Recent Activity
All
mx724 Started a new thread 2014-2016 yz250f setup (fork height & sag)
5/10/2019 12:26pm Just looking for comparisons of what works what doesn't. Where are you guys running you sag, fork height, and rear wheel? Im at about 5mm up in fhe clamp but want to go more as front ....still feels a bit vague.
This forum thread has 5 replies.
mx724 Added a reply to 2014-2016 yz250f setup (fork height & sag)
5/10/2019 9:19am Just to confirm when u say 5mm up, from top of cap, where cap meets fork... or the first line on forks closest to the top?
More »
mx724 Started a new thread ODI lock on grips
1/20/2019 4:28am First time using these on a 214 yz250f. What do you guys do with the throttle side spacer/ washer? Does it get used or? Otherwise things seem pretty nice. Guess will see how the hold up under use. Also noticed that the instructions recommended the A cam but you could also use the J cam, and ironically the J cam...
This forum thread has 1 reply.
mx724 Added a reply to YZ250f and 450 parts and cheap gear
12/29/2018 8:19am email sent.
mx724 Added a reply to 2014 YZ 450F Akrapovic exhaust, JGR Pull Rod, GYTR tuner
11/16/2018 7:46am Does the pull rod fit 2014 250fs as well? How much for bars and pull rod?
mx724 Added a reply to Yz 250 crank
10/29/2018 11:55am Is the siezed crank fully locked up? How much for just that one?
mx724 Added a reply to 2000 cr250 part out
10/11/2018 6:38am Dm sent
mx724 Started a new thread Neken and Mika bar bends
8/9/2018 7:46am Was looking at some bar alternatives and notice the Neken specs appear to have taller height and sweep in comparison to Pro taper and Renthal twin walls. My current sweep is 53mm. Neken has nothing close. i must be missing something here. Anyone with Neken bars or Mika that can elaborate? 
This forum thread has 2 replies.
mx724 Added a reply to 14+ YZ250F BIG FAILURE
12/5/2016 10:25am Is this just the rod or pin and bearings as well.
mx724 Added a reply to 14+ YZ250F BIG FAILURE
12/5/2016 9:55am How much for the carrillo rod?
mx724 Added a reply to 2015 YZ450F 1/2 throttle Back fire on acceleration.1 Ft flames
7/28/2016 8:47am You mean throttle positioning sensor?
mx724 Added a reply to 2015 Yz250f problems
6/16/2016 11:55am Im not having any issues at the moment. Just looking. For a clear explination on how to if and when. I see guys do 2 things. Check the voltage, and check the angle. Was hoping someone would give a breakdown.
mx724 Added a reply to 2015 Yz250f problems
6/16/2016 8:22am Link? Ive seen quite a few post regarding this, but nothing with complete info on testing and proper installation of the TPS
mx724 Added a reply to 2015 yz250f only runs with choke on
6/16/2016 4:31am How did you test this when using the multi meter? Im not having the issue but i didnt see a clear order of operation in the manual? Also do they provide the angle to be set at? Juat looking for a bit more info as I may by a spare in anticipation
mx724 Added a reply to 2015 Yz250f problems
6/15/2016 9:13am Any luck sorting this out? Please let us know what you find.
mx724 Added a reply to 2015 YZ450F 1/2 throttle Back fire on acceleration.1 Ft flames
6/15/2016 9:11am Did you have any luck sorting this out? Ive seen these issues discussed enough to follow some of the threads. Please let us know what you may or may not have found.