems like map 2 runs the cleanest.

FGR01
Posts
6178
Joined
10/1/2006
Location
USA
15 hours ago
Anyone using a torque wrench for that second drain bolt? I imagine 8-10nm is about right. I have a CDI Torque that is 4-26nm for stuff...

Anyone using a torque wrench for that second drain bolt? I imagine 8-10nm is about right. I have a CDI Torque that is 4-26nm for stuff like this. I also need to find the washers, no one stocks those by me, 2 weeks out on motorsport.com;  all the rest of the parts for an oil change are the same, so far as I can tell. 

Are you talking about the big 14mm sealing washer on the bottom or the smaller 6mm one on the left side cover?

Broseph
Posts
1237
Joined
4/28/2018
Location
Sand City 100, ID, USA
15 hours ago
gscx wrote:
I put some good time on the bike Sunday.The idle is an issue. The bike very clearly increases the RPM when you put it into gear...

I put some good time on the bike Sunday.

The idle is an issue. The bike very clearly increases the RPM when you put it into gear and I think this is part of the reduced engine breaking everyone is talking about. Problem is the difference is so much that in order for it to not stall out (which it still does a lot) the idle in gear is crazy high. I think the decomp may be part of this as well like it engages at too low of an rpm. Does anyone else get loud chirping when the bike is down low in RPMs?

It is fast and gearing is high. I've gotten used to it but might need one more tooth on the rear for some people. 

Handling seems fine, Track wasn't too rough but was fast and didnt get any headshake. Suspension seems ok too. Dont be afraid to go out on rebound. It seems heavy. 

Its a good bike, a little more honda than I had hoped, but the quality is great.

Funny you mention the idle increase. My ‘27 Yamaha also increases idle speed when in gear and also has almost no engine braking. This was the first time I noticed a bike doing that. Pretty cool honestly. I’m not a fan of engine braking. 

1

The Shop

yamathumb
Posts
236
Joined
3/11/2025
Location
Redding, CA, USA
9 hours ago

Good thing someone figured out to bump the bike past the compression stroke and retry starting. Lol......

1
1
sandtrack315
Posts
2876
Joined
7/19/2013
Location
Philadelphia, PA, USA
7 hours ago
Anyone using a torque wrench for that second drain bolt? I imagine 8-10nm is about right. I have a CDI Torque that is 4-26nm for stuff...

Anyone using a torque wrench for that second drain bolt? I imagine 8-10nm is about right. I have a CDI Torque that is 4-26nm for stuff like this. I also need to find the washers, no one stocks those by me, 2 weeks out on motorsport.com;  all the rest of the parts for an oil change are the same, so far as I can tell. 

FGR01 wrote:

Are you talking about the big 14mm sealing washer on the bottom or the smaller 6mm one on the left side cover?

Smaller 6mm!

FGR01
Posts
6178
Joined
10/1/2006
Location
USA
5 hours ago
Anyone using a torque wrench for that second drain bolt? I imagine 8-10nm is about right. I have a CDI Torque that is 4-26nm for stuff...

Anyone using a torque wrench for that second drain bolt? I imagine 8-10nm is about right. I have a CDI Torque that is 4-26nm for stuff like this. I also need to find the washers, no one stocks those by me, 2 weeks out on motorsport.com;  all the rest of the parts for an oil change are the same, so far as I can tell. 

FGR01 wrote:

Are you talking about the big 14mm sealing washer on the bottom or the smaller 6mm one on the left side cover?

Smaller 6mm!

Partzilla says they have it in stock:  https://www.partzilla.com/product/honda/90404-HW1-670

I've used these bulk ones from Amazon for years with success.  Not sure the outer diameter of the Honda OEM one, 10mm or 12mm.  Looks 12mm in pictures.  Measure your current one.   https://www.amazon.com/uxcell-Copper-Washer-Sealing-Fastener/dp/B01LXD5PYF/ref=sr_1_21?th=1

Looks like they also have the correct size 14mm one   14x20x1mm

1
Honda820
Posts
38
Joined
10/6/2020
Location
Wilkesboro, NC, USA
15 minutes ago
yamathumb wrote:

Good thing someone figured out to bump the bike past the compression stroke and retry starting. Lol......

No, let’s go ahead and hook jumper cables to a battery that’s not meant for jumper cables 🤦🏻‍♂️🤦🏻‍♂️. People panicked for no reason. Good call on your part 

Honda820
Posts
38
Joined
10/6/2020
Location
Wilkesboro, NC, USA
4 minutes ago Edited Date/Time 3 minutes ago
gscx wrote:
I put some good time on the bike Sunday.The idle is an issue. The bike very clearly increases the RPM when you put it into gear...

I put some good time on the bike Sunday.

The idle is an issue. The bike very clearly increases the RPM when you put it into gear and I think this is part of the reduced engine breaking everyone is talking about. Problem is the difference is so much that in order for it to not stall out (which it still does a lot) the idle in gear is crazy high. I think the decomp may be part of this as well like it engages at too low of an rpm. Does anyone else get loud chirping when the bike is down low in RPMs?

It is fast and gearing is high. I've gotten used to it but might need one more tooth on the rear for some people. 

Handling seems fine, Track wasn't too rough but was fast and didnt get any headshake. Suspension seems ok too. Dont be afraid to go out on rebound. It seems heavy. 

Its a good bike, a little more honda than I had hoped, but the quality is great.

The idle settings do need some tweaking and I believe it’s the culprit for the decompression issue. It believe the idle is way to low when it’s cold, therefore the decompression system is engaging when it shouldn’t. That causes the bike to stop between TDC and there’s to much compression for the starter to turn the bike over. If you rotate the engine around and get the bike off TDC, then everything works like it’s supposed to. I’ve been running my idle high from day one with no stalling or starting issues. I have 8 hours on the bike now. Honda needs to adjust the ECU so that the bike idles better. Anyway, enjoy the bike! 👍

Post a reply to: 2027 CRF450R

The Latest