Top end bog 250 2stroke

motokawi818
Posts
836
Joined
4/7/2008
Location
Kennewick, WA, USA
Edited Date/Time 9/2/2012 9:49pm
I have a 2004 kx250 and whenever I start getting into my moto like 4-5 laps in my big will bog super hard up top. To the point where I can't give it gas past quarter throttle without it fully bogging. Do any of you know what would cause this and how to fix it? I'm at the track now so that's why I posted it in the main forum.
|
onthepipe
Posts
285
Joined
8/26/2012
Location
NL
9/1/2012 11:00am
Way rich, or sparkplug/electrical issue.
tapkawiman
Posts
170
Joined
4/1/2008
Location
Neosho, MO, USA
9/1/2012 11:03am
Check the gas cap vents, make sure they are letting air into the gas tank.
motokawi818
Posts
836
Joined
4/7/2008
Location
Kennewick, WA, USA
9/1/2012 11:06am
I'll try the gas cap thing and see if it helps. Also it's pretty dark around the end of my silencer. Does that mean its rich? Thanks guys
NP301
Posts
2669
Joined
1/19/2010
Location
Keene, NH, USA
9/1/2012 11:06am
Could be..Reeds, ignition, timing, gas hose vent, and It could also be too rich.

The Shop

motokawi818
Posts
836
Joined
4/7/2008
Location
Kennewick, WA, USA
9/1/2012 11:29am
I jus tried the gas cap thing and the same thing happened. Around 5 hard laps in the top end bog starts back up. I noticed a small leak in the bottom of my carb this time though.
CR250Rider
Posts
6706
Joined
4/1/2008
Location
Moses Lake, WA, USA
9/1/2012 11:44am
I'd guess it's flooded by a faulty float needle / seat

could be stator loses some current when it heats up, too.


Is it smokey when it's "bogging"
you have tried a few other spark plugs, right?
motokawi818
Posts
836
Joined
4/7/2008
Location
Kennewick, WA, USA
9/1/2012 11:44am
Thanks a lot!! My dad should be able to do it he's been my mechanic my whole life Tongue haha but definitely when I get home me and him will tear it apart.
reded
Posts
3682
Joined
3/26/2011
Location
USA
9/1/2012 12:42pm
Coil.
partialperson
Posts
409
Joined
11/6/2006
Location
Murphysboro, IL, USA
9/1/2012 7:09pm
IS THE END OF THE SILENCER BLACK AND OILY TO THE TOUCH? Sorry, caps lock. Does it smoke more than it used to when you first start it? Right side crank seal sucking tranny fluid.
lilbulld
Posts
509
Joined
1/6/2010
Location
USA
9/1/2012 7:50pm
float and/or needle
FGR01
Posts
6181
Joined
10/1/2006
Location
USA
9/1/2012 9:29pm
Possible air leak from a failure to seal around the reed block/intake manifold. Many times these appear when the bike get good and hot and things expand. Might explain the gas under your carb.
Matt Fisher
Posts
3945
Joined
4/1/2008
Location
Visalia, CA, USA
9/1/2012 10:20pm
While the carb is off take 5 more minutes to pull the reed block and look for a chipped reed(s).
motokawi818
Posts
836
Joined
4/7/2008
Location
Kennewick, WA, USA
9/1/2012 10:22pm
I did notice more smoke right when I started my bike. I did a moto at the end of the day when I rarely went past half throttle and it rarely did the bog. The seal thing does make sense because the problem is when the bikes real hot. I wasn't able to tear into the carb today but tomorrow I'm going to wash it then tear it apart. Thanks for all the input guys it really is helping.
SEEMEFIRST
Posts
14284
Joined
8/21/2006
Location
Arlington, TX, USA
9/2/2012 2:45am Edited Date/Time 9/2/2012 2:48am
I did notice more smoke right when I started my bike. I did a moto at the end of the day when I rarely went past...
I did notice more smoke right when I started my bike. I did a moto at the end of the day when I rarely went past half throttle and it rarely did the bog. The seal thing does make sense because the problem is when the bikes real hot. I wasn't able to tear into the carb today but tomorrow I'm going to wash it then tear it apart. Thanks for all the input guys it really is helping.
You can spray WD-40 around the reed block and manifold while it's idleing, and if it revs when the spray hits it, you have a leak there.
Not a sure fire method of detecting leaks, but if you have a good one, it'll show it.

The crank seal sounds viable as well, not as easy to detect. This is why some were asking about plug checks. If you check the plug right after it does the bog, it might tell you a lot.
JW381
Posts
10638
Joined
7/21/2009
Location
Harrisburg, OR, USA
9/2/2012 5:37am
Just out of my own curiousity - how difficult and expensive is it to change a right side crank seal?
partialperson
Posts
409
Joined
11/6/2006
Location
Murphysboro, IL, USA
9/2/2012 7:26am Edited Date/Time 9/2/2012 7:29am
Most right side crank seals are pretty easy. Remove clutch hub, drive gear that runs clutch hub on crankshaft will slide off crank and seal is behind it. Some are that easy, I have only done a few. Seal, clutch side gasket probably less than $50
Matt Fisher
Posts
3945
Joined
4/1/2008
Location
Visalia, CA, USA
9/2/2012 9:24am
Unless that generation KX250 is different, you need to split the cases to change the crank seals on a Kawasaki.

Still, I'd lean toward reeds, as I had a similar bogging issue with my son's RM85 about 3 months ago. No spooge in the tailpipe though, he's jetted well and rides it with the throttle pinned.
JW381
Posts
10638
Joined
7/21/2009
Location
Harrisburg, OR, USA
9/2/2012 9:37am
I have an 04 CR 250 and I have a slight inkling that the right side seal could be bad. I've been messing with the jetting since I bought it, so it was extremely rich at first. So I'm not fully decided yet on if the excess spooge is from the jetting or from a crank seal.

Anyone know the procedure for that generation CR?

Thanks mechanic pros.
JW381
Posts
10638
Joined
7/21/2009
Location
Harrisburg, OR, USA
9/2/2012 9:38am
BTW, sorry to hijack the thread, I just found it to be relevant. Hopefully the OP gets his bog figured out.
Matt Fisher
Posts
3945
Joined
4/1/2008
Location
Visalia, CA, USA
9/2/2012 3:12pm
JW381 wrote:
I have an 04 CR 250 and I have a slight inkling that the right side seal could be bad. I've been messing with the jetting...
I have an 04 CR 250 and I have a slight inkling that the right side seal could be bad. I've been messing with the jetting since I bought it, so it was extremely rich at first. So I'm not fully decided yet on if the excess spooge is from the jetting or from a crank seal.

Anyone know the procedure for that generation CR?

Thanks mechanic pros.
That bike has 2 main issues- squish is to large, making the combustion process inefficient, and the TMX carb is very sensitive to atmospheric conditions.

Do a search here and on ThumperTalk, there are multiply threads in that bike.
JW381
Posts
10638
Joined
7/21/2009
Location
Harrisburg, OR, USA
9/2/2012 8:36pm
Yeah I have for sure. I'm gonna buy an air striker here soon. Still getting a fair amount of black oil out the silencer tho, it makes me uneasy.
motokawi818
Posts
836
Joined
4/7/2008
Location
Kennewick, WA, USA
9/2/2012 8:42pm
Yeah I ride it pinned it's not a splooge issue as its not wet. It just has a darker look than I've noticed before. I stalled the tear down because my dads out of town and I don't want to screw it up Tongue
SEEMEFIRST
Posts
14284
Joined
8/21/2006
Location
Arlington, TX, USA
9/2/2012 9:49pm
Yeah I ride it pinned it's not a splooge issue as its not wet. It just has a darker look than I've noticed before. I stalled...
Yeah I ride it pinned it's not a splooge issue as its not wet. It just has a darker look than I've noticed before. I stalled the tear down because my dads out of town and I don't want to screw it up Tongue
Excellent idea.

Post a reply to: Top end bog 250 2stroke

The Latest