Recent Activity
All
Factor E Added a reply to FMF 4.1 repacking issues
3/5/2026 7:56pm If you have rivets yes you neeed to drill them out
More »
Factor E Added a reply to Flywheel holder for late KTM 450s
3/4/2026 7:41pm No
Factor E Added a reply to 23 FC350 Idle issue
3/4/2026 7:38pm Get a new one
Factor E Added a reply to FMF 4.1 repacking issues
3/4/2026 7:35pm You usong a pillow or loose packing? Did you You tube it?
desertratlife Liked a reply to forum topic 23 FC350 Idle issue
3/2/2026 7:21pm
I had something like this a couple of months ago and couldn't figure out what the hell was wrong for months. To this day I still don't know for sure, but what I did that finally got it to run was to pull the throttle body, and clean it really well, especially the connectors. My assumption is that I had a dirty contact. Other thing I have had issues with on KTM's is the spark plug cap cracking. Took me a long time to figure that one out and it will cause some issues as you described.
This forum topic has 28 replies.
Factor E Added a reply to 2021 65SX cutting out/missing at mid-throttle
2/22/2026 7:28pm Plug, coil, stator, reeds
Factor E Added a reply to 23 FC350 Idle issue
2/22/2026 7:19pm Cylinder head temp sensor Did you try starting after cool down?
EAmato88 Liked a reply to forum topic Time to get a 65, looking for advice/opinions.
2/17/2026 8:41pm
Youd be insane to buy anything but a yz65. Hundreds hours of literally bullet proof reliability. Ive personally owned those bikes with over 300 hours still on the original clutch cable. Mark my words, if you buy a sub 2000 dollar ktm 65, youre going to regret your decision week 1.
This forum topic has 7 replies.
walent215 Liked a reply to forum topic 2018 Yamaha YZ250F part
2/11/2026 4:58am
Brake pedal pivot bolt
This forum topic has 5 replies.
Factor E Added a reply to 2016 FE450 - Intermittant rear brake loss
2/9/2026 9:17pm Work your way bleeding back to caliper Hold pedal dow and crack banjo fitting at master cylinder then do same to rear banjo then bleed screw
Thornton_Melon Liked a reply to forum topic 2024 YZ250 Linear Power
2/8/2026 4:22pm
HITLIS power valve https://productivepowerllc.com/products/hitlisyz250 DRT head dome A or B https://www.berad-products.com/products/drt-cylinder-head-yamaha-yz250x…
This forum topic has 13 replies.
Factor E Added a reply to newer xtrig on older ktm
2/5/2026 4:14am WHICH DID YOU TIGHTEN FIRST PINCH BOLTS OR STEM NUT? STEM NUT SHOULD BE FIRST
stimacr Liked a reply to forum topic 23 FC350 Idle issue
2/2/2026 2:24pm
I just reset my TPS to .40 with the butterfly closed and about .56 idle screw in and .66 for cold start. Seems like the bike starts a lot better than before and idles a bit smoother.
This forum topic has 28 replies.
Factor E Added a reply to 2026 CRF250R casting flaw?
2/1/2026 9:19pm MAYBE WORKED AFTER CASES CAME OUT OF THE MOLDS GO BACK TO DEALER AND LOOK AT ANOTHER ONE
RockyRider Liked a reply to forum topic Deposits in exhaust port 23 YZ450
1/31/2026 6:59pm
Noted, thank you guys. I’ll stray away from straight leaded and do a 50/50, it’s just hard to trust pump fuel in CA these days.
This forum topic has 8 replies.
Factor E Added a reply to 24 KX450 counter shaft bearing
1/26/2026 11:34am Clean really well and seal it Your going to put a seal over it If its going to leak I would guess drops until you need to split cases
Factor E Added a reply to 23 FC350 Idle issue
1/25/2026 1:58am You need to check pump pressure Both idle and tps have a measured value setting using the dealer diagnostic tool
Factor E Added a reply to 01cr250 hinson clutch pack extra top hat washer
1/15/2026 8:16pm The top hat is at end of the push rod for the pressure plate
Factor E Added a reply to Cr125 hard starting
1/9/2026 9:42pm Hrs on cylinder? A or B piston installed? Broken ring or ring gap Was head surfaced?
Factor E Added a reply to 2006 YZ450F carb_airboot
1/8/2026 9:25pm Measure the old one against the new to make sure