2003 cr250 forks keep leaking

SAINT1000
Posts
89
Joined
5/26/2018
Location
Rochester, NY, USA
We have a 2003 cr250r that my son races. Every year we get the forks rebuilt, with new seals and fluid. Always use Honda seals. Anyways got the forks back this year installed them on the bike and next morning there was a small puddle under 1 of the forks. Took them back off and returned to the place that did the rebuild and he took aparts and put back togeather and said everything looks fine. A week or 2 later same thing only bigger puddle, took the back and the guy said must be a bad seal. So I bought another set of seals and had them installed. Now a week later I have a 12" spot under the same fork and now they want to charge me again for another rebuild. Why would these keep leaking. The same place has done our forks every year for the last 3 years and never had an issue untill now, what could cause this.
|
DynoDan22
Posts
769
Joined
9/7/2011
Location
Victorville, CA, USA
5/26/2020 7:05pm
There must be a nick on the fork tube somewhere that the suspension tech missed which tore the seal. Either that or the slider tube is bent/dented.
4
Keith72
Posts
394
Joined
7/17/2010
Location
Omaha, NE, USA
5/27/2020 7:39am
Check fork alignment
erik_94COBRA
Posts
1183
Joined
7/21/2016
Location
Houston-ish, TX, USA
5/27/2020 12:46pm
Did you change the bushings also?
SAINT1000
Posts
89
Joined
5/26/2018
Location
Rochester, NY, USA
5/27/2020 5:25pm
yes everything was replaced, seals, bushings, retainers.

The Shop

SAINT1000
Posts
89
Joined
5/26/2018
Location
Rochester, NY, USA
5/27/2020 5:26pm
Keith72 wrote:
Check fork alignment
alignment of what?
mxgreg85
Posts
58
Joined
4/1/2008
Location
USA
5/27/2020 5:50pm
YouTube search "dirt bike front axle alignment." There is an order in which you have to tighten everything down, compressing the forks a few times while one side is still floating on the axle, to make sure the forks are straight up and down. If you do not follow this process, you may be bringing the bottom of the forks closer together or further apart than the top instead of straight up and down, which would cause them to leak.
SAINT1000
Posts
89
Joined
5/26/2018
Location
Rochester, NY, USA
5/27/2020 5:55pm
mxgreg85 wrote:
YouTube search "dirt bike front axle alignment." There is an order in which you have to tighten everything down, compressing the forks a few times while...
YouTube search "dirt bike front axle alignment." There is an order in which you have to tighten everything down, compressing the forks a few times while one side is still floating on the axle, to make sure the forks are straight up and down. If you do not follow this process, you may be bringing the bottom of the forks closer together or further apart than the top instead of straight up and down, which would cause them to leak.
Thank you, I'll look in to that
Keith72
Posts
394
Joined
7/17/2010
Location
Omaha, NE, USA
5/27/2020 6:01pm Edited Date/Time 5/27/2020 6:02pm
Keith72 wrote:
Check fork alignment
SAINT1000 wrote:
alignment of what?
Are the fork legs perfectly parallel with each other. If they are not it can cause seals to leak. The way you install the front axle plays a big roll in proper alignment.

Just curious who your suspension guy is. Did he check for a nick or dent in the tubes? Maybe slightly bent?
Keith72
Posts
394
Joined
7/17/2010
Location
Omaha, NE, USA
5/27/2020 6:13pm
I use one of these to install the front axle.
https://www.rockymountainatvmc.com/parts/tusk-hex-axle-tool-p
Hold the axle nut and spin the axle in with this tool on a wrench until its tight. Then tighten the brake side pinch bolts leaving the opposite side loose. Now you can compress the suspension a few times to help the fork tubes align themselves. Or you can spin the front wheel and stop it quickly with the brake a few times to align them. Last step is to tighten the non-brake side pinch bolts. Make sure the axle has a light coating of grease on it before installing.
erik_94COBRA
Posts
1183
Joined
7/21/2016
Location
Houston-ish, TX, USA
5/28/2020 1:27am Edited Date/Time 5/28/2020 1:27am
Are you sure it’s leaking from the fork seal area? Could be on the bottom of fork if rebound adjuster crush ring isn’t sealing.
4
SAINT1000
Posts
89
Joined
5/26/2018
Location
Rochester, NY, USA
5/28/2020 3:15am
The forks are going back to be checked one more time and make sure fluid full, then I will mess with axle alignment
SAINT1000
Posts
89
Joined
5/26/2018
Location
Rochester, NY, USA
6/3/2020 7:21pm
He found a dent in the lower fork tube that he missed before
1
SAINT1000
Posts
89
Joined
5/26/2018
Location
Rochester, NY, USA
6/14/2020 3:20pm
OK, SO the dent he found is in the fork tube that is NOT LEAKING. he said the other leg looks perfect but was very low on oil. so i bought another set of seals and bushings, he put them togeather, and went to the race today. after the day, get the bike on the trailer and the left fork (the one without the dent is puking oil) . we aligned the axle, what could we be missing here?
Paul_Pitzonka
Posts
693
Joined
5/1/2018
Location
Grand Terrace, CA, USA
6/14/2020 3:42pm
SAINT1000 wrote:
OK, SO the dent he found is in the fork tube that is NOT LEAKING. he said the other leg looks perfect but was very low...
OK, SO the dent he found is in the fork tube that is NOT LEAKING. he said the other leg looks perfect but was very low on oil. so i bought another set of seals and bushings, he put them togeather, and went to the race today. after the day, get the bike on the trailer and the left fork (the one without the dent is puking oil) . we aligned the axle, what could we be missing here?
Is the fork tube itself straight/true?
SAINT1000
Posts
89
Joined
5/26/2018
Location
Rochester, NY, USA
6/14/2020 3:48pm
SAINT1000 wrote:
OK, SO the dent he found is in the fork tube that is NOT LEAKING. he said the other leg looks perfect but was very low...
OK, SO the dent he found is in the fork tube that is NOT LEAKING. he said the other leg looks perfect but was very low on oil. so i bought another set of seals and bushings, he put them togeather, and went to the race today. after the day, get the bike on the trailer and the left fork (the one without the dent is puking oil) . we aligned the axle, what could we be missing here?
Is the fork tube itself straight/true?
He looked and then I looked when I drops off the seals and bushings, I rolled it on the bench and didn't see any hops,
SAINT1000
Posts
89
Joined
5/26/2018
Location
Rochester, NY, USA
6/14/2020 4:11pm
just called the guy that did my forks, he works for the local honda dealer, they refered him to me saying he does all their shock work. he told me he has no idea and id have to take them some where else. this is after 2 sets of honda seals and bushings, and paying the labor, so so 300 dollars in and i still have leaking forks. awesome
RGaede
Posts
212
Joined
1/10/2014
Location
Albuquerque, NM, USA
6/14/2020 5:12pm
It may sound silly, but pop the dust cover down and make sure the seal was installed correctly. I have seen them put in backwards.
1
BToz
Posts
282
Joined
4/10/2020
Location
Nampa, ID, USA
6/14/2020 6:31pm
The forks on that bike are incredibly easy to rebuild. Get the tools (pretty cheap from rm atv/mc) and some oil and try some skf seals.
2
Keith72
Posts
394
Joined
7/17/2010
Location
Omaha, NE, USA
6/14/2020 8:07pm
BToz wrote:
The forks on that bike are incredibly easy to rebuild. Get the tools (pretty cheap from rm atv/mc) and some oil and try some skf seals.
There are a lot of videos on YouTube. It's not as hard as you think. +1 on the SKF seals.
Keith72
Posts
394
Joined
7/17/2010
Location
Omaha, NE, USA
6/14/2020 8:08pm
RGaede wrote:
It may sound silly, but pop the dust cover down and make sure the seal was installed correctly. I have seen them put in backwards.
Yup. They might be upside down.
SAINT1000
Posts
89
Joined
5/26/2018
Location
Rochester, NY, USA
6/15/2020 3:52am
RGaede wrote:
It may sound silly, but pop the dust cover down and make sure the seal was installed correctly. I have seen them put in backwards.
got the tools comming. which way is the right way for the seals,
SAINT1000
Posts
89
Joined
5/26/2018
Location
Rochester, NY, USA
6/15/2020 12:14pm
WILL 2004 CR250R LOWER FORK TUBES FIT THE 2003 CR250R UPPER TUBES.
SAINT1000
Posts
89
Joined
5/26/2018
Location
Rochester, NY, USA
6/15/2020 3:10pm
also, is it possible for the lower fork tubes to leak from the tube and the lower bracket
SAINT1000
Posts
89
Joined
5/26/2018
Location
Rochester, NY, USA
6/15/2020 4:27pm
started to take the forks out and the left side bracket(that holds axle and caliper) on thew lower end of the fork is spinning in the breeze. im thinking this is where the oil is coming from. do the make a seal for this?
BToz
Posts
282
Joined
4/10/2020
Location
Nampa, ID, USA
6/15/2020 6:08pm
Not a good sign. Maybe the allens came loose and they’re leaking past the o-rings? You need to watch the YouTube videos on “how to change fork lugs on Honda cr250”.
1
Keith72
Posts
394
Joined
7/17/2010
Location
Omaha, NE, USA
6/15/2020 8:29pm
SAINT1000 wrote:
started to take the forks out and the left side bracket(that holds axle and caliper) on thew lower end of the fork is spinning in the...
started to take the forks out and the left side bracket(that holds axle and caliper) on thew lower end of the fork is spinning in the breeze. im thinking this is where the oil is coming from. do the make a seal for this?
Will it tighten up or is it completely stripped?
Keith72
Posts
394
Joined
7/17/2010
Location
Omaha, NE, USA
6/15/2020 8:29pm
BToz wrote:
Not a good sign. Maybe the allens came loose and they’re leaking past the o-rings? You need to watch the YouTube videos on “how to change...
Not a good sign. Maybe the allens came loose and they’re leaking past the o-rings? You need to watch the YouTube videos on “how to change fork lugs on Honda cr250”.
Is there an O-ring or is there just some thread sealer on it?
jaredkeller96
Posts
503
Joined
11/8/2015
Location
Huntersville, NC, USA
6/15/2020 8:31pm
BToz wrote:
Not a good sign. Maybe the allens came loose and they’re leaking past the o-rings? You need to watch the YouTube videos on “how to change...
Not a good sign. Maybe the allens came loose and they’re leaking past the o-rings? You need to watch the YouTube videos on “how to change fork lugs on Honda cr250”.
You can run them without Allen’s. There’s two O rings on the bottoming cup. They prolly need replaced then the tube needs retorqued to the axle bracket

Post a reply to: 2003 cr250 forks keep leaking

The Latest