Recent Activity
All
gcrites89 Added a reply to Does This Cylinder Need Replated?
3/4/2024 7:22pm I’ll run the hone on it tomorrow and post another picture. Thanks brocster.
More »
brocster Liked a reply to forum topic Does This Cylinder Need Replated?
3/4/2024 7:21pm
I’d hone it a little and see what it looks like and then probably run it if there were no edges on any of the pitts especially in the path of your ring gaps. Proper way would be to bore it or sleeve it.
This forum topic has 44 replies.
FlickitFlat Liked a reply to forum topic Does This Cylinder Need Replated?
3/4/2024 7:14pm
Personally, I have used emery cloth on heads but I don't think I would use it on a cylinder other than to see if it removed in a very small spot. I wouldn't clean it up with one. There is no way you would keep it round. If it did look like it would clean it up, it wouldn't hurt to do a couple swipes with a ball hone. That would sharpen your ports a little but you might like it better. I'm 2/3rds shade tree 3/3rds tight ass.
This forum topic has 44 replies.
Hammer 663s Liked a reply to forum topic Does This Cylinder Need Replated?
3/4/2024 7:12pm
All a matter of budget. A fresh nikasil matched to your new position size is the right way to go. If it’s a beater bike, hone it and run it.
This forum topic has 44 replies.
gcrites89 Added a reply to Does This Cylinder Need Replated?
3/4/2024 7:12pm I want it done right, just didn’t have the extra $400 for the nikasil in my budget. What would be the worst that could happen if I take the hone and run route?
gcrites89 Added a reply to Does This Cylinder Need Replated?
3/4/2024 6:56pm Thanks for your vote wheeels
gcrites89 Added a reply to Does This Cylinder Need Replated?
3/4/2024 6:42pm It is off a 99 KX250 if that helps. I bought a new wiseco piston for it. Not sure if that answers your question.
gcrites89 Added a reply to Does This Cylinder Need Replated?
3/4/2024 6:36pm I have not tried that. Can that remove light pitting?
gcrites89 Added a reply to Does This Cylinder Need Replated?
3/4/2024 6:21pm ?
gcrites89 Added a reply to Does This Cylinder Need Replated?
3/4/2024 6:07pm Going over it with both my finger tip and nail it feels pretty smooth.
gcrites89 Started a new thread Does This Cylinder Need Replated?
3/4/2024 6:01pm Looking for opinions as to whether this cylinder needs replated or if it can just be honed. I left it in my vapor blaster for too long and some pitting appeared. Thanks in advance.
This forum thread has 44 replies.
gcrites89 Added a reply to 99 KX250 Engine Rebuild Query: Idle Gear Contacting Shift Shaft Spring
3/2/2024 8:00pm The stepped collar was not properly seated as you mentioned. The issue is now resolved. Thanks for taking the time to help me with the problem, chuck356!
Village Idiot Liked a reply to forum topic 99 KX250 Engine Rebuild Query: Idle Gear Contacting Shift Shaft Spring
3/2/2024 7:58pm
Cool and yes, that's what I was talking about. Obviously couldn't see in the picture but it wouldn't be the first time I've seen one bumped over inadvertently.
This forum topic has 11 replies.
gcrites89 Added a reply to 99 KX250 Engine Rebuild Query: Idle Gear Contacting Shift Shaft Spring
3/2/2024 7:58pm After further review, there was a snap ring on the inside as you mentioned, however, I did have it installed previously. Chuck356 properly diagnosed the issue. Thank you for taking the time to help me with the issue, Million121.
gcrites89 Added a reply to 99 KX250 Engine Rebuild Query: Idle Gear Contacting Shift Shaft Spring
3/2/2024 7:59pm I have clearance between the end of the shaft (where the shift lever attaches) and the blocking it rests on, if that is what you are referring to. Thanks for the input!
gcrites89 Added a reply to 99 KX250 Engine Rebuild Query: Idle Gear Contacting Shift Shaft Spring
3/2/2024 2:48pm This sounds like it could be the issue. I'll check it out and let you know. Thanks @chuck356!
gcrites89 Added a reply to 99 KX250 Engine Rebuild Query: Idle Gear Contacting Shift Shaft Spring
3/2/2024 2:34pm It would be the small spring on the upper portion of the shift shaft.
gcrites89 Added a reply to 99 KX250 Engine Rebuild Query: Idle Gear Contacting Shift Shaft Spring
3/2/2024 2:31pm In the drawings I am only seeing a snap ring on the outside (flat side) of the idle gear.
gcrites89 Started a new thread 99 KX250 Engine Rebuild Query: Idle Gear Contacting Shift Shaft Spring
3/2/2024 1:44pm 99 KX250 Engine Rebuild. While rotating, the idle gear slightly clicks against the shift shaft spring. It does not hinder rotation, only makes a soft click from the idle gear teeth brushing against the spring. The shift shaft is fully inserted and the idle gear was installed with the shouldered side facing inward. Is this normal? Any help would be...
This forum thread has 11 replies.