How do I clean carbon buildup in 2 stroke pipes/silencers

kawasa84
Posts
1849
Joined
6/7/2008
Location
Flower Mound, TX, USA
Ok, so I have 2 05' KX250's, 1 06' KX250 and 2012 YZ125. Tried to buy pipes (Pro Circuit or FMF) and they can't seem to get around to making these according to some of the mx sales outlets. So, I want to try and clean out some of them I have. I've for 7 FMF's and 3 Pro Circuits, so any knowledge on how best to get this done. I think it's possible to blast the insides of these to do it. Any help, appreciated.
|
Orange
Posts
46
Joined
2/9/2019
Location
USA
4/28/2022 4:15am
kawasa84 wrote:
Ok, so I have 2 05' KX250's, 1 06' KX250 and 2012 YZ125. Tried to buy pipes (Pro Circuit or FMF) and they can't seem to...
Ok, so I have 2 05' KX250's, 1 06' KX250 and 2012 YZ125. Tried to buy pipes (Pro Circuit or FMF) and they can't seem to get around to making these according to some of the mx sales outlets. So, I want to try and clean out some of them I have. I've for 7 FMF's and 3 Pro Circuits, so any knowledge on how best to get this done. I think it's possible to blast the insides of these to do it. Any help, appreciated.
I have used a kiln to burn it out, a plumbing torch with MAPP gas can work, best way it to get it hot, the carbon will liquify and pour out. I have heard of guys throwing them in a fire too, never tried that one personally.
Timo
Posts
1515
Joined
1/9/2021
Location
Wichita, KS, USA
4/28/2022 4:20am
I had my 04 kx250 pipe soaked in a vat at a machine shop, came out with zero carbon. If the pipes are painted, it'll strip them to bare metal so you have to repaint it.
38special
Posts
685
Joined
6/30/2010
Location
USA
4/28/2022 8:12am
I use oven cleaner. Let it soak and then blast it out with a pressure washer. You have to repeat 2-3x, but it comes out nice and clean.

It's a bit of a pain, but this is the only do-at-home method I've found that works.
4/28/2022 8:15am
Leaner jetting, better oil, WOT!
4

The Shop

500 Mike
Posts
1150
Joined
4/1/2008
Location
Kingwood, TX, USA
4/28/2022 8:21am
I use the plumbing torch method on the core and use a wire brush on it after it cools to get all the ash off it. It takes a little time and will get smokey but does a good job.
mattyhamz2
Posts
11656
Joined
7/6/2015
Location
So Cal, CA, USA
4/28/2022 8:25am
I found video saying to put rocks in it, heat it up and shake it around. I tried it once and definitely got carbon out of it, but it took a good amount of time. I ended up just saying screw it and stopped.
GrapeApe
Posts
9139
Joined
6/7/2010
Location
Mc Kinney, TX, USA
4/28/2022 9:20am
mattyhamz2 wrote:
I found video saying to put rocks in it, heat it up and shake it around. I tried it once and definitely got carbon out of...
I found video saying to put rocks in it, heat it up and shake it around. I tried it once and definitely got carbon out of it, but it took a good amount of time. I ended up just saying screw it and stopped.
That's what we used to do. Fill it with pebbles or coarse sand, heat it and shake it.
SB215
Posts
19
Joined
6/11/2020
Location
St. Joseph, MO, USA
4/28/2022 9:54am
Rocks/pebbles was my old school method as well. Put some gas in, hold and cover the ends with your hands and palms and shake well. Repeat 2 or 3 times. Might want to be careful using the heat with this method though!
38special
Posts
685
Joined
6/30/2010
Location
USA
4/28/2022 10:22am
Leaner jetting, better oil, WOT!
When you buy a used bike and the pipe is good, sometimes you have to clean it.
FWYT
Posts
3575
Joined
5/25/2014
Location
San Diego, CA, USA
4/28/2022 1:04pm
Torch method here, as well.
1
MyBobbym
Posts
725
Joined
11/23/2020
Location
Apache Junction, AZ, USA
4/28/2022 1:23pm
kawasa84 wrote:
Ok, so I have 2 05' KX250's, 1 06' KX250 and 2012 YZ125. Tried to buy pipes (Pro Circuit or FMF) and they can't seem to...
Ok, so I have 2 05' KX250's, 1 06' KX250 and 2012 YZ125. Tried to buy pipes (Pro Circuit or FMF) and they can't seem to get around to making these according to some of the mx sales outlets. So, I want to try and clean out some of them I have. I've for 7 FMF's and 3 Pro Circuits, so any knowledge on how best to get this done. I think it's possible to blast the insides of these to do it. Any help, appreciated.
Run Blendzall at 50:1. Problem solved before the carbon build up even begins
1

Post a reply to: How do I clean carbon buildup in 2 stroke pipes/silencers

The Latest