Yz125 meltdown

Edited Date/Time 11/13/2020 2:03am
Hi,

I was riding my yz125 last weekend and i did not have any problems after 1.5 lap the bike shut off and i smelled the crank stuffers so i knew the big end was roasted.

Last night i pulled the cylinder off and the piston is partly molten.




How could this have happened and how can i prevent it from happening another time?
|
11/9/2020 5:15am
Forgot to mention that the engine was rebuild 12 hrs ago. New piston new cylinder plating.

2 hrs ago i pulled it apart and everything was still looking good and put a new piston ring in it.
I have been running the same fuel oil combo for 20 hrs.
FGR01
Posts
6181
Joined
10/1/2006
Location
USA
11/9/2020 5:41am
It got hot somehow. Either very lean or lack of oil, or possibly sucked coolant at the head o-rings.

Lean - could have developed an air leak. But, man, I suspect an air leak of that magnitude you would have had severe bogging before she let go.

Oil - take the gas you had in the tank and do the cardboard test with it. If you put pre-mixed gas on a clean piece of cardboard and let it evaporate it will leave an oil stain. Straight gas will evaporate 100% clean. I hate to say it but that is what an engine looks like when 2-stroke oil is forgotten in the gas. I just rebuilt an engine for a guy that looked exactly like that. He swore up and down he did not forget oil. When I showed him the cardboard test with the gas I drained from his tank next to mixed gas he about crapped himself.


6
11/9/2020 6:16am
I had no air leaks the bike ran fine. And the o rings in the head looked fine and in the engine there was no sign of coolant.

There was oil in the tank i just filled it up and when i came back the first thing i checked was if there was oil in the gas.
I use Putoline RS959 and the gas turns red so i know there was oil in the gas.
11/9/2020 6:18am Edited Date/Time 11/9/2020 6:19am
The jetting was on the rich side with a 445 mian jet.

The Shop

Factor E
Posts
988
Joined
9/22/2011
Location
So Cal, CA, USA
11/9/2020 6:40am
Are you sure you had timing/stator in same spot as when you took it apart?
11/9/2020 6:56am Edited Date/Time 11/9/2020 6:56am
Yes when i split the engine last night the stator was in the same position.
Nothing vibrated out of place and all the bolts were tight.
Paw Paw
Posts
678
Joined
12/24/2011
Location
Benton, LA, USA
11/9/2020 7:54am
I am sorry, but what I see on the piston took longer than 1.5 laps to develop and happen. It was running too lean and also had a serious case of preignition the squash being too tight. It also looks to have been ridden in a lot of sand with some of it getting into the engine.

Paw Paw
3
FGR01
Posts
6181
Joined
10/1/2006
Location
USA
11/9/2020 10:40am
On Paw Paw's point, is there any evidence of sand getting past the filter? Any sand stuck inside the airboot or carb?
LKHill
Posts
851
Joined
9/8/2020
Location
USA
11/9/2020 12:32pm Edited Date/Time 11/9/2020 12:33pm
Plugged jet or bad fuel if what you are saying is true. You sure would have heard it hammering before that mess.
11/9/2020 6:28pm Edited Date/Time 11/9/2020 6:30pm
That exhaust crown is eroded pretty bad. Deto
But also thats some carbon on the big end!
DynoDan22
Posts
769
Joined
9/7/2011
Location
Victorville, CA, USA
11/9/2020 7:01pm
Good Lord! That tranny oil looks like it was drained out of an RTA bus. Well used!! She was pinging for a while before it let loose. I see this a lot as the weather changes and things get a little cooler. Detonation creates a ton of heat and load on the bottom end rod bearing. That big end got warm and melted the stuffers, which appears to be carbon on the rod. That's actually melted plastic. After blowing up a few 125's as a kid, I learned quickly to recognize the sound of the motor pinging itself to death. Chicken or the egg....that piston showed signs of detonation for a few rides until the lower rod bearing gave up the ghost, flung debris up into the transfers and finished it off.
11/9/2020 11:02pm Edited Date/Time 11/9/2020 11:06pm
Thank you for all the reply's.

The last 4 times i have been riding in deep sand somewhat like Lommel. The air filter get changed every ride and there has been no evidence of any sand anywhere.

I never heard anything suspicious and dont know how pinging sounds. Only what it looks like when its broken.Unsure

The water pump is still working but something got super hot.

In the picture the tranny oil looks real bad in the picture because of the lighting.
It was 4 hrs old but the clutch is coming to its end.
sandman768
Posts
8311
Joined
3/21/2014
Location
Saratoga Springs, NY, USA
11/10/2020 6:11pm
Deep sand and possible cool temps will push it over the edge if you did not compensate with richer jetting and a splash of race gas. I ride a lot of deep sand, very heavy load on the engine, start out with rich jetting & work your way to leaner if needed.
2
11/10/2020 10:58pm
Thank you,

I have bought a bigger jet and my crank should be done today.

I will test with a higher octane gas but race gas is almost impossible to buy in the Netherlands.
ron36
Posts
100
Joined
12/17/2016
Location
BE
11/10/2020 11:37pm Edited Date/Time 11/10/2020 11:39pm
Aral 102 from germany should be fine, raced with that fuel in 125 and 250 2strokes for years. Racefuel is to expensive here.
Or mix with avgas.

Is the head insert a stock one from vhm?
Maybe squish to small, jetting te lean, of a leak.
But throw the putoline away and get some motul 800, nothing better than that,
11/10/2020 11:55pm Edited Date/Time 11/10/2020 11:56pm
I am first going to try racing 100+ from the Netherlands. Driving to Germany isnt cheap and with the restrictions right now not a good idea.

I have the insert that is 1 size smaller then the stock one. The squish is around 0,9 to 0,95 mm.

The putoline always has worked fine for me and friends. And i still have 12 liters of RS959.
LKHill
Posts
851
Joined
9/8/2020
Location
USA
11/11/2020 11:54am
Thank you for all the reply's. The last 4 times i have been riding in deep sand somewhat like Lommel. The air filter get changed every...
Thank you for all the reply's.

The last 4 times i have been riding in deep sand somewhat like Lommel. The air filter get changed every ride and there has been no evidence of any sand anywhere.

I never heard anything suspicious and dont know how pinging sounds. Only what it looks like when its broken.Unsure

The water pump is still working but something got super hot.

In the picture the tranny oil looks real bad in the picture because of the lighting.
It was 4 hrs old but the clutch is coming to its end.
4 rides in the heavy sand with it detonating will cause the damage depicted. Load is more octane sensitive than jetting. Improve your fuel quality under those conditions or you had a plugged jet like I said.
1
1
LKHill
Posts
851
Joined
9/8/2020
Location
USA
11/11/2020 1:50pm
I am first going to try racing 100+ from the Netherlands. Driving to Germany isnt cheap and with the restrictions right now not a good idea...
I am first going to try racing 100+ from the Netherlands. Driving to Germany isnt cheap and with the restrictions right now not a good idea.

I have the insert that is 1 size smaller then the stock one. The squish is around 0,9 to 0,95 mm.

The putoline always has worked fine for me and friends. And i still have 12 liters of RS959.
If you can't find better fuel you need to open up the chamber with the insert. You just don't have enough octane to run that high of a CR.
11/12/2020 10:21am
The jetting was on the rich side with a 445 mian jet.
When I went to Lommel I ran a 480 main.
1
11/13/2020 2:03am
Ok thank you i will be testing the bike tomorrow with a 470 main. There is a motocross shop next to the track so i can get that 480 if needed.
LKHill
Posts
851
Joined
9/8/2020
Location
USA
11/13/2020 4:02pm
Ok thank you i will be testing the bike tomorrow with a 470 main. There is a motocross shop next to the track so i can...
Ok thank you i will be testing the bike tomorrow with a 470 main. There is a motocross shop next to the track so i can get that 480 if needed.
If you think the bike was rich going richer will not help you one bit.
11/15/2020 10:36pm
So i rebuild the engine last week and jetted the bike. In the bottom and mid the bike was rich but on top it was lean. So i went to a different needle and a 470 main.

I rode it for 2 hrs this weekend and wil look into the engine next week.
1

Post a reply to: Yz125 meltdown

The Latest