Recent Activity
All
AZIMM84 Started a new thread 2004 KX450 suspension wheel swap from newer?
5/14/2025 11:14am I have a 2004 KX250 I am wanting to put the forks and wheels from my 2021 kx450. What all will work / won't work????
This forum thread has 1 reply.
AZIMM84 Added a reply to Burning Oil On Cold Start 2022 MC450
11/9/2024 1:03pm wossner
More »
AZIMM84 Added a reply to Burning Oil On Cold Start 2022 MC450
11/8/2024 7:44pm Was not honed, going to buy another set of rings and hone it and change the valve seals......
AZIMM84 Added a reply to Burning Oil On Cold Start 2022 MC450
11/6/2024 3:27pm more than a 2 stroke in 0* weather for about 4 mins then stops all together. Going to pull the head off this weekend
AZIMM84 Added a reply to Burning Oil On Cold Start 2022 MC450
11/4/2024 8:45pm Yes
AZIMM84 Started a new thread Burning Oil On Cold Start 2022 MC450
11/4/2024 8:56am 2022 Gas Gas 450. I sucked some sand into the bike and killed the old rings. Replaced piston, and had the head ported. Did a couple heat cycles and didn't have any issue. Now when the bike is cold it smokes and burns some oil until it heats up, once its hot it does not do it anymore... Cylinder was...
This forum thread has 12 replies.
AZIMM84 Started a new thread Suspension Swap Between Bikes?
7/28/2024 1:12pm I have a 22 RMZ 450 and a 22 KX450 What are the chances forks and shock would swap from the RMZ to the KX? As well as the rear wheel.
This forum thread has 0 replies.
AZIMM84 Added a reply to 2022 KX450SR issue after tune.
7/18/2023 6:04pm So I inspected my button, the rubber boot over the button is tore so I’m guessing its just full of water, no codes, bike still runs perfect. Did not know about the white coupler will give it a go!
AZIMM84 Started a new thread 2023 KTM 250 sx-f plastics on 2021?
6/19/2023 3:33pm Has anyone dove in yet before I start buying parts to see if they will work at all?
This forum thread has 2 replies.
AZIMM84 Started a new thread XCF-W Suspension tips
5/19/2023 10:52am Helping a buddy out who bought a woods bike play on Sandy MX track... besides obviously way to soft. Has anyone get one of these to work on a track without revalve? 2023 KTM 450 XCF-W Looking for a good base suspension setup for MX track,
This forum thread has 2 replies.
AZIMM84 Added a reply to Will this Yamaha suspension swap over?
4/19/2023 9:44am bummer
AZIMM84 Started a new thread Will this Yamaha suspension swap over?
4/19/2023 7:09am I have a 2021 yz250f with A kit suspension. Will shock and forks work on a 2020 yz250? I know the shock body is on the other side on the 250F but will it just flip?
This forum thread has 2 replies.
AZIMM84 Started a new thread Vortex Ecu on other years???
4/18/2023 6:14pm Will a vortex ecu from 2018 yz250f work on a 2021 yz250f, Clearly will need flashed but is ecu plug the same?
This forum thread has 0 replies.
AZIMM84 Added a reply to YZ250 died and won’t start !!
3/24/2023 1:02pm How long is that piston good for ?
AZIMM84 Added a reply to YZ250 died and won’t start !!
3/22/2023 4:55am We are going to be changing every 10 hours from here on out. Lesson learned.
AZIMM84 Added a reply to YZ250 died and won’t start !!
3/21/2023 10:02pm Little update, cleaned everything. Installed new Weisco piston. Moved needle to clip 3 in the carb. It has a 180 main 50 pilot. hopefully moving to clip 3 from 2 will richen it up enough to be a bit safer “if that’s what’s did it” fired up first kick!!!! let’s hope it’s good to go.
AZIMM84 Added a reply to YZ250 died and won’t start !!
3/17/2023 9:29am What is the difference between the two pistons ??
AZIMM84 Added a reply to YZ250 died and won’t start !!
3/17/2023 9:25am The pin was still there! No damage to the plating so maybe we got ultra lucky. The only thing I can think of is we added a sand tire to the bike and he was doing motos in deep wet sand without a jet change maybe it just got to hot?
AZIMM84 Added a reply to YZ250 died and won’t start !!
3/16/2023 2:35pm Btw no up and down play on the rod only side to side
AZIMM84 Added a reply to YZ250 died and won’t start !!
3/16/2023 1:30pm Yeah I really don’t know? This engine was done by pro circuit and its at 26 hours. Only thing we did was go from 40:1 to 32:1 and maybe it leaned it out to much?