Cr250 Project Pics

MxSkillz
Posts
333
Joined
12/13/2011
Location
Bermuda, BM
12/14/2011 7:43am Edited Date/Time 12/14/2011 7:47am
newmann wrote:
While I can't get too amped up over a polished frame, I do admire the time and effort to achieve a polished finish. I also admire...
While I can't get too amped up over a polished frame, I do admire the time and effort to achieve a polished finish. I also admire the attention to detail throughout the entire project and that is coming from someone who has done a project or two! Wink

But really, I have to ask what's a wealthy chick pulling stud like yourself doing hanging out in a place like this???


Lol.. haha Nice! See i try to keep myself as humble az possible and not let my chick pulling good looks, fame, talent and fortune deter me from mixin it up with the common folk.. lol.. I have to check that movie.. didnt even know it was around.
M-M
Posts
2138
Joined
11/20/2008
Location
GB
12/14/2011 7:47am
Good job buddy. Bike looks sweet.
MxSkillz
Posts
333
Joined
12/13/2011
Location
Bermuda, BM
12/14/2011 7:55am
parttime66 wrote:
Bike looks great. I want to help my nephew polish his frame this winter. Any tips on how you got the finish so nice. Did you...
Bike looks great. I want to help my nephew polish his frame this winter. Any tips on how you got the finish so nice. Did you sand by hand 400,800,1200,2000 then buff?
Yea you got it prettyy much.. i went 400,600,800,1000,1200,1500,2000.. then polished with mothers poilsh.. I did that for 3/4 of the bike and came tothe conclusion i was the biggest moron for not buying this kit to complete the last 1/4 before i started.. Dude.. its cheap, it works and lasts longer.. The different compuonds break it down perfectly.. black cuts the serious 1st layer off.. the brown is a little finer.. and the white is the finest and the last step of the process.. after buying this kit i actually redid the whole bike.. do urself a favor and buy it.. http://www.eastwood.com/aluminum-polishing-kit-13-pc-set.html
MxSkillz
Posts
333
Joined
12/13/2011
Location
Bermuda, BM
12/14/2011 7:58am
M-M wrote:
Good job buddy. Bike looks sweet.
Thanks man.. but that womans ass in ur pic looks better, i will trade you..

The Shop

Top End
Posts
474
Joined
2/28/2010
Location
NOR-CAL, CA, USA
12/14/2011 8:00am
Very nice attention to detail. I like how you used the front fender as a stand when polishing on the table. I picked up a 03 and am rebuilding it. I hope it turns out half as good as yours.
captmoto
Posts
5929
Joined
4/22/2009
Location
Rancho Cucamonga, CA, USA
12/14/2011 8:12am
Who in hell lets a bike get that far gone????
Hando
Posts
1571
Joined
11/13/2011
Location
USA
12/14/2011 8:15am
the best part about this bike is the bead blasted engine cases

#FACTORY!!
jeffro503
Posts
27650
Joined
7/22/2007
Location
St Helens, OR, USA
12/14/2011 8:56am Edited Date/Time 12/14/2011 8:59am
HOLY $#@*! Dude.....awesome job on the restore man! That Honda is looks beautiful man! A lot of time , money and effort......and worth every penny!

OH...and by the way.....that second pic down , with the bike frame sitting in front of the car. It looks like an optical illusion......it looks like it's floating there at first glance. I stared at that pic for a couple minutes....it still looks weird.
layinbody31
Posts
530
Joined
11/2/2011
Location
Cedar Lake, IN, USA
12/14/2011 9:16am
I have to fully agree with everyone here... this thing looks amazing!

I plan on picking up an '01 CR250 in the near future and doing an '02-'07 plastics conversion on it. I have one question for you though... Where did you get the '11-12 Factory graphics?? I was debating what kind of style/theme to build it with and I think I've found it Smile
CR250Rider
Posts
6706
Joined
4/1/2008
Location
Moses Lake, WA, USA
12/14/2011 9:18am Edited Date/Time 12/14/2011 9:37am
Since this is a CR250 thread I have a question.

On another website they were talking about the RC motor being weak and adding to the soft powerband, BUT the factory mechanics for team honda had "solved" the problem.

anyone one know what they did?
insert a bigger motor from somewhere?
up the voltage to the exiting motor?


any factory wrenches out there know anything?
dirthead1
Posts
1440
Joined
4/1/2008
Location
Southern, CA, USA
12/14/2011 9:26am
Rad living room build.
bg22
Posts
422
Joined
9/18/2009
Location
USA
12/14/2011 9:40am
Excellent job! I'd love to go over my '02 like that. Mine is starting to look dated and needs a refresh.
MxSkillz
Posts
333
Joined
12/13/2011
Location
Bermuda, BM
12/14/2011 10:06am
Thanks alot fellaz! your makin all the work i put in worth it!
MxSkillz
Posts
333
Joined
12/13/2011
Location
Bermuda, BM
12/14/2011 10:11am Edited Date/Time 12/14/2011 10:13am
I have to fully agree with everyone here... this thing looks amazing! I plan on picking up an '01 CR250 in the near future and doing...
I have to fully agree with everyone here... this thing looks amazing!

I plan on picking up an '01 CR250 in the near future and doing an '02-'07 plastics conversion on it. I have one question for you though... Where did you get the '11-12 Factory graphics?? I was debating what kind of style/theme to build it with and I think I've found it Smile
Yea.. i was lookin for ages for that "factory clean look" here you go mate.. order away. They just made available the new 2012 factory muscle milk graphic kit as well.. but i prefer these ones better..http://throttlejockey.com/product/x_yQTN93QWawZiMzEY2lkPT/New%20Items

Get the seat cover as well.. sets it off perfect cause they color match the red with the graphics
Hando
Posts
1571
Joined
11/13/2011
Location
USA
12/14/2011 10:14am
CR250Rider wrote:
Since this is a CR250 thread I have a question. On another website they were talking about the RC motor being weak and adding to the...
Since this is a CR250 thread I have a question.

On another website they were talking about the RC motor being weak and adding to the soft powerband, BUT the factory mechanics for team honda had "solved" the problem.

anyone one know what they did?
insert a bigger motor from somewhere?
up the voltage to the exiting motor?


any factory wrenches out there know anything?
I read in MXA that Honda spent close to $100,000 to get the motor to RC's liking.

The motor isn't that bad as everyone makes it out to be, it just doesn't have the low-end power of the other 250 2-strokes..which are pretty much all YZ clones except for the 250SX.
MxSkillz
Posts
333
Joined
12/13/2011
Location
Bermuda, BM
12/14/2011 10:15am
CR250Rider wrote:
Since this is a CR250 thread I have a question. On another website they were talking about the RC motor being weak and adding to the...
Since this is a CR250 thread I have a question.

On another website they were talking about the RC motor being weak and adding to the soft powerband, BUT the factory mechanics for team honda had "solved" the problem.

anyone one know what they did?
insert a bigger motor from somewhere?
up the voltage to the exiting motor?


any factory wrenches out there know anything?
Yea i quoted ur questionin the othe forum.. hope that helps
MxSkillz
Posts
333
Joined
12/13/2011
Location
Bermuda, BM
12/14/2011 10:18am
CR250Rider wrote:
Since this is a CR250 thread I have a question. On another website they were talking about the RC motor being weak and adding to the...
Since this is a CR250 thread I have a question.

On another website they were talking about the RC motor being weak and adding to the soft powerband, BUT the factory mechanics for team honda had "solved" the problem.

anyone one know what they did?
insert a bigger motor from somewhere?
up the voltage to the exiting motor?


any factory wrenches out there know anything?
Hando wrote:
I read in MXA that Honda spent close to $100,000 to get the motor to RC's liking. The motor isn't that bad as everyone makes it...
I read in MXA that Honda spent close to $100,000 to get the motor to RC's liking.

The motor isn't that bad as everyone makes it out to be, it just doesn't have the low-end power of the other 250 2-strokes..which are pretty much all YZ clones except for the 250SX.
Exactly dude..In 05 they rivised the tps (throttle positioning sensor) which comes from the carb.. sends a signal to the cdi which sends a signal to the servo motor which opens the rc valve at a certain rpm range.. These bikes are underrated.. This technology was adapted from the honda road race team and with a few more tweaks could have been perfect..What it does is provide better traction at the right time. The reason why they feel mellow to everyone is because this system like i said is set up for the correct timing which produces the best traction at the right time..

Coming out of a corner.. everybody wants the most power.. but the more power, the more wheelspin= no traction= spinning out or slower lap times. What they tried to do was brilliant, but not quite right yet.. i wish they would have put more r&d into this cause it was going in the right direction.. But these years can become very potent with a few tweaks to the motor and a few mods for sure.. i have a 05.. and have more power than i will ever need and is a blas to ride.
newmann
Posts
24437
Joined
4/1/2008
Location
USA
12/14/2011 10:21am
I have to fully agree with everyone here... this thing looks amazing! I plan on picking up an '01 CR250 in the near future and doing...
I have to fully agree with everyone here... this thing looks amazing!

I plan on picking up an '01 CR250 in the near future and doing an '02-'07 plastics conversion on it. I have one question for you though... Where did you get the '11-12 Factory graphics?? I was debating what kind of style/theme to build it with and I think I've found it Smile
MxSkillz wrote:
Yea.. i was lookin for ages for that "factory clean look" here you go mate.. order away. They just made available the new 2012 factory muscle...
Yea.. i was lookin for ages for that "factory clean look" here you go mate.. order away. They just made available the new 2012 factory muscle milk graphic kit as well.. but i prefer these ones better..http://throttlejockey.com/product/x_yQTN93QWawZiMzEY2lkPT/New%20Items

Get the seat cover as well.. sets it off perfect cause they color match the red with the graphics
Let me just throw in there that Throttle Jockey refused to hit the print button for me when I needed a set of Woody graphics for my 2002 CR250 "clean up project". They were still for sale on the website, just out of stock. No reason given as to why they wouldn't print me a set. Thankfully the guys over at 180 Decals hooked me up and the price was very good especially with the artwork involved for a set of one off graphics.

Hando
Posts
1571
Joined
11/13/2011
Location
USA
12/14/2011 10:32am
CR250Rider wrote:
Since this is a CR250 thread I have a question. On another website they were talking about the RC motor being weak and adding to the...
Since this is a CR250 thread I have a question.

On another website they were talking about the RC motor being weak and adding to the soft powerband, BUT the factory mechanics for team honda had "solved" the problem.

anyone one know what they did?
insert a bigger motor from somewhere?
up the voltage to the exiting motor?


any factory wrenches out there know anything?
Hando wrote:
I read in MXA that Honda spent close to $100,000 to get the motor to RC's liking. The motor isn't that bad as everyone makes it...
I read in MXA that Honda spent close to $100,000 to get the motor to RC's liking.

The motor isn't that bad as everyone makes it out to be, it just doesn't have the low-end power of the other 250 2-strokes..which are pretty much all YZ clones except for the 250SX.
MxSkillz wrote:
Exactly dude..In 05 they rivised the tps (throttle positioning sensor) which comes from the carb.. sends a signal to the cdi which sends a signal to...
Exactly dude..In 05 they rivised the tps (throttle positioning sensor) which comes from the carb.. sends a signal to the cdi which sends a signal to the servo motor which opens the rc valve at a certain rpm range.. These bikes are underrated.. This technology was adapted from the honda road race team and with a few more tweaks could have been perfect..What it does is provide better traction at the right time. The reason why they feel mellow to everyone is because this system like i said is set up for the correct timing which produces the best traction at the right time..

Coming out of a corner.. everybody wants the most power.. but the more power, the more wheelspin= no traction= spinning out or slower lap times. What they tried to do was brilliant, but not quite right yet.. i wish they would have put more r&d into this cause it was going in the right direction.. But these years can become very potent with a few tweaks to the motor and a few mods for sure.. i have a 05.. and have more power than i will ever need and is a blas to ride.
Good post.

250 2-strokes are so versatile and honestly they are too fast for most people, but what most people fail to realize is that it's easier to slow down a 250 2-stroke than it is to make a 125 or 250F FAST ...

I had an 01 cr250 that i honestly de-tuned because I was so small when I had it and i was only 17..the bike was BLAZING fast but it was too much for me to hang on to until one day I read Dirt Bike magazines review on Juha's 250SXC or whatever it was that he was destroying the GNCC series with...they said that he purposely jetted the bike rich and ran tall gear to tame the motor down and it was easier for him to ride. A light switch went off and I did the same exact thing to my CR250..bingo..bike was easy as hell to ride and still had enough power to get me over any jump.

Im debating on whether or not to get an RM or CR 250 2-stroke but if I get a CR it will be an 04+ with a air-stryker and a set of pipes and maybe reeeds....more than enough power to keep me going fast Smile Smile Smile

MxSkillz
Posts
333
Joined
12/13/2011
Location
Bermuda, BM
12/14/2011 10:49am
Hando wrote:
I read in MXA that Honda spent close to $100,000 to get the motor to RC's liking. The motor isn't that bad as everyone makes it...
I read in MXA that Honda spent close to $100,000 to get the motor to RC's liking.

The motor isn't that bad as everyone makes it out to be, it just doesn't have the low-end power of the other 250 2-strokes..which are pretty much all YZ clones except for the 250SX.
MxSkillz wrote:
Exactly dude..In 05 they rivised the tps (throttle positioning sensor) which comes from the carb.. sends a signal to the cdi which sends a signal to...
Exactly dude..In 05 they rivised the tps (throttle positioning sensor) which comes from the carb.. sends a signal to the cdi which sends a signal to the servo motor which opens the rc valve at a certain rpm range.. These bikes are underrated.. This technology was adapted from the honda road race team and with a few more tweaks could have been perfect..What it does is provide better traction at the right time. The reason why they feel mellow to everyone is because this system like i said is set up for the correct timing which produces the best traction at the right time..

Coming out of a corner.. everybody wants the most power.. but the more power, the more wheelspin= no traction= spinning out or slower lap times. What they tried to do was brilliant, but not quite right yet.. i wish they would have put more r&d into this cause it was going in the right direction.. But these years can become very potent with a few tweaks to the motor and a few mods for sure.. i have a 05.. and have more power than i will ever need and is a blas to ride.
Hando wrote:
Good post. 250 2-strokes are so versatile and honestly they are too fast for most people, but what most people fail to realize is that it's...
Good post.

250 2-strokes are so versatile and honestly they are too fast for most people, but what most people fail to realize is that it's easier to slow down a 250 2-stroke than it is to make a 125 or 250F FAST ...

I had an 01 cr250 that i honestly de-tuned because I was so small when I had it and i was only 17..the bike was BLAZING fast but it was too much for me to hang on to until one day I read Dirt Bike magazines review on Juha's 250SXC or whatever it was that he was destroying the GNCC series with...they said that he purposely jetted the bike rich and ran tall gear to tame the motor down and it was easier for him to ride. A light switch went off and I did the same exact thing to my CR250..bingo..bike was easy as hell to ride and still had enough power to get me over any jump.

Im debating on whether or not to get an RM or CR 250 2-stroke but if I get a CR it will be an 04+ with a air-stryker and a set of pipes and maybe reeeds....more than enough power to keep me going fast Smile Smile Smile

if ur gonna go with the cr250.. go with the 05.. they did alot of positive changes for 05.. but kept those changes right threw to 07 being unchanged from 05 heres the upgrades done for the 05.. The bike is the best handeling bike ive ever ridden..

NEW FOR 2005:
New cylinder design features RC exhaust valve housed in removable case for improved sealing.
New precision-cut stainless steel cylinder base gasket and revised port timing .
New cylinder head combustion chamber shape.
New one-piece exhaust valve for improved sealing.
New piston dome shape.
New piston features single keystone piston ring for reduced friction and improved sealing.
New crankshaft design.
New crankcase with redesigned intake port for smoother air flow and increased journal thickness to decrease crank deflection.
New six-petal reed valve with narrower profile.
New reed valve mounting angle.
New carburetor settings.
New shift fork shaft, shift forks and shift drum.
New ECU mapping and RC valve control settings.
New exhaust pipe shape has increased volume.
Thicker radiator core (from 24mm to 28mm) improves cooling capacity.
New front axle placement for improved fork action and turning.
New swingarm features a dual-axis, double-taper design with a large cast aluminum cross member that is lighter weight and stronger.
New rear hub is stronger and lighter.
New rear shock valving for improved bump absorption.

ENGINE:
New exhaust header and expansion chamber.

CHASSIS / SUSPENSION:
Revised suspension settings.
Camp332
Posts
8770
Joined
8/16/2006
Location
Zoo Jersey, USA
12/14/2011 11:24am
Daaaaaammmnnnn Bro! That thing is super gnar gnar!

Great work
MxSkillz
Posts
333
Joined
12/13/2011
Location
Bermuda, BM
12/14/2011 11:38am
Camp332 wrote:
Daaaaaammmnnnn Bro! That thing is super gnar gnar!

Great work
Thanks bro!
jeffro413
Posts
185
Joined
8/16/2006
Location
Alta, IA, USA
12/14/2011 12:03pm
Wow! You looking for a job!?! lol Great work!
MxSkillz
Posts
333
Joined
12/13/2011
Location
Bermuda, BM
12/14/2011 12:07pm
jeffro413 wrote:
Wow! You looking for a job!?! lol Great work!
sure..you looking to give out a greencard? lol.. Thanks man
Hando
Posts
1571
Joined
11/13/2011
Location
USA
12/14/2011 12:49pm
MxSkillz wrote:
Exactly dude..In 05 they rivised the tps (throttle positioning sensor) which comes from the carb.. sends a signal to the cdi which sends a signal to...
Exactly dude..In 05 they rivised the tps (throttle positioning sensor) which comes from the carb.. sends a signal to the cdi which sends a signal to the servo motor which opens the rc valve at a certain rpm range.. These bikes are underrated.. This technology was adapted from the honda road race team and with a few more tweaks could have been perfect..What it does is provide better traction at the right time. The reason why they feel mellow to everyone is because this system like i said is set up for the correct timing which produces the best traction at the right time..

Coming out of a corner.. everybody wants the most power.. but the more power, the more wheelspin= no traction= spinning out or slower lap times. What they tried to do was brilliant, but not quite right yet.. i wish they would have put more r&d into this cause it was going in the right direction.. But these years can become very potent with a few tweaks to the motor and a few mods for sure.. i have a 05.. and have more power than i will ever need and is a blas to ride.
Hando wrote:
Good post. 250 2-strokes are so versatile and honestly they are too fast for most people, but what most people fail to realize is that it's...
Good post.

250 2-strokes are so versatile and honestly they are too fast for most people, but what most people fail to realize is that it's easier to slow down a 250 2-stroke than it is to make a 125 or 250F FAST ...

I had an 01 cr250 that i honestly de-tuned because I was so small when I had it and i was only 17..the bike was BLAZING fast but it was too much for me to hang on to until one day I read Dirt Bike magazines review on Juha's 250SXC or whatever it was that he was destroying the GNCC series with...they said that he purposely jetted the bike rich and ran tall gear to tame the motor down and it was easier for him to ride. A light switch went off and I did the same exact thing to my CR250..bingo..bike was easy as hell to ride and still had enough power to get me over any jump.

Im debating on whether or not to get an RM or CR 250 2-stroke but if I get a CR it will be an 04+ with a air-stryker and a set of pipes and maybe reeeds....more than enough power to keep me going fast Smile Smile Smile

MxSkillz wrote:
if ur gonna go with the cr250.. go with the 05.. they did alot of positive changes for 05.. but kept those changes right threw to...
if ur gonna go with the cr250.. go with the 05.. they did alot of positive changes for 05.. but kept those changes right threw to 07 being unchanged from 05 heres the upgrades done for the 05.. The bike is the best handeling bike ive ever ridden..

NEW FOR 2005:
New cylinder design features RC exhaust valve housed in removable case for improved sealing.
New precision-cut stainless steel cylinder base gasket and revised port timing .
New cylinder head combustion chamber shape.
New one-piece exhaust valve for improved sealing.
New piston dome shape.
New piston features single keystone piston ring for reduced friction and improved sealing.
New crankshaft design.
New crankcase with redesigned intake port for smoother air flow and increased journal thickness to decrease crank deflection.
New six-petal reed valve with narrower profile.
New reed valve mounting angle.
New carburetor settings.
New shift fork shaft, shift forks and shift drum.
New ECU mapping and RC valve control settings.
New exhaust pipe shape has increased volume.
Thicker radiator core (from 24mm to 28mm) improves cooling capacity.
New front axle placement for improved fork action and turning.
New swingarm features a dual-axis, double-taper design with a large cast aluminum cross member that is lighter weight and stronger.
New rear hub is stronger and lighter.
New rear shock valving for improved bump absorption.

ENGINE:
New exhaust header and expansion chamber.

CHASSIS / SUSPENSION:
Revised suspension settings.
if i can find one for a good price, i will, they seem to fetch considerably more than the older ones.

04's have the newer TC forks but they are still good bikes regardless.
MXEditor
Posts
695
Joined
4/1/2008
Location
Danbury, CT, USA
12/14/2011 1:07pm
Just awesome.

Thanks for that!!!
MxSkillz
Posts
333
Joined
12/13/2011
Location
Bermuda, BM
12/14/2011 1:26pm
thanks! more to come soon.
layinbody31
Posts
530
Joined
11/2/2011
Location
Cedar Lake, IN, USA
12/14/2011 2:05pm
I have to fully agree with everyone here... this thing looks amazing! I plan on picking up an '01 CR250 in the near future and doing...
I have to fully agree with everyone here... this thing looks amazing!

I plan on picking up an '01 CR250 in the near future and doing an '02-'07 plastics conversion on it. I have one question for you though... Where did you get the '11-12 Factory graphics?? I was debating what kind of style/theme to build it with and I think I've found it Smile
MxSkillz wrote:
Yea.. i was lookin for ages for that "factory clean look" here you go mate.. order away. They just made available the new 2012 factory muscle...
Yea.. i was lookin for ages for that "factory clean look" here you go mate.. order away. They just made available the new 2012 factory muscle milk graphic kit as well.. but i prefer these ones better..http://throttlejockey.com/product/x_yQTN93QWawZiMzEY2lkPT/New%20Items

Get the seat cover as well.. sets it off perfect cause they color match the red with the graphics
Thanks for the link Smile

Right after I posted that I remembered that Throttle Jockey is the official graphics provider for Team Honda so I went over to their site and found those. And like you, I also prefer the 2011 graphics to the 2012s. The only thing I noticed was that the black stripe down the center of the seat cover doesn't line up with the black tank on the CR like it does on the CRF. I wonder if you could find a way to add some black Vinyl in that area to make it look more authentic... OR, I have seen a few pics from 2010 where the bike has a full red seat cover. That could match up to the CR shrouds better, and it seems that TJ offers the '10 seat cover (they have options of red/black or red/red)

One thing I would want to know is if it's possible to put a '09up CRF front fender and front number plate on a CR?? I love the V look that the new stuff has!
kyle450rider
Posts
149
Joined
11/26/2006
Location
Jenks, America, OK, USA
12/14/2011 2:06pm
I have to fully agree with everyone here... this thing looks amazing! I plan on picking up an '01 CR250 in the near future and doing...
I have to fully agree with everyone here... this thing looks amazing!

I plan on picking up an '01 CR250 in the near future and doing an '02-'07 plastics conversion on it. I have one question for you though... Where did you get the '11-12 Factory graphics?? I was debating what kind of style/theme to build it with and I think I've found it Smile
MxSkillz wrote:
Yea.. i was lookin for ages for that "factory clean look" here you go mate.. order away. They just made available the new 2012 factory muscle...
Yea.. i was lookin for ages for that "factory clean look" here you go mate.. order away. They just made available the new 2012 factory muscle milk graphic kit as well.. but i prefer these ones better..http://throttlejockey.com/product/x_yQTN93QWawZiMzEY2lkPT/New%20Items

Get the seat cover as well.. sets it off perfect cause they color match the red with the graphics
newmann wrote:
Let me just throw in there that Throttle Jockey refused to hit the print button for me when I needed a set of Woody graphics for...
Let me just throw in there that Throttle Jockey refused to hit the print button for me when I needed a set of Woody graphics for my 2002 CR250 "clean up project". They were still for sale on the website, just out of stock. No reason given as to why they wouldn't print me a set. Thankfully the guys over at 180 Decals hooked me up and the price was very good especially with the artwork involved for a set of one off graphics.

That is one nice bike. I had the woody graphics on my 2003 CRF with yellow backgrounds. It looked great.
MxSkillz
Posts
333
Joined
12/13/2011
Location
Bermuda, BM
12/14/2011 2:28pm
I have to fully agree with everyone here... this thing looks amazing! I plan on picking up an '01 CR250 in the near future and doing...
I have to fully agree with everyone here... this thing looks amazing!

I plan on picking up an '01 CR250 in the near future and doing an '02-'07 plastics conversion on it. I have one question for you though... Where did you get the '11-12 Factory graphics?? I was debating what kind of style/theme to build it with and I think I've found it Smile
MxSkillz wrote:
Yea.. i was lookin for ages for that "factory clean look" here you go mate.. order away. They just made available the new 2012 factory muscle...
Yea.. i was lookin for ages for that "factory clean look" here you go mate.. order away. They just made available the new 2012 factory muscle milk graphic kit as well.. but i prefer these ones better..http://throttlejockey.com/product/x_yQTN93QWawZiMzEY2lkPT/New%20Items

Get the seat cover as well.. sets it off perfect cause they color match the red with the graphics
Thanks for the link :) Right after I posted that I remembered that Throttle Jockey is the official graphics provider for Team Honda so I went...
Thanks for the link Smile

Right after I posted that I remembered that Throttle Jockey is the official graphics provider for Team Honda so I went over to their site and found those. And like you, I also prefer the 2011 graphics to the 2012s. The only thing I noticed was that the black stripe down the center of the seat cover doesn't line up with the black tank on the CR like it does on the CRF. I wonder if you could find a way to add some black Vinyl in that area to make it look more authentic... OR, I have seen a few pics from 2010 where the bike has a full red seat cover. That could match up to the CR shrouds better, and it seems that TJ offers the '10 seat cover (they have options of red/black or red/red)

One thing I would want to know is if it's possible to put a '09up CRF front fender and front number plate on a CR?? I love the V look that the new stuff has!
Ok, cool.. i have the red seat with the black top.. it actually ;lines up perfect.. look on the shroud graphic, the black arch that heads tword the seat.. it lines up exactlt to where the black nline on the seat starts from the front.. it looks authentic for sure. But you can go with the solid red as well, looks awesome..
With the #plate.. ive heard of guys drilling new holes and zip ties for it to work.. but another option is the 2010 crf top triple clamp actually fits on ur bike.. so you could find a cheap on off ebay.. put it on and use the #plate and front fender no problem.

Post a reply to: Cr250 Project Pics

The Latest