Added reply in a thread 2022 ktm 125xc with keihin 38 a/s 6/20/2022 6:59 AM

Digger, I pm'd you on another jetting topic did you get my message ?

Added reply in a thread De tuning the SX/TC/MC 250 two strokes 5/9/2022 6:27 AM

I have the same bike, and mild mannered Vet fits me too... I swapped for the green PV springs but after few rides I might go back to the yellow and really spend more time to fine tune I unplugged the connector under the tank for the more "mellow" ignition ... more »

Added reply in a thread De tuning the SX/TC/MC 250 two strokes 5/9/2022 6:13 AM

Opyguy, I pm'd you about jetting, did you get my message ?

Added reply in a thread 22 ktm sx 250 suspension help 4/13/2022 6:25 PM

+1 22 GasGas MC250, Slow 55 y/o Vet C- ! The Austrians need the correct rear spring if you want the front to work. If the rear is too low, the forks don't get the load to work properly regardless of air pressure and clickers adjustments I'm 215 lb and ... more »

Added reply in a thread 125/150/250/300 KTM/HUS/GG jetting thread 4/5/2022 3:11 PM

22 GasGas MC250, Central FL , you could pick the 42 or 43 and start on middle clip then adjust. FL average altitude is100 ft , TX where's AJ ~ 1700 ft and Colorado 6800 ! So pilot and main jet you'll have to test and tweak. On my MC : AJ's specs (I got ... more »

Added reply in a thread 2021 KTM 350 SX-F Suspension Help 4/4/2022 12:41 PM

Mind sharing what is your spring rate ? The Austrians have a very "unique" OEM spec. on their machines Always on the light side, even for the heavier bikes and it seems their rate/rider weight recommendations rarely match what all suspension companies ... more »

Added reply in a thread 125/150/250/300 KTM/HUS/GG jetting thread 4/1/2022 12:17 PM

Listen to AJ... For a short time I just had the slide as I was waiting for the other parts but that alone was a main game changer. The jets/needle/needle jet were what made this whole setup a complete and reliable package. I'm not crazy fast either but ... more »

Added reply in a thread 2021 Xact suspension settings and set ups 3/25/2022 4:04 AM

I just got a 22 GasGas MC250 5 hours on it now , 55 y/o Vet C The forks are not bad at all but I learned that balance is the key and if the rear is not set properly, the front won’t feel right or not good as it could be . The spring rate choices from ... more »

Added reply in a thread 125/150/250/300 KTM/HUS/GG jetting thread 3/24/2022 3:25 AM

Outlaw Racing fuel - 96 or 110 and Maxima K2 Pump gas is loaded with ethanol here.

Added reply in a thread 125/150/250/300 KTM/HUS/GG jetting thread 3/23/2022 1:21 PM

22 GasGas MC250, Central FL so weather conditions very close and elevation not that much more above on your side) AJ's specs (I got PV set differently but that's personal pref. MJ 490 PJ 32.5 AS ~ 1.5 turns out Needle jet S4 Needle 42-75 on the 2nd clip ... more »

Added reply in a thread GASGAS MC 450 suspension settings 11/1/2021 6:04 PM

I have the MC250F and at 200 lbs like you, the stock 42N/mm rear spring which is stock on their 250/450 is way too soft. Even for my slow Vet C level I tried a 48 but even with minimum preload it feels too firm and static sag on the high end Trying a ... more »

Added reply in a thread Locals price gouging used clapped bikes 3/31/2021 2:31 PM

My one and only serious buyer is in ID, (Preston) shipping $ just ridiculous

Added reply in a thread Locals price gouging used clapped bikes 3/31/2021 12:58 PM

Well i don't know if it's wrong time/area/model but my far from clapped 19 TC is still sitting After 1+ month on FB Marketplace/ktmtalk/Cycle Trader/Vital : 5 tire kickers 2 low ballers 1 serious guy but in a not well deserved area so shipping quotes

tongue
... more »
Started new thread 2019 HVA TC 250 - Central FL Lowered price now $6,000 3/10/2021 6:53 AM

For sale is my HVA 2019 TC250 - $6,800 Bike is in consignment at Becks tech, very reputable suspension and engine work shop 945 Alexander Ave#4, Port Orange, FL 32129 Phone: 386-256-4776 (shop) , or 417-459-9255 (cell) First owner, slow 54 y/o Vet C,

... more »

This forum thread has 1 reply

Added reply in a thread ISO 2020 KTM 250 SX Tips 3/2/2021 5:43 PM

All you need to know about jetting the Mikuni without breaking the bank is here : AJ setup works plain and simple : https://www.vitalmx.com/forums/Tech-Help-Race-Shop,42/KTM-HUS-125-150-250-jetting-thread,1363394

Added reply in a thread Picking Up a 2019 KTM 150sx...What to Know 12/24/2020 8:43 AM

Not trying to steer anybody to spend $$$ on a Keihin or Lectron but AJ's thread is spot on Works wonders on my 19 TC 250. Re-jetted a friend's 150 SX (2017) -per the AJ]s specs Fast A rider and he was beyond thrilled by how clean and crisp it is running ... more »

Added reply in a thread KTM SX250 Sand riders: What MJ at colder temps? 12/11/2020 7:03 AM

I concur... Got AJ specs on my 19TC250 and snappy (read violent!) is on point. I am going to richen this setup and play more with the powervalve to tame it a bit. Nevertheless , the bike runs great, no gargle or hiccup No longer affected as temp/humidity ... more »

Added reply in a thread RC4 on YCF190 12/4/2020 7:11 AM

I got my 9 y/o kid the 88 model and I got to ride the whole 2020 model range No issues they are very solid bikes. Part availability Not a problem. On our 88 the electric start works flawlessly Engine rock solid. Tons of bling to upgrade and larger models

... more »
Added reply in a thread What's it worth? 2018 Husky TC 250 with 6.8 hrs. 10/7/2020 11:59 AM

Keep it (seems you don't really want to sell anyway!) I regretted selling most of my 2 strokes For ref, my 19 TC250 : 38 unmolested hours (slow Vet C) R/T spring conversion- revalved F/R Ride Eng link and knuckle Boyesen Rad Valve Jetted per AJ thread ... more »

Added reply in a thread 125/150/250/300 KTM/HUS/GG jetting thread 10/1/2020 6:40 AM

Central FL temps and altitude not far from TX conditions On my TC , I run 50:1 and it was feeling a bit lean down low and at startup Bumped the PJ to 35 and it took care of it. Needle clip is at 2.5 Position (using a JD washer/spacer ring) and I might ... more »