KTM 350 piston kit question

Dirtfighter
Posts
233
Joined
7/25/2020
Location
Naples, FL, USA

Placing an order for a new top end on my 22 350. There are two options but there is no description on the difference only  I , II option. I assume it’s piston size. Do I need to look at my original piston for markings? Was hoping to order everything before I open her up.  Also what’s your opinion on valve spring kit at 65 hrs? Was gonna get the collets at least but considering the whole kit less valves, of course timing chain too.

|
cwtoyota
Posts
2424
Joined
3/11/2013
Location
Tacoma, WA, USA
8/31/2023 8:05pm
Placing an order for a new top end on my 22 350. There are two options but there is no description on the difference only  I...

Placing an order for a new top end on my 22 350. There are two options but there is no description on the difference only  I , II option. I assume it’s piston size. Do I need to look at my original piston for markings? Was hoping to order everything before I open her up.  Also what’s your opinion on valve spring kit at 65 hrs? Was gonna get the collets at least but considering the whole kit less valves, of course timing chain too.

I don't know for sure, but I'll bet there's a note about it in the factory service manual.

VetStuff
Posts
23
Joined
1/25/2023
Location
Round Rock, TX, USA
8/31/2023 9:41pm

Are you hard on the engine?

I’m a vet moto rider on a tuned up 350 and have measured valves a couple times over 90 hours with no change and piston top looked fine at 50 hours on a bore scope. i decided to skip the top end at 50 and i’m at 90 hours on top and bottom. i do oil every 5 hours or less though as preventative.

at 65 i didnt even think about head issues…

 

Dirtfighter
Posts
233
Joined
7/25/2020
Location
Naples, FL, USA
9/1/2023 5:53am

I wouldn’t say I’m hard but I ride it the way a 350 should be ridden and I’m in Florida so it’s hot and a lot of my riding is on the sandy side. 
 I’ve been on 450’s since 2008 always did top ends around 90hrs. They never looked worn especially since switching to the Austrian brand in 2019. I mostly did them because I sell them around 100 and like them to be fresh when listing. 
This is my first experience with a 350 and have decided to keep this one for another year. A wrist injury sidelined me for several months so my whole annual bike program was thrown off. This bike should have been sold already . I’m actually gonna try and source another new or practically new 22 and stick with the old platform. As far as the valve parts are concerned, Chad from XPR is who recommended an entire valve and spring replacement. I figured at least collets since they’re heap and hold all the force.

sandman768
Posts
8304
Joined
3/21/2014
Location
Saratoga Springs, NY, USA
9/1/2023 5:53am
VetStuff wrote:
Are you hard on the engine? I’m a vet moto rider on a tuned up 350 and have measured valves a couple times over 90 hours...

Are you hard on the engine?

I’m a vet moto rider on a tuned up 350 and have measured valves a couple times over 90 hours with no change and piston top looked fine at 50 hours on a bore scope. i decided to skip the top end at 50 and i’m at 90 hours on top and bottom. i do oil every 5 hours or less though as preventative.

at 65 i didnt even think about head issues…

 

I was going to state the same…. Unless you have a specific reason..IE …sucked dirt…metal shavings in oil… or you are a Pro or serious A rider, anything under 100 hrs is a waste…at 100hrs I would use the slightly large OD piston .. piston kit #2. I do remember on my 450sfx looking for number or letter on back side of cylinder.. I tried looking on my 22 350sfx last nite, could not see anything definitive..

The Shop

FGR01
Posts
6176
Joined
10/1/2006
Location
USA
9/1/2023 8:00am

The cylinder is marked on the front side, beneath where the tensioner is.  If you get down on your knees and screw around with the light, zoom, and camera on your cell phone you'll be able to get a picture of it and read it.  The piston is marked as shown below.
image-20230901075914-1

image-20230901080029-2

3
Dirtfighter
Posts
233
Joined
7/25/2020
Location
Naples, FL, USA
9/1/2023 2:18pm
FGR01 wrote:
The cylinder is marked on the front side, beneath where the tensioner is.  If you get down on your knees and screw around with the light...

The cylinder is marked on the front side, beneath where the tensioner is.  If you get down on your knees and screw around with the light, zoom, and camera on your cell phone you'll be able to get a picture of it and read it.  The piston is marked as shown below.
image-20230901075914-1

image-20230901080029-2

Perfect thank you!

1

Post a reply to: KTM 350 piston kit question

The Latest