Factory Kawi Fork Tubes

401
Profile picture for user 401
Posts
19
Joined
2/7/2014
Location
Brawley, CA, USA
401
Edited Date/Time 2/7/2014 5:03pm
Was curious if anyone knows the deal with poto and wiemers fork tube coating? Does Showa set them up from the factory with it or are they powdercoated?
|
Xsenter
Profile picture for user Xsenter
Posts
481
Joined
9/25/2011
Location
SE
Xsenter 2/7/2014 12:16pm
2/7/2014 12:16pm
Same as factory Honda had a couple of years ago ...nothing new
TeamGreen
Profile picture for user TeamGreen
Posts
37729
Joined
11/25/2008
Location
Thru-out, CA, USA
TeamGreen 2/7/2014 12:26pm
2/7/2014 12:26pm
Peick has a set, too
401
Profile picture for user 401
Posts
19
Joined
2/7/2014
Location
Brawley, CA, USA
401 2/7/2014 12:32pm
2/7/2014 12:32pm
I know. I was wondering if anyone knew which of the two it was. I'm planning on powder coating mine, and hope it comes out looking half as clean as these.
MOTO120
Profile picture for user MOTO120
Posts
1375
Joined
3/21/2010
Location
MOTO, IL, USA
MOTO120 2/7/2014 12:38pm
2/7/2014 12:38pm
I'm gonna guess it is either a hard anodizing of some sort or a ceramic coating of some sort......I can guarantee you though that it is NOT a powder coating :-)

The Shop

See All »
BroFoSho
Profile picture for user BroFoSho
Posts
739
Joined
9/26/2013
Location
Tucson, AZ, USA
BroFoSho 2/7/2014 12:40pm
2/7/2014 12:40pm
It has to be a hard anodize.
I don't think they would want to coat the fork in anything because it will trap in more heat. That's bad enough for normal (spring) forks, and even worse for an air fork
GuyB
Profile picture for user GuyB
Posts
35722
Joined
7/10/2006
Location
Aliso Viejo, CA, USA
GuyB 2/7/2014 12:44pm
2/7/2014 12:44pm
MOTO120 wrote:
I'm gonna guess it is either a hard anodizing of some sort or a ceramic coating of some sort......I can guarantee you though that it is...
I'm gonna guess it is either a hard anodizing of some sort or a ceramic coating of some sort......I can guarantee you though that it is NOT a powder coating :-)
Anodizing.
401
Profile picture for user 401
Posts
19
Joined
2/7/2014
Location
Brawley, CA, USA
401 2/7/2014 12:44pm
2/7/2014 12:44pm
I didn't even think about ceramic coating. Now that I took a look at a few more pictures, it seems like that's the most possible.
GuyB
Profile picture for user GuyB
Posts
35722
Joined
7/10/2006
Location
Aliso Viejo, CA, USA
GuyB 2/7/2014 12:44pm
2/7/2014 12:44pm
BroFoSho wrote:
It has to be a hard anodize. I don't think they would want to coat the fork in anything because it will trap in more heat...
It has to be a hard anodize.
I don't think they would want to coat the fork in anything because it will trap in more heat. That's bad enough for normal (spring) forks, and even worse for an air fork
Well, plus the fact that with the added thickness you'd likely have trouble fitting them in the clamps...
401
Profile picture for user 401
Posts
19
Joined
2/7/2014
Location
Brawley, CA, USA
401 2/7/2014 12:48pm
2/7/2014 12:48pm
BroFoSho wrote:
It has to be a hard anodize. I don't think they would want to coat the fork in anything because it will trap in more heat...
It has to be a hard anodize.
I don't think they would want to coat the fork in anything because it will trap in more heat. That's bad enough for normal (spring) forks, and even worse for an air fork
GuyB wrote:
Well, plus the fact that with the added thickness you'd likely have trouble fitting them in the clamps...
Regardless, it looks trick.
Camp332
Profile picture for user Camp332
Posts
8760
Joined
8/16/2006
Location
Zoo Jersey, USA
Camp332 2/7/2014 12:58pm
2/7/2014 12:58pm
Don't powdercoat forktubes Bro's.
Big Lenny
Profile picture for user Big Lenny
Posts
14378
Joined
8/15/2006
Location
Compton, CA, USA
Big Lenny 2/7/2014 12:58pm
2/7/2014 12:58pm
It's a "Showa Thang"...
theToothPerry
Profile picture for user theToothPerry
Posts
538
Joined
11/23/2010
Location
Santa Clarita, CA, USA
theToothPerry 2/7/2014 1:01pm
2/7/2014 1:01pm
Theyre just sandblasted. Takes off the anodizing and leaves the silver look like what the hondas had a few years ago. Villos are anodized though.
Bradshaw560
Profile picture for user Bradshaw560
Posts
117
Joined
12/26/2013
Location
Marine City, MI, USA
Bradshaw560 2/7/2014 1:05pm
2/7/2014 1:05pm Edited Date/Time 2/7/2014 1:12pm
You don't want to just get your forks anodized or powdercoated.Unless its just on the outside or done by a suspension shop that knows what they are doing.MB1 does this check the site.250 for the forks and 250 for the shock
louis.bernard.564 2/7/2014 1:05pm
2/7/2014 1:05pm
MOTO120 wrote:
I'm gonna guess it is either a hard anodizing of some sort or a ceramic coating of some sort......I can guarantee you though that it is...
I'm gonna guess it is either a hard anodizing of some sort or a ceramic coating of some sort......I can guarantee you though that it is NOT a powder coating :-)
GuyB wrote:
Anodizing.
Thanks!
swedishfishmx 2/7/2014 1:17pm
2/7/2014 1:17pm
theToothPerry wrote:
Theyre just sandblasted. Takes off the anodizing and leaves the silver look like what the hondas had a few years ago. Villos are anodized though.
Sandblasted eh? If that's true then that's pretty quick and easy to do once you disassemble the forks that is.
401
Profile picture for user 401
Posts
19
Joined
2/7/2014
Location
Brawley, CA, USA
401 2/7/2014 2:59pm
2/7/2014 2:59pm
MOTORSPORTFOX wrote:
Like this? B) [img]https://p.vitalmx.com/photos/forums/2014/02/07/44609/s1200_401013_10201366389864900_2105386942_n.jpg[/img] [img]https://p.vitalmx.com/photos/forums/2014/02/07/44610/s1200_1005158_10201566356903951_696791871_n.jpg[/img]
Like this? Cool


Exactly haha
Rooster
Profile picture for user Rooster
Posts
4432
Joined
4/1/2008
Location
Edmonton, CA
Rooster 2/7/2014 3:33pm
2/7/2014 3:33pm
BroFoSho wrote:
It has to be a hard anodize. I don't think they would want to coat the fork in anything because it will trap in more heat...
It has to be a hard anodize.
I don't think they would want to coat the fork in anything because it will trap in more heat. That's bad enough for normal (spring) forks, and even worse for an air fork
GuyB wrote:
Well, plus the fact that with the added thickness you'd likely have trouble fitting them in the clamps...
The baking process can't be good for heat treated aluminium either.

Pit Row

See All »
nytsmaC
Profile picture for user nytsmaC
Posts
5946
Joined
8/10/2009
Location
Frig Off, CA
nytsmaC 2/7/2014 4:46pm
2/7/2014 4:46pm
Just curious, what is the advantage of hard coating the outer fork tubes? The inners make sense to me but I don't get what the DLC'd uppers are supposed to do better than stock other than look cool.
Rooster
Profile picture for user Rooster
Posts
4432
Joined
4/1/2008
Location
Edmonton, CA
Rooster 2/7/2014 5:03pm
2/7/2014 5:03pm
Just curious, what is the advantage of hard coating the outer fork tubes? The inners make sense to me but I don't get what the DLC'd uppers are supposed to do better than stock other than look cool.

Post a reply to: Factory Kawi Fork Tubes