Added reply in a thread 94 RM125 and 07 RM125 Parts 7/5/2017 6:28 PM

Any pics of the sst pipe?

Added reply in a thread 2007 crf 250 part out 4/16/2017 7:49 PM

Price on complete head and cam? Thanks

Added reply in a thread 2011 Rmz 250 issues 3/23/2017 5:24 AM

Yea I cant disagree with you there. I've seen some pretty hacked up and unmaintained used bikes in the past. I'm gonna throw a new top end in and hopefully that solves the issue. Thanks

Added reply in a thread 2011 Rmz 250 issues 3/21/2017 12:42 PM

I switched the cam timing over to the compression tdc (had it on ignition) and I reset my idle knob to 5-6 turns as per reccomomendation in the manual. after about 20-25 kicks the bike fired up with the choke on and I let it idle. As soon as I shut the ... more »

Added reply in a thread 2011 Rmz 250 issues 3/18/2017 11:17 AM

If it were a bad senor would I still be getting spark?

Added reply in a thread 2011 Rmz 250 issues 3/17/2017 5:06 AM

Yes I put something down the plug hole to confirm it's at tdc

Added reply in a thread 2011 Rmz 250 issues 3/16/2017 8:58 AM

If it were to be anything electrical like one of the sensors would I still be getting spark?

Added reply in a thread 2011 Rmz 250 issues 3/15/2017 2:32 PM

Okay so I got the new cam chain put in and still same issue. Here are some pics to confirm timing

... more »
Added reply in a thread Kx250f warp 9 wheel set 18" rear $300 3/3/2017 4:37 PM

Thanks guys^^

Added reply in a thread Kx250f warp 9 wheel set 18" rear $300 3/3/2017 3:13 PM

I'm not too sure if theyd fit. I haven't ridden the 18 rear on a 250 2t so I can't really comment on that but I will say there wasn't a huge notable difference on my 250f switching from the 19

Added reply in a thread Kx250f warp 9 wheel set 18" rear $300 3/3/2017 9:31 AM

Bump 300 obo

Added reply in a thread 2011 Rmz 250 issues 3/1/2017 3:47 AM

Thanks. Previous owner told me the 450 part was installed.

Added reply in a thread 2011 Rmz 250 issues 2/28/2017 5:13 PM

Okay I had the head off and the top end looked pretty new. The PO said it had a newer top end so I pulled it apart to take a look. Valve seats were pretty good and valves seated fine. threw brand new gaskets in it and put it all back together. Gonna ... more »

Started new thread 2011 Rmz 250 issues 2/28/2017 5:45 AM

So Recently I bought a 2011 rmz 250. When I first got it, the bike was hard to start. Took about 10-15 kicks before it would fire and after it started it ran decent. Took it apart and the valve clearances were quite a bit off. Adjusted the valves to ... more »

This forum thread has 14 replies

Added reply in a thread RM stuff/pro carbon disc guard/clutch perch for sale 2/21/2017 10:27 AM

Still have the brake pedal and frame guards? Email me if it's easier @ajf88@comcast.net

Added reply in a thread How to ship a dirt bike 10/21/2016 1:14 PM

I've heard a lot of good things about the site Uship.

Added reply in a thread Suzuki RMZ / RM parts 10/11/2016 1:36 PM

Email sent

Started new thread Kx250f warp 9 wheel set 18" rear 21" front $300 10/8/2016 2:34 PM

Selling a set of warp 9 complete wheels with tires. They came off of an 08 kx250f but should fit other years and models. 21 inch front and 18 inch rear. Please check to verify they will fit your bike first. The wheels have normal scratches and markings

... more »

This forum thread has 1 reply

Added reply in a thread First attempt at suspension rebuild gone very wrong 10/7/2016 2:57 PM

So bleed with the cap on? if so How does the air escape and also how do I know when there is no more air in the system? How much fluid do I pour in? I was filling it up to about a half inch below the holes. And when you say returning fully, I should ... more »