Recent Activity
All
Husky82 Started a new thread Fc 450 Cam and rocker arm wear?
7/18/2022 2:33pm The bike began making the infamous ticking sound which sounded like the cam chain tensioner. I took the bike apart checked my tensioner and replaced it with the tokyo mods manual one. I also checked my valve clearance which was out of spec. I got them all in spec and of course did all of this while at top dead...
This forum thread has 18 replies.
Husky82 Added a reply to Fc 450 Cam and rocker arm wear?
3/15/2020 7:32pm Looks like more bad news, no idea if this needs to be repaired or if I can get by with it? 
More »
Husky82 Added a reply to Fc 450 Cam and rocker arm wear?
3/14/2020 8:40pm Paw Paw, What would cause it to be starving for oil, what do I look for?
Husky82 Added a reply to Fc 450 Cam and rocker arm wear?
3/14/2020 8:22pm Dynodan, the bike has 65 hours top end was done at 60. My intake valves were very tight when I originally checked them which may explain why this could happen. I also noticed the intake rocker arm shaft has an extra hole in the middle where I am assuming oil lubricates the system. I did not notice this until after...
Husky82 Added a reply to Fc 450 Cam and rocker arm wear?
3/14/2020 3:28pm
Husky82 Started a new thread 2003 rm 125 airbox/boot help
6/9/2019 12:51pm Right where the boot and Airbox meet there is a metal cage where the filter connects. two spots opposite each other there is a gap. Is this normal? I’m getting dirt into the boot, and I have a new filter and good filter seal so I can’t figure out where the dirt is coming from other than possibly those gaps
This forum thread has 1 reply.
Kennyfreemoney Liked a reply to forum topic Ktm lever help
4/11/2019 6:26am
Tusk! Can't beat $8
This forum topic has 26 replies.
Husky82 Added a reply to spark plug gap is closing?
8/8/2018 6:03am Also I was told to look at the timing and that it could cause this and it was slightly off so I got that centered back up and will see if this fixes my problem as well
Husky82 Added a reply to spark plug gap is closing?
8/8/2018 6:01am I will have to check out the flat/dome piston and see if i'm running the wrong one. As for the spark plug i have run a br9eg plug in previous rm 125s and never had a problem. I guess if the piston is right i will try the better plug, but i'd hate to bust up a 25 dollar sparkplug...
Husky82 Started a new thread spark plug gap is closing?
8/7/2018 8:54am 2003 rm 125, the spark plug arm is bending up and completely closing the gap after about 3 laps (6 minutes), happened twice in a row after a long wide open straight. replace the plug and it runs perfect until this happens again. Previous to this the whole engine was rebuilt with new everything except transmission. Cylinder was replated and...
This forum thread has 12 replies.
Husky82 Added a reply to spark plug gap is closing?
8/7/2018 8:37am That was my initial thought, but the arm isn't showing damage its just evenly bent upward.
Husky82 Started a new thread 2003 rm 134 build
7/25/2018 8:29am Picked up two rm 125s that were corroding away in a barn. 1 was kind of a rolling chassis and the other was a frame and front forks, all the rest of the parts were 2 motors half way torn apart and parts in boxes. 
This forum thread has 3 replies.
Husky82 Added a reply to 2003 rm 134 build
7/25/2018 8:28am Both the carburetors I got with the bike needed a new slide and in the process of finding one i ended up getting a good deal on a new whole carb that they set up for my plans with the bike 
Husky82 Added a reply to 2003 rm 134 build
7/25/2018 8:19am had the hubs turned down and laced the wheels up 
Tore the engine down and replaced every bearing, went through the transmission that was missing washers, replaced the crank and had the cylinder re-plated and bored out to a 134. Both the valves were broken so I bought new ones(TOO expensive). Also had the head fixed...
Tore the engine down and replaced every bearing, went through the transmission that was missing washers, replaced the crank and had the cylinder re-plated and bored out to a 134. Both the valves were broken so I bought new ones(TOO expensive). Also had the head fixed...
Husky82 Added a reply to 2003 rm 134 build
7/22/2018 6:49pm decided to use the yellow frame because it was an 03 and so was the more usable engine block. 
The tab was off so I cut it off and welded it back properly. Both the foot pegs pins were bent and impossible to get out so I had to cut the pegs off the frame. My...
The tab was off so I cut it off and welded it back properly. Both the foot pegs pins were bent and impossible to get out so I had to cut the pegs off the frame. My...
Husky82 Started a new thread ISO rm 125 kickstarter
7/16/2018 6:23pm Need a kickstart lever for a 2003 rm 125
This forum thread has 0 replies.
Husky82 Added a reply to 2008 RM125 bike build
6/29/2018 11:38am turned out awesome, what did you use on the frame/covers/swingarm? Almost looks rhino lined.
Husky82 Added a comment about bike check 2003 Suzuki RM125
6/21/2018 3:48pm
Where did you find the graphics?
This bike check has 8 comments.
Husky82 Started a new thread ISO 2003 RM 125 water pump gear/shaft
6/21/2018 8:30am If anyone has one for sale please send me a PM.
This forum thread has 0 replies.
Husky82 Started a new thread Suzuki parts garage sale
6/17/2018 6:39pm Clearing the garage of RM and RMZ parts, make me an offer. RM 125 parts 2 sets of front forks RH engine case stock exhaust stock reed valves 2003 cylinder (needs work) cylinder head (needs work) 2003 power valve power valve cover triple clamps 2001 frame front hub 1 excel front rim 1 oem front rim 1 rear rim complete...
This forum thread has 1 reply.