Started new thread 2014 CRF 250r full build FS 5/5/2021 6:35 PM

Located in norther new jersey, will work out shipping or meet halfway with anyone serious. 973-885-7029 is best number to contact me please ... more »

This forum thread has 2 replies

Added reply in a thread Crf450 mechanical water pump seal 4/27/2021 12:06 PM

I actually just got a case cover from geico honda with a new seal pressed in, easy fix hopefully it doesnt need to be changed again lol but thanks for help

Added reply in a thread 2014 Honda CRF 250r build (done) 4/11/2021 6:41 PM

Where do you prefer to ride and why other places over FOD? Just curious

Added reply in a thread 2014 Honda CRF 250r build (done) 4/11/2021 2:32 PM

I really just didnt take the turn properly like i had beed on the outside rut, tried to correct it back to the left as i came out towards the right, over corrected and went off the jump sideways a tad. Nothing too bad live and learn

Added reply in a thread 2014 Honda CRF 250r build (done) 4/11/2021 2:30 PM

Rode bike at field of dreams yesterday in new jersey. Had a good time, left early due to crashing on a double. Isnt too bad just sore. Bike ran flawlessly, suspension felt great. I really love the HRC pegs if you think the raptors are sharp these are ... more »

Updated bike check Factory Geico Honda CRF 250r 4/6/2021 4:47 PM
Factory Geico Honda CRF 250r
Updated bike check Factory Geico Honda CRF 250r 4/6/2021 4:47 PM
Factory Geico Honda CRF 250r
Started new thread 2014 honda crf 250r tps sensor 4/4/2021 9:06 AM

Hey guys, Just finished my build, when i start bike it gives me code for bad tps sensor voltage high or low. I dont have the MIS system or a battery supply to test it per manual. MIS seems hard to find. So i got TPS exposed with bike running and just ... more »

This forum thread has 1 reply

Added bike check Factory Geico Honda CRF 250r 4/4/2021 8:03 AM
Factory Geico Honda CRF 250r
Added reply in a thread 2014 Honda CRF 250r build (done) 4/4/2021 7:54 AM

Stoked how it came out. Thanks everyone for the help. Cant wait to ride.

... more »
Added reply in a thread Crf450 mechanical water pump seal 3/21/2021 12:29 PM

Where did you get those special tools to press the mechanical seal in? Having trouble finding one, specifically the 070mf-mena210 which is the installer collar. Im on my 3rd mechanical seal and no luck yet everyone still leaks like crazy. New shaft new ... more »

Added reply in a thread 2014 Honda CRF 250r build (done) 3/18/2021 5:30 AM

Yea engine drain. Not much i can do, if i was going to split cases id be putting a new crank in while im in there anyway. So if this doesnt work full motor build. Well see what happens i have some faith honestly.

Added reply in a thread 2014 Honda CRF 250r build (done) 3/14/2021 1:20 PM

Got a few small things done today. Its all done other than fixing the oil drain threads. I got my helicoil in, but decided against it and going with the time sert should be here later this week. Heres a pic of it 99.99% done

Added reply in a thread 2014 Honda CRF 250r build (done) 3/10/2021 5:23 PM

Yea i wanted to go with time sert just based off forums, but talked to two reputable dirtbike mechanics and both said heli coil. Dont know why but ill trust them, they know more than me. I might buy both and make an educated decision when i see them ... more »

Added reply in a thread 2014 Honda CRF 250r build (done) 3/10/2021 3:44 PM

So went to change my drain bolt washer today as i didnt have any laying around last time i torqued down the drain bolt. Pieces of the threads came out with the old bolt. Doubt i did it as im a torque spec nazi but eitherway threads in case are fucked. ... more »

Added reply in a thread 2014 Honda CRF 250r build (done) 3/7/2021 1:06 PM

Got the bed mount system bolted up today. Pretty easy install and holds bike really well with very little pressure on suspension

... more »
Added reply in a thread 2014 Honda CRF 250r build (done) 3/5/2021 3:06 PM

Got my hands on some HRC pegs and brackets from mxav8r. Thanks alot to him again. The machine work is beautiful think these are my favorite part on the bike. Also got my full ti yoshi system mounted up. High quality and fits great. Torched the welds

... more »
Added reply in a thread 2014 Honda CRF 250r build (done) 3/1/2021 1:24 PM

Lol well theres my issue. Thanks.

Added reply in a thread 2014 Honda CRF 250r build (done) 3/1/2021 1:17 PM

Disc guard from lightspeed mounted. Pretty trick. Any ideas what to do with front brake hose and clamp on fork guard? Dont like up well as seen in pictures even if i pull the line down so the fatter rubber piece is center of clamp it still is too loose

... more »
Added reply in a thread 2014 Honda CRF 250r build (done) 2/26/2021 8:30 PM

Got a more gold chain ERT3. Love the look of it. Also got some pinch clamps and finally found black cv4 hoses. The pinch clamps are a really clean touch. Have HRC pegs on the way, a vortex ecu, carbon front disc guard, dunlop tire stickers, and few other

... more »