1996 CR250 McGrath Replica Rebuild

MCfan4life
Posts
5731
Joined
6/25/2009
Location
Qld, AU
10/12/2011 7:36pm
OK so I've been back from holiday for a little over a week and settled back into the daily grind. I ventured into the garage today to do a few small jobs on the bike.

Firstly, I replaced the Pro Circuit footpegs with the Lightspeed footpegs. The Lightspeed pegs are night and day better than the Pro Circuit pegs. Bigger, sharper, more factory looking.

MCfan4life
Posts
5731
Joined
6/25/2009
Location
Qld, AU
10/12/2011 7:39pm
Then I decided to replace the hardware on my triple clamps and handlebar. You see when I sent all my hardware to the get re-zinced my triple clamps were sitting in a cupboard and I forgot about them. So I just ordered new ones as it wasn't cost effective to re-zinc 2 nuts and 4 bolts.

Before:


After:
MCfan4life
Posts
5731
Joined
6/25/2009
Location
Qld, AU
10/12/2011 7:46pm
During the above procedure however, disaster struck. I removed the bars and then the top clamp. I then placed a support under the front wheel so the forks wouldn't drop out.

During this whole rebuild process I had the frame strapped to the stand with tie-downs and forgot that, when I previously installed the triple clamps, I forgot to re-attach the tie-down in a different part of the frame. Shocked

So, even though there was support under the front wheel, as soon as I undid the bottom nut holding the triple tree in the frame, the back of the bike dropped, the front of the bike shot up in the air and this was the result...





Sad
MCfan4life
Posts
5731
Joined
6/25/2009
Location
Qld, AU
10/12/2011 7:53pm
I got it back on the stand and assessed the damage. I was VERY lucky. On the right hand side of the bike I was expecting the worst. I didn't even want to pick it up. I was expecting the pipe to be crushed.

But damage was surprisingly minimal and cosmetic. I scratched the decal on the rear guard. Easy to replace. I scratched my new Lightspeed footpeg but it's not that noticeable.

The left hand side was a different story though. I wasn't so lucky. It copped a chip and a scratch in the frame though from the forks when it let go.



I am, at this point, shattered. I don't know what to do. Getting the frame powder coated initially was a nightmare. Do I really want to strip the bike again to have it powder coated again? No. Do I want that unsightly scratch in my frame? No.

Maybe I'll just throw a cover over it for a couple of months and hope it fixes itself...

The Shop

10/12/2011 8:05pm
Surely McGrath's bike had a scratch on it some where
CamP
Posts
6826
Joined
8/16/2006
Location
Colleyville, TX, USA
10/12/2011 8:14pm
That's aggravating. A bit of white vinyl back ground material will cover that up nicely.
Hut
Posts
10281
Joined
4/27/2010
Location
USA
10/12/2011 8:22pm
Color matched white enamel applied with a small brush would probably cover that gouge alright.
newmann
Posts
24437
Joined
4/1/2008
Location
USA
10/12/2011 8:41pm


Sad
Pat327
Posts
688
Joined
2/18/2008
Location
USA
10/12/2011 9:35pm
I know exactly how you feel. I put a few little nicks in my bike's paintwork in the process of putting it back together. It hurts. Don't be discouraged, though. You've done a beautiful job.

Didn't they put AMA tech inspection stickers there, approximately?
MCfan4life
Posts
5731
Joined
6/25/2009
Location
Qld, AU
10/12/2011 9:46pm
Pat327 wrote:
I know exactly how you feel. I put a few little nicks in my bike's paintwork in the process of putting it back together. It hurts...
I know exactly how you feel. I put a few little nicks in my bike's paintwork in the process of putting it back together. It hurts. Don't be discouraged, though. You've done a beautiful job.

Didn't they put AMA tech inspection stickers there, approximately?
Hmmm good thought Pat. I'll check out some old magazines. Thanks Wink
MCfan4life
Posts
5731
Joined
6/25/2009
Location
Qld, AU
10/13/2011 12:15am
Pat327 wrote:
I know exactly how you feel. I put a few little nicks in my bike's paintwork in the process of putting it back together. It hurts...
I know exactly how you feel. I put a few little nicks in my bike's paintwork in the process of putting it back together. It hurts. Don't be discouraged, though. You've done a beautiful job.

Didn't they put AMA tech inspection stickers there, approximately?
MCfan4life wrote:
Hmmm good thought Pat. I'll check out some old magazines. Thanks Wink
Like this?

reded
Posts
3682
Joined
3/26/2011
Location
USA
10/13/2011 5:08am
OMG! I'd rather someone took a knife to the Mona Lisa. Good job covering up the damage but next time be more careful, I wanna see this thing finished.
10/13/2011 5:17am
The perfect spot for that AMA sticker and you were going to put it there anyway, weren't you?
Pat327
Posts
688
Joined
2/18/2008
Location
USA
10/13/2011 6:33am
Perfect!
dogger315
Posts
309
Joined
11/22/2010
Location
USA
10/13/2011 9:24am
Excellent solution to the scratch. I had something similar happen to my 79 CR250. I had just put it back on
it's stand and covered it with a padded flannel blanket (I coddle my dust collectors). I was heading for the
door when I heard this big boom! I turned around and there it was on the floor. It had somehow fallen off
of the stand onto it's left side - on a 79, that's the same side as the pipe. At first, I didn't even want to uncover
it and check. In the end, I was very fortunate. The only damage was a ruined OE grip and clutch lever, both
still available. The padded blanket protected all the irreplaceable parts.

I haven't been on here in a while, but I was talking to DJ the other day and wanted to get caught up. I am
very impressed with your build. The triples look great and that rear shock turned out so sweet it looks better
than brand new, same with the wheels - awesome job!

Looks like you are nearly there. Can't wait to see the finished pictures.

dogger
jimmie
Posts
2263
Joined
8/21/2008
Location
Huntington Beach, CA, USA
10/13/2011 4:12pm
The drama of this build is riveting!

Nice saveWink
MCfan4life
Posts
5731
Joined
6/25/2009
Location
Qld, AU
10/14/2011 3:34am
Thanks guys.

I'll be back into it in a few days when I'm on my next days off.
pasky411
Posts
21
Joined
10/18/2011
Location
FR
10/18/2011 3:26am
Hello im pasky,
Im new on this forum and i follow closely your Honda CR 96 rebuild..
i also did a McGrath replica signed by MC himeself...
Even if you dont understand french you can see the pics on this link of my adventure!....
enjoy....
http://mx2k.com/forum-motocross/105486/honda-250-cr-1996.html

i wait for your comments.
Erick
Posts
181
Joined
1/20/2010
Location
NL
10/18/2011 4:27am
Your bike is really awesome, I love the attention to detail.

I would suggest you put some titanium bolts here and there (engine, triple clams, front axle clamps, rear axle nut). But that would be pretty expensive.
pasky411
Posts
21
Joined
10/18/2011
Location
FR
10/18/2011 5:04am
Thanks erick,
There's some titanium bolts on it already..
On the shrouds, number plates HRC trimple clamp and gripsters.
I need to find still a nylon bar pad.........hard!.....
jtracing6
Posts
588
Joined
11/26/2009
Location
Dundalk, IE
10/18/2011 9:34am
I can't find any pictures on these links? Anyone else having problems or just me?
pasky411
Posts
21
Joined
10/18/2011
Location
FR
10/18/2011 10:18am
you checked all the pages...no?
MCfan4life
Posts
5731
Joined
6/25/2009
Location
Qld, AU
10/18/2011 3:32pm
jtracing6 wrote:
I can't find any pictures on these links? Anyone else having problems or just me?
Doesn't work for me either JT...
10/18/2011 9:23pm
classic thread hijack there, especially when the links are dead.... sad face
pasky411
Posts
21
Joined
10/18/2011
Location
FR
10/19/2011 1:05am
i dont undunstand erick did managed to see them......
pasky411
Posts
21
Joined
10/18/2011
Location
FR
10/19/2011 1:19am Edited Date/Time 10/19/2011 1:21am
Or search on goggle my post on the MX2K french
website
pasky411
Posts
21
Joined
10/18/2011
Location
FR
10/19/2011 1:40am
By the way anyway i subscribe to the vital mx forum to congratulate MC fan 4 life for your replica....very nice job!

Post a reply to: 1996 CR250 McGrath Replica Rebuild

The Latest