Posts
31
Joined
8/14/2023
Location
Pittsfield, NH, USA
So I got a new to me 2016 yz250 that will start first kick almost everytime. Hot or cold. But there was something I noticed that if for some reason I can’t start it or I stall and can’t get it kicked after 2 kicks or so it will not let me kick it again without a bump start. I am truly baffled. I replaced the reeds as well as a new top end. Great compression new plugs. Just did the oil. But for whatever reason if I don’t get it sright away she ain’t starting. Any ideas? Is this a carb issue?
How does it run when it’s running?
check your air screw is set correctly and that it idles.
It runs great when running. Super fast and revs out and everything. Idles decently. 3-4 seconds before starts to rev down and may need a little throttle. But won’t die. I’m just baffled.
What should the air screw be at?
Goofy maybe, but is your fuel line routed near the pipe?
Getting a heat bubble.
The Shop
DeCal Works Huge Plastic Inventory of UFO and Polisport kits.
Luxon 4-Post Bar Mounts
$189.95 - $239.95
Typically around 2.5 turns out from all the way in.
but with the bike warmed up, turn the air screw all the way in, then quickly turn it out until it idles at its highest point.
obviously with any carb tuning it’s altitude and temp dependent so there is know exact setting.
My fuel line is not near the pipe at all. I’m thinking I’m gonna clean the carb this weekend and see if that helps. If I were to replace the carb what would be a good replacement?
Pilot circuit? It had ethanol in it before?
Maybe shit in the carburetor.
It's hard to diagnose problems on the internet.
The corn squeezin's are not our friends.
That shit fouls carbs quickly.
Yuuuuup. They def don’t like any ethanol. Been there done that 😂👎
I don’t use any ethanol. Just premium pump gas. I could really use some help solving this issue. Bc let’s face it. We still sometimes or fall even. It just doesn’t make sense why it doesn’t start after I’ve kicked it 5 times but will start the first kick. Any suggestions?
Check your float level. Often overlooked 2-stroke tuning secret.
Sure your premium gas is ethanol free?
My thought exactly. Unless the pump says ethanol free you're premium gas is gonna contain 10% methanol
Do the cheap stuff first - Check for Dirt in Gas Line. Dump it. Start Fresh. Replace Plug.
make sure your gas cap vent hose isn't blocked.
Old schoolers would tell you that you’re too rich on the pilot if it starts cold without the enrichener(choke). I would drop it one size.
remove the pilot and main jets and spray with carb cleaner
re-torque your the bolts on the head (squish could be slightly off)
check your carb vent hoses for dirt clogging the lines...
Pit Row
you do not need to replace the carburetor… most likely needs a thorough cleaning, check float height, check air screw setting, if you are less than one turn out or more than three turns out you need a different pilot jet. If it’s hard to start when hot and can start first kick when cold without choke that indicates really rich on the pilot circuit to me! Once that is sorted if you are running pump gas it has ethanol in it unless it specifically states it’s ethanol free… get in the habit of draining your carb bowl in between rides so the carb doesn’t get all nasty from congealed gas.
I’m sorry but it starts with the choke on cold. I forgot to state that. It’s really only something that happens after I like stall or what not and if I can’t get it kicked right away it has to be pop started. That’s not normal.
Are you new to 250 two strokes? Did you historically ride 4 strokes previous to this bike?
I only ask because you may not be twisting the throttle enough or at all while kicking to start it. Something to at least cover before you chase down other issues. Especially in a stall scenario.
Yes new to 2 strokes. But stall I mean if I wreck. So are you saying I always have to twist the throttle? I’m confused. I just believe it isn’t suppose to be like this. That is all. I’m gonna check the jets tomorrow and air screw. I had to get a small enough screw driver to be able to do it.
Yes, if you aren’t used to it and aren’t twisting the throttle a little bit while kicking it may be all that’s happening.
For awhile I would bring a carbed 250f and yz250 to ride at the track. While you don’t typically want to give the 250f any gas when kicking after a stall- different with the 2 stroke 250. Try it out atleast to rule it out.
Always twist the throttle a bit as you kick over on a 2 stroke.
If you crash/tip over... Hold it wide as you start.
If you've "wrecked" and the bike has been lying on it's side, the bike has flooded, fuel from the carb has flowed into the crank, open the throttle fully when you kick start the bike.
Post a reply to: 2016 yz250 finicky start