FMF factory fatty raw pipe maintenance

mxaniac
Posts
697
Joined
9/9/2019
Location
Airway Heights, WA, USA
5/17/2026 8:59am

I've tried about everything mentioned, when it comes to really heavy rust nothing beats oxalic acid. It is often sold as wood bleach. I would only use it on something covered in rust, as end result isn't great visually.

captmoto
Posts
5929
Joined
4/22/2009
Location
Rancho Cucamonga, CA, USA
5/17/2026 9:18am
GrapeApe wrote:
I always used Lime-A-Way when my two stroke pipes started to get stained or rusty. I assume it is similar if not the same as CLR...

I always used Lime-A-Way when my two stroke pipes started to get stained or rusty. I assume it is similar if not the same as CLR, it worked really well. WD40 for maintenance after every wash.

They're basically the same. I used Fluid Film on my YZ465 3 years ago and while it has say on my garage all this time or still looks really good. FWIW Fluid Film stinks so it must be good.

TheMilkman
Posts
1505
Joined
7/6/2022
Location
Plano, TX, USA
5/17/2026 1:19pm
eeazye wrote:
Reporting back after trying Milkman’s suggestion about the cerakote wipes. Great success! Ultimately I took a bit of advice from several folks on here to get...

Reporting back after trying Milkman’s suggestion about the cerakote wipes. Great success! Ultimately I took a bit of advice from several folks on here to get it done. I tried CLR straight first, and it worked well, but the rust was too heavy, and was left with rust in the micro-pitting. I really wanted to avoid going at it with heavy abrasives to avoid scratches I’d have to deal with later.

So went up a  level to muriatic acid. That was the key. It stripped the rust and the bluing around the welds. Left a dull grey finish on the entire pipe. There were a few streaks I had go over where the acid sat longer than other areas before rinsing it off. You’re on the clock when you’re using this stuff!

Then I went over the welds with a MAPP torch to “blue” the welds. Wiped it down with wax and grease remover, and then hit it with the cerakote wipe. One wipe was more than enough to cover the whole pipe. It does leave a gloss finish, but it’s not over the top. Paid $16 usd for a box of 10 wipes from the rainforest company. 

I’ve got the first ride on it done with heavy mud sitting for a day before I could wash the bike. The mud/grass basically just rinsed right off, pipe still looks great! I went to oil the pipe after washing out of habit, and stopped myself halfway through. I wiped the oil off, hopefully that doesn’t disturb the coating. 

Thanks to everyone that gave tips on this thread!

Glad it worked out for you. I was skeptical before trying it and have been really happy with it. I’d like to find a cerakote clear option that has a little higher temperature rating so that I don’t even have to touch up the initial part of the exhaust. But for now I’m happy with what I’ve got since it’s the lowest maintenance option I’ve found yet.

1
mwp317
Posts
6
Joined
9/23/2024
Location
Denver, CO, USA
5/31/2026 6:52am

Just applied Cerakote wipes to the factory fatty on my yz125, looks sweet, i neglected this pipe for a while so tried to clean her up. Next time I have to take the bike apart I’ll do a deeper clean. 


Going to ride today I’ll share pics of how it looks after 

IMG 3797 2.jpeg?VersionId=YMBA oCFc1xaYSyq3GRK.c7llJ1tc

 

IMG 3796 3IMG 3795 4.jpeg?VersionId=gV93JDzmT4cKiNOwiw5jbt99gFKNMW

The Shop

eeazye
Posts
335
Joined
10/22/2009
Location
Akron, OH, USA
5/31/2026 9:40am
mwp317 wrote:
Just applied Cerakote wipes to the factory fatty on my yz125, looks sweet, i neglected this pipe for a while so tried to clean her up...

Just applied Cerakote wipes to the factory fatty on my yz125, looks sweet, i neglected this pipe for a while so tried to clean her up. Next time I have to take the bike apart I’ll do a deeper clean. 


Going to ride today I’ll share pics of how it looks after 

IMG 3797 2.jpeg?VersionId=YMBA oCFc1xaYSyq3GRK.c7llJ1tc

 

IMG 3796 3IMG 3795 4.jpeg?VersionId=gV93JDzmT4cKiNOwiw5jbt99gFKNMW

I found that mine wound up flash rusting again in small areas that rocks/debris spraying from the front tire hit it. However, I just hit the affected area with 0000 steel wool, degreased it, and reapplied the cerakote. Much more reasonable and manageable than what I had going on with just scotch brite and light oil. 

Your pipe looks great!

Post a reply to: FMF factory fatty raw pipe maintenance

The Latest