Are KTM's known for eating rear rotors/pads?

xc200
Posts
49
Joined
12/28/2013
Location
Astoria, OR, USA
9/2/2014 1:20pm
Have you tried different types of pads. I use sintered when I ride off road and I swear I get about 15-20 rides out of them. And this is while dragging them down long butt puckering hills.
BobPA
Posts
8342
Joined
10/31/2013
Location
USA
9/2/2014 1:23pm Edited Date/Time 9/2/2014 1:53pm
Well that sucks then about the stock pipes being known to do that. Never had a Suzuki/KX do that back in the day. Is it all...
Well that sucks then about the stock pipes being known to do that. Never had a Suzuki/KX do that back in the day. Is it all brands' stock pipes that fail like that, or just KTM?

Cheers
Simon
You never owned an 04 kx 250 did you? Mine ate pipes, stock or aftermarket.
nornevrder
Posts
679
Joined
3/20/2011
Location
Reno, NV, USA
9/2/2014 1:50pm
Anonymous wrote:
The better the pads work the faster they wear out. Same with any high performance brake system, car, bike, whatever. The pipes crack because they are...
The better the pads work the faster they wear out. Same with any high performance brake system, car, bike, whatever. The pipes crack because they are super thin and lightweight, and because the mounts get bound up when they are tightend wrong. Stresses the thin metal, I used FMF parts. Just my two cents after riding and racing KTMs for a few years.
This. I ended up slapping a FMF Fatty on mine withe a shorty silencer. Only problem I had were the bolts wanted to get loose every ride. Dabbed a little blue lock tight on the threads and the problem was solved. I am heavy on my front breaks so that may be the reason why I never had a problem with the rears. I will say that my front breaks would start singing to me in the middle of a 20 min moto due to getting hot.
Suns_PSD
Posts
989
Joined
4/1/2008
Location
Austin, TX, USA
9/2/2014 1:53pm
The stock pads last 5x longer than anything aftermarket.

The stock pipe is made of tinfoil.

The Shop

cingred
Posts
36
Joined
4/1/2008
Location
USA
9/2/2014 2:02pm
I like that idea, thanks. Might try it after I give the pedal some more play.
Cheers
Simon
Welcome. It works pretty well.
9/2/2014 3:10pm
nornevrder wrote:
This. I ended up slapping a FMF Fatty on mine withe a shorty silencer. Only problem I had were the bolts wanted to get loose every...
This. I ended up slapping a FMF Fatty on mine withe a shorty silencer. Only problem I had were the bolts wanted to get loose every ride. Dabbed a little blue lock tight on the threads and the problem was solved. I am heavy on my front breaks so that may be the reason why I never had a problem with the rears. I will say that my front breaks would start singing to me in the middle of a 20 min moto due to getting hot.
At the risk of derailing my own thread, what difference did the FMF Fatty/Shorty combo make over stock?
Cheers
Simon
9/2/2014 3:13pm
xc200 wrote:
Have you tried different types of pads. I use sintered when I ride off road and I swear I get about 15-20 rides out of them...
Have you tried different types of pads. I use sintered when I ride off road and I swear I get about 15-20 rides out of them. And this is while dragging them down long butt puckering hills.
Fearo suggested Goldfren pads and they make a bunch of sintered ones. Gonna try them out if I can work out which ones I need - not the most helpful website.
Cheers
Simon
9/2/2014 3:34pm
Fearo suggested Goldfren pads and they make a bunch of sintered ones. Gonna try them out if I can work out which ones I need -...
Fearo suggested Goldfren pads and they make a bunch of sintered ones. Gonna try them out if I can work out which ones I need - not the most helpful website.
Cheers
Simon
I would stay away from the goldfren K5 pads at least.
that is what's on my bike right now, and I dont think I will let them wear out. don't know yet how the wear is, but compared to stock honda nissin pads, they suck. Never had to press the brake this hard before.
BobPA
Posts
8342
Joined
10/31/2013
Location
USA
9/2/2014 3:43pm
I run Moose M1 pads all around (manufactured by DP) they last only ok...but man do they stop. I think you may not be aware you are dragging the brake. Try lowering the brake lever a pinch...
resetjet
Posts
2560
Joined
3/16/2012
Location
Tampa, FL, USA
9/2/2014 5:35pm
First of all, what are your riding conditions?? Water and sand eat pads big time.

For carbon pads(short life, but do not overheat easily) you will get one race out of them.
For sintered pads you get quite alot of life, but may overheat if you are a dragger or pretty fast rider.

KTM pads are better then any aftermarket I have tried.

Get the cheap closeout neutron pads from rocky mountain. They are sintered and you will get 15-20 good rides on them. I forget $9 or $12 a set.

Or cheapo tusk carbons, but I get one hare scramble out of them and they won't make it through a muddy enduro.
hartebreak
Posts
2657
Joined
9/16/2009
Location
Portland, OR, USA
9/2/2014 8:42pm
I run a rekluse on my 2012 300xc so I got thru pads probably quicker than I should but it still isn't horrible. And just like tires, the better the pads work, the quicker they wear out.
9/2/2014 8:46pm
BobPA wrote:
I run Moose M1 pads all around (manufactured by DP) they last only ok...but man do they stop. I think you may not be aware you...
I run Moose M1 pads all around (manufactured by DP) they last only ok...but man do they stop. I think you may not be aware you are dragging the brake. Try lowering the brake lever a pinch...
Yeah lowering the lever and running an extra return spring is my next step.

Cheers
Simon
9/2/2014 8:48pm
resetjet wrote:
First of all, what are your riding conditions?? Water and sand eat pads big time. For carbon pads(short life, but do not overheat easily) you will...
First of all, what are your riding conditions?? Water and sand eat pads big time.

For carbon pads(short life, but do not overheat easily) you will get one race out of them.
For sintered pads you get quite alot of life, but may overheat if you are a dragger or pretty fast rider.

KTM pads are better then any aftermarket I have tried.

Get the cheap closeout neutron pads from rocky mountain. They are sintered and you will get 15-20 good rides on them. I forget $9 or $12 a set.

Or cheapo tusk carbons, but I get one hare scramble out of them and they won't make it through a muddy enduro.
Thanks. I'm in Colorado so it's pretty much always dry when I ride, no sand/mud, which is why I'm surprised at the wear. Definitely gonna lower the brake lever and give it another return spring, but there's not much to lose with those neutron pads - right now I'd love to get 15-20 decent rides out of any pads!

Cheers
Simon
Fearo
Posts
1383
Joined
12/17/2009
Location
BE
9/3/2014 1:27am
Fearo wrote:
Sorry to say, but it is true that they eat brake pads, although I must say I am a bit of a brake dragger. The funny...
Sorry to say, but it is true that they eat brake pads, although I must say I am a bit of a brake dragger. The funny thing is, I had less trouble with them on my '11 150SX but I experience the same issues you have on my '13 250SX. The way I see it you have 2 options; Either keep blowing through (hopefully) cheaper pads, or buy some of the highest quality brake pads which will obviously cost more. In my opinion the 2 highest quality ones are the Braking CM46 Race pads or my favourites, the Golfdren S33 brake pads. I'd say I get about 20 rides out of mine.

Also, do yourself a favour and get a solid rotor with holes in it. Your braking will not suffer and your pads will last longer.
Thanks. Never heard of Goldfren but willing to try them. Can't be any worse than stock/Galfer. Any recommendations for rotors?
Cheers
Simon
No problem. Goldfren is a Czech company that tests their products in Germany to a really high standard.

The reason that your (and my) bike eats its pads is because the entire brake system generates waaaaayyy too much heat, which is the reason most pads will fail prematurely. I know heat is correlated with usage but they heat up way too fast and get rediculously hot. The goldfren S33 pads have a guaranteed thermal capacity of 800 degrees Celcius. They are the only brake pads in the world (that I know of) that make that claim.

As for rotors, I use a British made rotor that costs about $40 and is LIGHTYEARS better and longer lasting than the KTM one. I know Goldfren makes a solid rotor with holes, but I have no idea on the availability in the US. The only thing I can say is, don't get caught up in buying one of those fancy shark fin-type rotors or your pads will be going out even faster.
9/3/2014 7:49am
Fearo wrote:
No problem. Goldfren is a Czech company that tests their products in Germany to a really high standard. The reason that your (and my) bike eats...
No problem. Goldfren is a Czech company that tests their products in Germany to a really high standard.

The reason that your (and my) bike eats its pads is because the entire brake system generates waaaaayyy too much heat, which is the reason most pads will fail prematurely. I know heat is correlated with usage but they heat up way too fast and get rediculously hot. The goldfren S33 pads have a guaranteed thermal capacity of 800 degrees Celcius. They are the only brake pads in the world (that I know of) that make that claim.

As for rotors, I use a British made rotor that costs about $40 and is LIGHTYEARS better and longer lasting than the KTM one. I know Goldfren makes a solid rotor with holes, but I have no idea on the availability in the US. The only thing I can say is, don't get caught up in buying one of those fancy shark fin-type rotors or your pads will be going out even faster.
V interesting. I might be in the UK soon. What's the brand of brake rotor you use?

Cheers
Simon
markit
Posts
2641
Joined
1/10/2013
Location
Bogalusa, LA, USA
9/3/2014 8:27am
Been racing KTMs for 20 years, the answer is Yes. The race pads wear fairly quiclly on ht erear I always ran the Kevlar on the rear you loose some power but really gain a lot of control IMO.
resetjet
Posts
2560
Joined
3/16/2012
Location
Tampa, FL, USA
9/4/2014 7:17am
Simon.....You will like the neutron's on the trails........You may overheat if you are a real dragger, but they will last. A friend of mine is a real dragger and does what you said on the pedal..
loftyair
Posts
2926
Joined
7/3/2009
Location
riverside, CA, USA
9/4/2014 8:56pm
I always thought the rear brake was a bit too strong on the KTM. So, I always bought the cheapest pads I can get my hands on. Seems to make the brake better! But, there is a lot of personal preference on this matter.
9/7/2014 1:58pm
V interesting. I might be in the UK soon. What's the brand of brake rotor you use?

Cheers
Simon
Fearo wrote:
Thanks! I'm gonna try the pedal adjustment and some cheap Neutron pads first then see where I am. Gonna need to replace the disc pretty soon so might end up with the Hollis one.

Cheers
Simon
9/7/2014 1:59pm
resetjet wrote:
Simon.....You will like the neutron's on the trails........You may overheat if you are a real dragger, but they will last. A friend of mine is a...
Simon.....You will like the neutron's on the trails........You may overheat if you are a real dragger, but they will last. A friend of mine is a real dragger and does what you said on the pedal..
Nice. I'll post again when I get the Neutron pads.

Cheers
Simon
papa k
Posts
13
Joined
8/29/2014
Location
Alanson, MI, USA
9/7/2014 4:46pm
We use Vesrah VD997J they come with the insulator and work the best. Yes the pipes are bad ours cracked too All six of them we keep 5 in rotation from the bike to the welders. Also the vforce reeds will go in 10 hours or less with an A rider on the bike on the 2009-2012 bikes We replaced them with the Boyeson rad valve and they last 100 hours. The new Vforce 4's have lasted 36 hours so far and just a little chip last time I looked. Thats on the 2013
brimx153
Posts
3344
Joined
5/3/2012
Location
IE
9/7/2014 6:03pm
there s some tracks here that are sandy and if it rains you d go through a pair of back pads in one day , it might have something to do with were your riding too ,

Post a reply to: Are KTM's known for eating rear rotors/pads?

The Latest