Recent Activity
All
Ichnusa Added a reply to 22 Yz250f settings
10/6/2025 8:48am I think it's no a technique thing It's 13 years I ride and 8 I ride motocross I've jumped many times and I have any problem with jumps both with gas when I too slow and without when I have enough speed. The idle of the engine is bone stock. I think it's a suspension thing in fact with the...
More »
Ichnusa Added a reply to 22 Yz250f settings
10/6/2025 8:19am Maybe 2 out is too slow but stock is 7 out so no that much far from stock setting. Obviously I've tryed stock configuration but the front is vague, busy and jumps front end high. I've tryed some other adjustments but the only thing that give me some results is close the rebound but with it's down sides, maybe there's...
Ichnusa Added a reply to 22 Yz250f settings
10/6/2025 7:02am Another tought is to lower fork oil height to allow the suspension to move further down in the stroke when hit bumps while mid stroke so maybe the mid stroke harshness goes away. I have about 40/60 mm of fork travel available
Ichnusa Added a reply to 22 Yz250f settings
10/6/2025 6:58am I've already tryed and I prefer the closest. With the bars further away I feel the front end vaguer. I've tryed all from the stock position to the closest position. I was thinking to open the fork reb by 2 clicks an the rear shock 2 clicks too for balance the faster rebound setting on the front. Do you think...
Ichnusa Added a reply to 22 Yz250f settings
10/6/2025 5:46am I have the same problem with stock valving. Valving don't change that much. What you would change for better handling?
Ichnusa Added a reply to 22 Yz250f settings
10/6/2025 5:29am Forks are valved and springs are original. The bars are in the closest mount and offset. I've tried cloest mount and the offset away from the rider but I prefer the closest I'm pretty short only 168cm
Ichnusa Started a new thread 22 Yz250f settings
10/6/2025 1:33am Hello everyone, I ride a 22 yz250f, the bike was wery hard to turn, it was jumping front end high and the front end feel was bad so i closed the reb 2 by 2 clicks until i reach 2 out, now the bike turns better, jumps right and it's more stable but in braking bumps and in other situations...
This forum thread has 12 replies.
Ichnusa Added a reply to Kyb free pistons
5/2/2022 12:28pm If it drains automatically during the normal use it has already do it because I have rode the bike some hours yet. But my proboem is: i bought this bike brand new and beacuse the fork was harsh fro the middle of the stroke i drain 15cc of oil from the air bleed screw i ride the bike and it...
Ichnusa Added a reply to Kyb free pistons
5/2/2022 12:07pm I read in the internet that from the 2018 the kyb free pistons are vented is it true? If it is the pistons should drain the oil automatically
Ichnusa Added a reply to Kyb free pistons
5/2/2022 11:52am There is an oring in the top of the free piston how can the oil drain out?
Ichnusa Added a reply to Kyb free pistons
5/2/2022 5:40am How can i drain it out?
Ichnusa Started a new thread Kyb free pistons
5/2/2022 4:46am Hello, I have a 22 yz250f and i played with oil level but i have a doubt can oil be trapped in free piston chamber?
This forum thread has 8 replies.
Ichnusa Added a reply to The influence of rebound clicker in compression
3/4/2022 6:47am Yes it's maybe because in the compression adjuster flows only the oil volume moved by the shaft instead trought the rebound flows oil at all piston movements so a major oil volume at equal of stroke that's right?
willbilly Liked a reply to forum topic The influence of rebound clicker in compression
3/4/2022 1:17am
It’s the low speed bleed bypass. So it would affect low shaft speed regardless of the amount of movement.
This forum topic has 5 replies.
Ichnusa Started a new thread The influence of rebound clicker in compression
3/3/2022 8:56am Hello everyone, we all know that rebound clickers influences compression too but how much? More in suspension's long strokes or in short ones? I would say in what conditions that influence feels more? on big bumps/rollers or in square edge? Or maybe in load transfers?
This forum thread has 5 replies.
Ichnusa Added a reply to Help! Yz250f twitchy front end
2/23/2022 7:55am I've already tried to turn in 1/4 the hsc and it solve the shock diving but gives a sinkbug feel, front end heavy and twichness so I'm back to 1.5 HSC and close 4 clicks in compression but it don't do the trick... so I'm whatching for the rebound that like wrc777 said affects even the compression and it's the...
Ichnusa Added a reply to Help! Yz250f twitchy front end
2/23/2022 4:36am I've tryed to drop the sag but it made not much effect so I've set back the hsc to 1.5 and it had calm down the front but the bike but, under acceleration, it's back to squat too easily, in exit of corners the rear end goes up and down, moves side to side and in big bumps blows thru...
Ichnusa Added a reply to Help! Yz250f twitchy front end
2/18/2022 10:02am I mount it back because I'm not so tall I'm 168cm but I will try it a little more in front
Ichnusa Added a reply to Help! Yz250f twitchy front end
2/18/2022 9:13am "Having your bars in the front position is best. If you have them in the closest to rider position it will really mess with things" Really? Why? I have it in the closest rider position
Ichnusa Added a reply to Help! Yz250f twitchy front end
2/17/2022 12:34pm I did search in q-springs calculator and it reccommended 4.4nm fork springs