Queen's 1990 Kawasaki KX125 minimal rebuild

profmur
Posts
206
Joined
3/13/2024
Location
Somewhere, NJ, USA
11/11/2026 5:33am
This bike is fighting me every step of the way.Dropped the frame off for powder coating, and the shop told me their professional blasting equipment was...

This bike is fighting me every step of the way.

Dropped the frame off for powder coating, and the shop told me their professional blasting equipment was barely touching whatever finish is currently on it. They regularly blast motorcycle frames without any trouble, but apparently this one is unusually stubborn. They suggested having it chemically stripped first.

So I have two questions:

  1. What kind of paint or factory finish would be this resistant to abrasive blasting?
  2. Would something like aircraft paint stripper be effective against a finish that's proving this difficult to blast off?

For context, this is an experienced shop that blasts frames routinely, so I'm more interested in figuring out what this coating might be and how best to remove it than troubleshooting their equipment.

Anyone run into something similar?

I've had good and ok results with consumer available paint stripper on metal, it depends on the paint.  I've needed a few applications with some industrial type paints that were stubborn.

Does the powder coater have a professional recommendation for someone that does professional chemical stripping?  Usually it's the same type of business that does professional plating.   They have the vats of stripper chems, just dunk, wash/neutralize, and voila, now you have bare metal.

11/11/2026 9:04am
profmur wrote:
I've had good and ok results with consumer available paint stripper on metal, it depends on the paint.  I've needed a few applications with some industrial...

I've had good and ok results with consumer available paint stripper on metal, it depends on the paint.  I've needed a few applications with some industrial type paints that were stubborn.

Does the powder coater have a professional recommendation for someone that does professional chemical stripping?  Usually it's the same type of business that does professional plating.   They have the vats of stripper chems, just dunk, wash/neutralize, and voila, now you have bare metal.

How do the aircraft strippers work on existing powder coat? 

profmur
Posts
206
Joined
3/13/2024
Location
Somewhere, NJ, USA
11/11/2026 11:44am
profmur wrote:
I've had good and ok results with consumer available paint stripper on metal, it depends on the paint.  I've needed a few applications with some industrial...

I've had good and ok results with consumer available paint stripper on metal, it depends on the paint.  I've needed a few applications with some industrial type paints that were stubborn.

Does the powder coater have a professional recommendation for someone that does professional chemical stripping?  Usually it's the same type of business that does professional plating.   They have the vats of stripper chems, just dunk, wash/neutralize, and voila, now you have bare metal.

How do the aircraft strippers work on existing powder coat? 

This is why I was nudging you to ask the powdercoater if they have a commercial  stripping/plating contact. 

If media blasting isn't putting a dent in the coating then said coating is on the stouter side of the spectrum.

I have had luck with chem stripping industrial powdercoat off a large piece of diamond plate machinery but it required a few coats/passes.  The stuff is nasty to work with and it's not inexpensive.

 

11/11/2026 11:58am Edited Date/Time 11/11/2026 11:59am
profmur wrote:
I've had good and ok results with consumer available paint stripper on metal, it depends on the paint.  I've needed a few applications with some industrial...

I've had good and ok results with consumer available paint stripper on metal, it depends on the paint.  I've needed a few applications with some industrial type paints that were stubborn.

Does the powder coater have a professional recommendation for someone that does professional chemical stripping?  Usually it's the same type of business that does professional plating.   They have the vats of stripper chems, just dunk, wash/neutralize, and voila, now you have bare metal.

How do the aircraft strippers work on existing powder coat? 

profmur wrote:
This is why I was nudging you to ask the powdercoater if they have a commercial  stripping/plating contact. If media blasting isn't putting a dent in the...

This is why I was nudging you to ask the powdercoater if they have a commercial  stripping/plating contact. 

If media blasting isn't putting a dent in the coating then said coating is on the stouter side of the spectrum.

I have had luck with chem stripping industrial powdercoat off a large piece of diamond plate machinery but it required a few coats/passes.  The stuff is nasty to work with and it's not inexpensive.

 

The guys that built my engine think they can get it done with a product from the hardware store, and his dad does very affordable powder coating (and he's an excellent welder should we need any of that).  They are applying the stripper tonight, will cover it with plastic and let it sit. 

Gonna see what they can do with it and go from there. 

Maybe I should have just run what I had.. in way over my head with $$$ on this build already.  I have the $ it's more that this is a 125 and I will lose a ton of money when it comes time to clear out space in the garage later on.

1

The Shop

11/11/2026 12:01pm

A different powder company quoted me $250 just to strip it off, and another $300 for powder. I just can't.. got to draw a line somewhere. My shop was going to be $200 to powder it, which I could stomach. 

1
profmur
Posts
206
Joined
3/13/2024
Location
Somewhere, NJ, USA
11/11/2026 3:50pm
A different powder company quoted me $250 just to strip it off, and another $300 for powder. I just can't.. got to draw a line somewhere...

A different powder company quoted me $250 just to strip it off, and another $300 for powder. I just can't.. got to draw a line somewhere. My shop was going to be $200 to powder it, which I could stomach. 

Yes, that price is excessive.  

The plan to use the hardware store available stripper sounds reasonable.  Be sure to post some before and after photos.

1
ace402
Posts
313
Joined
9/23/2019
Location
Loxley, AL, USA
11/12/2026 12:59pm
A different powder company quoted me $250 just to strip it off, and another $300 for powder. I just can't.. got to draw a line somewhere...

A different powder company quoted me $250 just to strip it off, and another $300 for powder. I just can't.. got to draw a line somewhere. My shop was going to be $200 to powder it, which I could stomach. 

profmur wrote:

Yes, that price is excessive.  

The plan to use the hardware store available stripper sounds reasonable.  Be sure to post some before and after photos.

Unfortunately I think that’s close to what I paid for my YZ250 to get done in Bentley Blue. However that color requires a silver base coat if I recall correctly.

Sparkalounger
Posts
1725
Joined
4/1/2008
Location
Minneapolis, MN, USA
11/13/2026 6:40am

$60. in Pj1 spray paint... 😁

I was just saying the build would look nice to at least start out fresh looking. Get the initial pics... A lot of work ($) for the dirty frame to be what the eye is immediately drawn to...

Oh Queen... Love your build here, thank you for bringing us along!

This will always be known as Queens " minimal " build! 👍😁

3
Kidkawie
Posts
1197
Joined
8/31/2012
Location
ქუთაისი, GE
11/15/2026 10:17pm

Paint code is 777, or RAL 6018.

I can buy it in spray cans, lol.

20220301 123818
2
11/16/2026 9:01am
Kidkawie wrote:
Paint code is 777, or RAL 6018.I can buy it in spray cans, lol.

Paint code is 777, or RAL 6018.

I can buy it in spray cans, lol.

20220301 123818

I have two cans of the PJ1. Rattle can paint rubs off much quicker than powder. Probably fine for bikes that aren't ridden much though.

1
BoxcarWilly
Posts
1321
Joined
10/5/2023
Location
Thunder Bay, ON, CA
11/16/2026 9:04am

I don't like powder anyway. It's too heavy and looks too bulky. I'd rather touch the paint up over time. 

 

PJ1 was a perfect match for my 2000 KX125 I rebuilt a couple winters ago. 

Kidkawie
Posts
1197
Joined
8/31/2012
Location
ქუთაისი, GE
11/16/2026 10:19am

I have two cans of the PJ1. Rattle can paint rubs off much quicker than powder. Probably fine for bikes that aren't ridden much though.

Rattle can paint will last if you install frame guards.  I used to cut panels for the frame above the frame guards from clear backgrounds.

PJ1 is epoxy, so if you need primer then use PJ1 primer.  I had an issue with that before, ruined a gas tank paint job.

I sprayed my frame with single stage urethane mixed at an auto body shop, its equivalent to powder as far as durability goes.

Kidkawie
Posts
1197
Joined
8/31/2012
Location
ქუთაისი, GE
11/16/2026 11:16am

Funny story on the urethane paint.....

I went to a auto body paint supply with a set of NOS bars.  This was back in 2012ish before the paint codes were well known, guy scanned the color, mixed the paint.  WTF did I know, I just sprayed it.  Came out great...wrong color.  Went back to retint it.  I swear the guy was color blind and kept messing up the tint.  I took over "Bro, add some yellow....add some white, etc"  finally got the match dabbing it on the bars. Had to respray the whole frame.

1 day ago

Still waiting on frame powder.  

Got the swingarm back today. With a little luck and good fortune, I'll have the frame and subframe back next week. 

swingarm3swingarm2swingarm1
6
profmur
Posts
206
Joined
3/13/2024
Location
Somewhere, NJ, USA
1 day ago Edited Date/Time 1 day ago
Still waiting on frame powder.  Got the swingarm back today. With a little luck and good fortune, I'll have the frame and subframe back next week. 

Still waiting on frame powder.  

Got the swingarm back today. With a little luck and good fortune, I'll have the frame and subframe back next week. 

swingarm3swingarm2swingarm1

I take it the chem paint stripper was successful?  How was the metal underneath?

1 day ago Edited Date/Time 1 day ago
Still waiting on frame powder.  Got the swingarm back today. With a little luck and good fortune, I'll have the frame and subframe back next week. 

Still waiting on frame powder.  

Got the swingarm back today. With a little luck and good fortune, I'll have the frame and subframe back next week. 

swingarm3swingarm2swingarm1
profmur wrote:

I take it the chem paint stripper was successful?  How was the metal underneath?

Swingarm was not powdered before, so they were able to blast it normally, then paint with cerakote. If it ends up scratching easy I can always pull it and have it powdered later. 

The frame/subframe stripping wasn't completely successful. Unfortunately I don't have after pics, but the stripper (I think Jasco) did not get all of the paint off, this after several days of soaking while covered with plastic. 

They are having to go back and sandblast what it couldn't get. The guy doing the sandblasting is a welder (and a good one). They will let me know if they find anything that needs additional repair.  He said he's never seen a coating this difficult to remove, and they work with a lot of powder removal/refinish projects. 

Nairb#70
Posts
4461
Joined
2/25/2020
Location
Ivoryton, CT, USA
1 day ago
Still waiting on frame powder.  Got the swingarm back today. With a little luck and good fortune, I'll have the frame and subframe back next week. 

Still waiting on frame powder.  

Got the swingarm back today. With a little luck and good fortune, I'll have the frame and subframe back next week. 

swingarm3swingarm2swingarm1

Wow, remember what small diameter axles and pivot shafts we had back then. It was shortly thereafter that swingarm pivots and wheel axles grew in size quite a bit which stiffened up the chassis quite a bit too.

1

Post a reply to: Queen's 1990 Kawasaki KX125 minimal rebuild

The Latest