Tweaked front end

lawson34
Posts
719
Joined
1/19/2019
Location
London, KY, USA
I went down and knocked everything out of line, I went thru the procedure to realine everything got back on the bike it seems to still be off so I loosened the steering stem nut and repeated the process but it's still don't look right setting on the bike... Any ideas guys it's good enough to ride but its buging the sit out if me? Thx
|
mxgreg85
Posts
58
Joined
4/1/2008
Location
USA
2/17/2019 4:53pm
If you bent your fender, that can give the illusion that everything else is out of line. I've done the same thing, lined everything else back up but because the fender was tweaked it made the whole front end look off. Plastic is hard to get straight once it is bent, usually takes heat and nearly impossible to get perfect again. It can be hard to tell when the fender is on the bike, but if you take it off and run something straight along the center line (like a metal tape measure), that will tell. If you have rubber mounted triple clamps, those also move pretty easy in a crash, take the bar mounts off and make sure the rubber cones are set evenly.
CarlinoJoeVideo
Posts
7516
Joined
11/30/2013
Location
Portland/Los Angeles, CA, USA
2/17/2019 5:17pm
Maybe need to loosen your bar mounts and reset those.
2
lawson34
Posts
719
Joined
1/19/2019
Location
London, KY, USA
2/17/2019 7:01pm
Maybe need to loosen your bar mounts and reset those.
Yeah that was the first thing I did my wheel is slightly turned to the left that's my problem
lawson34
Posts
719
Joined
1/19/2019
Location
London, KY, USA
2/17/2019 7:08pm
The site has a lot of knowledgeable dudes, I'd appreciate any suggestions

The Shop

Wade221
Posts
620
Joined
12/2/2015
Location
Yuba City, CA, USA
2/17/2019 7:18pm
Could be the fork legs/axle is just slightly twisted. Pull the forks, re-install, re-install wheel. Check alignment.
lawson34
Posts
719
Joined
1/19/2019
Location
London, KY, USA
2/17/2019 7:26pm
I loosened up all the pinch bolts, move both legs around in the clamps but I havent removed the wheel... thx for the reply guess I'll pull the wheel
lawson34
Posts
719
Joined
1/19/2019
Location
London, KY, USA
2/18/2019 6:26am
Bump
brody
Posts
418
Joined
11/26/2018
Location
USA
2/18/2019 6:54am
maybe your fender is bent
or your triple clamps, and you could have tacoed a wheel
1
lawson34
Posts
719
Joined
1/19/2019
Location
London, KY, USA
2/18/2019 7:01am
Locked the front brake up it pile drived my ass
seth505
Posts
10230
Joined
4/1/2008
Location
SD, CA, USA
2/18/2019 7:04am Edited Date/Time 2/18/2019 7:04am
When this happens to me I pull the front fender off so I can see everything else and make sure they are good.
-Are clamps straight/in line with each other?
-Are bar mounts bent/twisted?
-Are handlebars tweaked?
-Spin front wheel, is it out of round?

It's really common that the bars or bar mounts will be tweaked on one side (even slightly bent) so be mindful of that throwing things off as well.
captmoto
Posts
5929
Joined
4/22/2009
Location
Rancho Cucamonga, CA, USA
2/18/2019 7:15am
seth505 wrote:
When this happens to me I pull the front fender off so I can see everything else and make sure they are good. -Are clamps straight/in...
When this happens to me I pull the front fender off so I can see everything else and make sure they are good.
-Are clamps straight/in line with each other?
-Are bar mounts bent/twisted?
-Are handlebars tweaked?
-Spin front wheel, is it out of round?

It's really common that the bars or bar mounts will be tweaked on one side (even slightly bent) so be mindful of that throwing things off as well.
I'm going with bent bar mounts.
fourfourone
Posts
3046
Joined
10/14/2017
Location
86oh, CT, USA
2/18/2019 7:18am
I had an issue aligning the bar mounts on my yz450f. I tweaked the mounts and since they are rubber I was having a hard time getting them to be perfectly aligned. I eventually left everything a hair tight turned then bars to one side and pulled until it looked straight. tighten everything down and it was fine. I use the top of the fork tubes to sight the bars in and make sure its all even.
lawson34
Posts
719
Joined
1/19/2019
Location
London, KY, USA
2/18/2019 7:52am
Thx guys
seth505
Posts
10230
Joined
4/1/2008
Location
SD, CA, USA
2/18/2019 8:14am
On the topic of bar mounts, I've had to remove them for friends to verify. You can see pretty easily if the bolt that mounts in to the top clamp is bent (even slightly).
lawson34
Posts
719
Joined
1/19/2019
Location
London, KY, USA
2/18/2019 8:55am
My bars and mounts seem straight the wheel is slightly turned left may just be me I did hit my head lmao

Post a reply to: Tweaked front end

The Latest