Need Help Identifying Part

chrisr22
Profile picture for user chrisr22
Posts
56
Joined
2/5/2015
Location
Mountain Home, AR, USA
chrisr22
Edited Date/Time 3/5/2015 2:14pm
Working on a major rebuild of an 08 kx250f and I have a spare part I cant identify through microfiche.
It is marked with HBT2047M. Google shows no results. Anybody seen one of these and know where it belongs?

Oh and by the way I work in an auto repair shop so it may or may not belong to the bike Woohoo
|
JBernard_401
Profile picture for user JBernard_401
Posts
1317
Joined
10/29/2013
Location
Boulder, CO, USA
JBernard_401 3/3/2015 8:27am
3/3/2015 8:27am
kickstarter output shaft seal?
slipdog
Profile picture for user slipdog
Posts
10054
Joined
7/25/2009
Location
Nor Cal, CA, USA
slipdog 3/3/2015 8:31am
3/3/2015 8:31am
Closest thing it resembles to me is the seal for the valve cover bolt. Kind of, but not really... #92055-1352
chrisr22
Profile picture for user chrisr22
Posts
56
Joined
2/5/2015
Location
Mountain Home, AR, USA
chrisr22 3/3/2015 8:43am
3/3/2015 8:43am Edited Date/Time 3/3/2015 8:45am
Checked both of those... I am really starting to think it doesn't belong on this bike. If it is a part of the bike it is from the engine. This appeared after replacing cam chain, valves, valve springs and piston. Had the outer clutch cover and ignition cover off of course.
rallendude
Profile picture for user rallendude
Posts
2203
Joined
8/17/2006
Location
Adger, AL, USA
rallendude 3/3/2015 2:27pm
3/3/2015 2:27pm
How about a couple more photos less blurry, straight from front and also from back too?

The Shop

See All »
chrisr22
Profile picture for user chrisr22
Posts
56
Joined
2/5/2015
Location
Mountain Home, AR, USA
chrisr22 3/3/2015 2:34pm
3/3/2015 2:34pm
Best I can get with my phone... I have gone over everything twice. Appreciate the help!





Honda11
Profile picture for user Honda11
Posts
268
Joined
1/10/2015
Location
Inside, KY, USA
Honda11 3/3/2015 2:44pm
3/3/2015 2:44pm
Its not the seal that goes where the clutch arm goes into the engine is it? Kinda looks like the seal I had to replace on my 09 kx450f, but its been a couple years ago.
chrisr22
Profile picture for user chrisr22
Posts
56
Joined
2/5/2015
Location
Mountain Home, AR, USA
chrisr22 3/3/2015 2:48pm
3/3/2015 2:48pm
Honda11, haven't had the clutch arm out. Didn't split cases on this one.
Honda11
Profile picture for user Honda11
Posts
268
Joined
1/10/2015
Location
Inside, KY, USA
Honda11 3/3/2015 2:50pm
3/3/2015 2:50pm
Ok it must be different, I didn't have to split cases to remove mine, there was just a clip that held the arm into the engine, and below that was the seal I replaced.
Honda11
Profile picture for user Honda11
Posts
268
Joined
1/10/2015
Location
Inside, KY, USA
Honda11 3/3/2015 2:51pm
3/3/2015 2:51pm
It also looks like a rubber that would go below a radiator peg on newer model cars (older models had bigger rubbers of the same design).
motofab36
Profile picture for user motofab36
Posts
1429
Joined
4/1/2008
Location
Cowden, IL, USA
motofab36 3/3/2015 5:20pm
3/3/2015 5:20pm
Its not from the bike
slipdog
Profile picture for user slipdog
Posts
10054
Joined
7/25/2009
Location
Nor Cal, CA, USA
slipdog 3/3/2015 5:39pm
3/3/2015 5:39pm
motofab36 wrote:
Its not from the bike
Nailed it!
chrisr22
Profile picture for user chrisr22
Posts
56
Joined
2/5/2015
Location
Mountain Home, AR, USA
chrisr22 3/3/2015 5:45pm
3/3/2015 5:45pm
I had pretty much convinced myself through the day today that this had to be a car part. Having y'all agree seals the deal! Thanks a ton!

And if it is for the bike I will find out when she starts leaking Cool
rallendude
Profile picture for user rallendude
Posts
2203
Joined
8/17/2006
Location
Adger, AL, USA
rallendude 3/5/2015 11:49am
3/5/2015 11:49am
It looks a little like one of the water pump seals from a newer Honda but the microfiche seems to show a normal two seal set up on the 2008 KX250f.
mxtech1
Profile picture for user mxtech1
Posts
1968
Joined
7/21/2011
Location
Galesburg, IL, USA
mxtech1 3/5/2015 2:14pm
3/5/2015 2:14pm
chrisr22 wrote:
I had pretty much convinced myself through the day today that this had to be a car part. Having y'all agree seals the deal! Thanks a...
I had pretty much convinced myself through the day today that this had to be a car part. Having y'all agree seals the deal! Thanks a ton!

And if it is for the bike I will find out when she starts leaking Cool
Lol....nothing like that feeling of having a mystery part laying around!

Post a reply to: Need Help Identifying Part