Recent Activity
All
Lentz197 Liked a reply to forum topic Fork Storage Bucket --- STOP THE INSANITY, BUILD THIS!
8/25/2026 12:00pm
Im too poor to have fork problems like this LOL
This forum topic has 13 replies.
Tuplavee Added a reply to Chinese quality revisited
8/15/2026 5:48am Even though it has been tempting sometimes, I don't buy any critical weigh/stress bearing chinesium parts. My NiceCNC rear master cylinder protector broke after 40hours. A part what you might think to last forever as long as there is material left to wear
3strokemx Liked a reply to forum topic How many hours for a “used” bike
7/31/2026 8:58am
How do you find specs for bolt torque and valve clearances?
This forum topic has 43 replies.
Tuplavee Added a reply to 2023 YZ125 - Jetting Fix
6/25/2026 9:28am I'd recommend to try Y4 needle. It's been best for me I did not get those CCx or N3xx needles work as good. Tried several.
Tuplavee Added a reply to No-toil Alternatives
6/11/2026 3:25am In this part of Europe we have had delivery problems for years. Kind of "alway buy some when you see it in stock"
Tuplavee Added a reply to Is 10w 40 oil ok in a 2 stroke gearbox?
5/31/2026 12:06am I have used about the cheapest 10W40 with API SJ/JASO MA 2 rating in Austrian two strokes and YZ. Hundreds of hours
Tuplavee Added a reply to Chest protector with shoulder protection worth it?
5/18/2026 7:13am I highsided shoulder first to a jump face last year and cracked a collarbone. Had Leatt logo in my shoulder for over a week. I believe without shoulder protector it would have been way worse I trust Leatt style undershirts which have only shoulder and elbow protection (3DF etc), maybe light kidney belt. Then a chest/back protector over shirt. Fox...
Tuplavee Added a reply to Power jet tuning in Keihin PWK
3/22/2026 12:59pm So the solenoid valve is supposed to close power valve circuit when powered. Today out of curiosity I measured YZ125 2022 as following: ~24 Ohms resistance, 12V click test ok. Input voltage 0,5V at idle and 23V after 1/8 throttle. Connector plugged I got ~7V at rpms Isn't it working the opposite as it should? Has anybody else measured input...
Tuplavee Added a reply to NEKEN SFS TRIPLECLAMP BARMOUNTS
3/21/2026 9:48pm Why not just over pressurize them
MOTO13 Liked a reply to forum topic Kawasaki two strokes … Over it
12/8/2025 6:44am
Kawi's been over it for 20 years. Yamaha on the other hand, seems to be doing quite nicely and never got the memo that the 2 stroke was dead.
This forum topic has 62 replies.
Tuplavee Added a reply to 4.0 to 5.0 Mikuni slide (AJ/Digger/FGR thread spill over)
11/26/2025 11:35am I originally had 4.0 and 5.5 Mikuni OEM slides but the 5.5 lost it's plating so I used it as reference for grinding(and initial test fitting with sockets) with and would say definitely it was also wider, but not deeper. So I kept the "edge of the barrel" about in the same place
Tuplavee Added a reply to 125/150/250/300 KTM/HUS/GG jetting thread
11/26/2025 8:21am 0-30celsius I had the MJ always same, rich enough For spring and autumn one/two size bigger PJ and maybe one clip at the needle when it started to bog on throttle openings
Tuplavee Added a reply to 4.0 to 5.0 Mikuni slide (AJ/Digger/FGR thread spill over)
11/26/2025 8:03am If I remember right, it's a a straight cylinder shape "bore" so you can use correct size socket for test fitting. As rough example - if xx mm socket(OD) fits snug to 4.0 cutout, use xx +2mm for test fitting 5.0 shape. Also follow scraped 1mm line at the front. Combine top right and bottom left of your drawing 
Tuplavee Added a reply to Mid level boots
11/22/2025 12:14pm Pretty much the same as Atojos without SRS. Atojos have worked great for me +200hours and just bought a spare part set(pivots, soles etc) to get another 200h Much more support than Tech7, but still close to zero break in time. I also have new unused Crossairs and there is only very little difference to my old Atojos in the...
EuroGuy39 Liked a reply to forum topic MXoN - Saturday: Practice + Qualifying
10/4/2025 12:13pm
Pretty good ride for Haavisto in 14th. Finland might get to A final
This forum topic has 526 replies.
8500rpm Liked a reply to forum topic MXoN - Saturday: Practice + Qualifying
10/4/2025 12:12pm
Happy for Gifting and great that Haavisto did well
This forum topic has 526 replies.
Shaned9326 Liked a forum topic MXGP RACE 2!!
8/17/2025 12:53pm
Do yourself a favor and go watch that race!! Straight Fire🔥🔥🔥
This forum topic has 47 replies.
Elliot Liked a reply to forum topic MXGP RACE 2!!
8/17/2025 12:53pm
Content cannot be rendered.
This forum topic has 47 replies.
Tuplavee Added a reply to 2026 YZ125 jetting
8/5/2025 12:51pm My guess is that intake box is only modified so that it fits same throttle position sensor as in yz250 which has cable pointing downwards. But just a guess.
Tuplavee Added a reply to 2026 YZ125 jetting
8/4/2025 12:20pm I got my slide from https://www.ktmschnellversand.de/ . Might have been the last one as it seemed to be very old stock. KTM part number is 54631235055, good luck. Maybe the #7 slide will work too as it is still standard in 2026 but haven´t tested. Check the other thread for needle holder information, you need different non-spring-loaded needle holder too...