90 YZ-250 Pegs - Whats the "Wide Peg" replacement?

quiknic
Profile picture for user quiknic
Posts
843
Joined
11/30/2008
Location
Santa Clarita, CA, USA
Fantasy
403rd
quiknic
Edited Date/Time 6/13/2020 6:15am
I just picked up a 90 YZ-250 to rebuild and race, does anyone know of a new wide peg direct swap for this year? These little sticks are not going to cut it.



On my 89 CR-250 I can install the new YZ and YZ-F titanium pegs straight up but this frame has a smaller foot print on the peg mounts.
|
Rick_Art
Profile picture for user Rick_Art
Posts
58
Joined
3/16/2018
Location
Oklahoma City, OK, USA
Rick_Art 4/3/2018 9:28pm
4/3/2018 9:28pm
My '95 yz250. has the sticks too. Foot slips off, sometimes.
1
vet 26
Profile picture for user vet 26
Posts
18
Joined
4/1/2008
Location
USA
vet 26 4/4/2018 2:05pm
4/4/2018 2:05pm
I have an '89 YZ250 with pegs from an '06 YZ250 on it. I had to grind a little bit off the post that the spring goes around and they work great.
quiknic
Profile picture for user quiknic
Posts
843
Joined
11/30/2008
Location
Santa Clarita, CA, USA
Fantasy
403rd
quiknic 4/4/2018 10:03pm
4/4/2018 10:03pm
Cool, thanks for the info. I will take a look at this over the weekend. Did you use the 89 springs and pins or the 06 parts?
vet 26
Profile picture for user vet 26
Posts
18
Joined
4/1/2008
Location
USA
vet 26 4/5/2018 1:34pm
4/5/2018 1:34pm
I believe I used the 06 springs and the pins I'm not sure. It's been a few years since I built the bike.

The Shop

See All »
smx94
Profile picture for user smx94
Posts
60
Joined
11/25/2013
Location
GB
smx94 4/5/2018 2:51pm
4/5/2018 2:51pm
I used modern ktm pegs on my 81 yz 465.had to reduce them with a grinder a little , but was easy as they have moulded in spacers
MadMatt579 4/12/2018 3:46am
4/12/2018 3:46am
I think these were 2012 yz450f pegs......fit my 89 yz250 with a little mod, i think i had to squash the spring coils a bit.




quiknic
Profile picture for user quiknic
Posts
843
Joined
11/30/2008
Location
Santa Clarita, CA, USA
Fantasy
403rd
quiknic 4/12/2018 8:43pm
4/12/2018 8:43pm
I was able to grab a set from an 08 but I do not like how they setup with the spring (even when modified to fit) so I will be grabbing another set of the newer 2014-2018 pegs and trying them out. Thanks for the feedback on what you have used on your upgraded pegs.
Natester551v
Profile picture for user Natester551v
Posts
996
Joined
1/11/2015
Location
St. George, UT, USA
Natester551v 4/14/2018 10:59am
4/14/2018 10:59am
I used Fastway pegs on my 1992...opens up the cockpit a little bit, and the reversible bushing was easy to machine down to size to fit the YZ frame. I think most pegs are pretty similar in angle, but the Fastways can be adjusted for camber, etc.



scottt89
Profile picture for user scottt89
Posts
61
Joined
1/16/2013
Location
Finksburg, MD, USA
scottt89 6/11/2020 10:59pm
6/11/2020 10:59pm
Sorry to resurrect this old thread, but I'm running into a problem with my 94 YZ restore. I had a pair of '14 YZ250 pegs laying around so I cut the peg posts so that they will fit into the narrow 94 mount slot. However, I'm finding that 14 springs are very tall and I basically have to hammer these things into place to get the pin through. While they are mounted, they seem so tight, that they don't actually spring back. I've also tried to grind a little off of the top side of the peg and file the mount a bit. Is there anyone who has done this that can update this thread with any photos or offer any suggestions?




sandman768
Profile picture for user sandman768
Posts
8119
Joined
3/21/2014
Location
Saratoga Springs, NY, USA
sandman768 6/13/2020 6:15am
6/13/2020 6:15am
quiknic wrote:
I just picked up a 90 YZ-250 to rebuild and race, does anyone know of a new wide peg direct swap for this year? These little...
I just picked up a 90 YZ-250 to rebuild and race, does anyone know of a new wide peg direct swap for this year? These little sticks are not going to cut it.



On my 89 CR-250 I can install the new YZ and YZ-F titanium pegs straight up but this frame has a smaller foot print on the peg mounts.
Steel frame Honda pegs fit and has stated newer YZ pegs... on a side note: does anyone have an oem front sprocket cover like on this YZ they would sell? Yamaha used this cover for many years and for some reason I have not been able to find one on eBay. Looks like they may be available new but I”m trying to keep a resto from getting out of hand😂

Post a reply to: 90 YZ-250 Pegs - Whats the "Wide Peg" replacement?